molecalculator

Moles & Molar Mass

Quikrete Volume Calculator: How Much Concrete Do I Need?

Calculator No. 01-7474 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The Quikrete volume calculator determines how many bags of Quikrete concrete mix you need for a project, based on the dimensions of the area you’re filling. You enter the length, width, and depth (in feet or inches), and it returns the number of 40, 60, or 80 lb bags required, along with the total cubic feet and cubic yards. This is essential for planning any concrete project, from setting fence posts to pouring a patio slab.

Formula

The calculator uses the standard volume formula for a rectangular prism:

Volume (cubic feet) = Length (ft) × Width (ft) × Depth (ft)

Since depth is entered in inches, convert it to feet by dividing by 12. Then, to find cubic yards, divide the cubic feet by 27 (because 1 cubic yard = 27 cubic feet). The number of bags is calculated by dividing the total cubic feet by the volume of one bag:

  • 40 lb bag yields approximately 0.30 cubic feet (0.011 cubic yards)
  • 60 lb bag yields approximately 0.45 cubic feet (0.017 cubic yards)
  • 80 lb bag yields approximately 0.60 cubic feet (0.022 cubic yards)

These yields are standard for Quikrete concrete mixes (like 1101, 1103, and 1105) and assume proper mixing with water. Always round up to the nearest whole bag to avoid running short.

Worked Example

Using the default values: length = 10 ft, width = 10 ft, depth = 4 in, and 60 lb bags.

  1. Convert depth to feet: 4 in ÷ 12 = 0.3333 ft
  2. Calculate cubic feet: 10 ft × 10 ft × 0.3333 ft = 33.33 ft³
  3. Convert to cubic yards: 33.33 ft³ ÷ 27 = 1.2345 yd³ (rounded to 1.23 yd³)
  4. Calculate bags: 33.33 ft³ ÷ 0.45 ft³ per bag = 74.07 bags → round up to 75 bags

The calculator shows 1.23 cubic yards and 75 bags. This matches the default output.

Assumptions

  • The area is a rectangular prism with uniform depth.
  • The depth is the actual thickness of the concrete after placement, not the form height (if you have a gravel base, subtract that).
  • Bag yields are based on Quikrete’s published coverage for standard mixes; specialty mixes (like crack-resistant or high-strength) may have slightly different yields.
  • You are not accounting for waste, uneven subgrade, or spillage. It’s wise to add 5-10% extra.

How the Quikrete Calculator Works

Quikrete’s official online calculator (found on their website) is a simple form: you choose the shape (rectangle, circle, post hole, or footer), enter dimensions, and select bag size. It uses the same math as above, but for circles and post holes it uses the cylinder volume formula (π × radius² × height). For post holes, it subtracts the volume of the post itself. The key is to be consistent with units—if you enter inches for length, the calculator expects inches for width and depth. Most people make the mistake of mixing feet and inches, which throws off the result by a factor of 12.

Choosing the Right Bag Size

The bag size affects both the number of bags and the physical effort. A 40 lb bag is manageable for small projects like setting a few posts or repairing a walkway. A 60 lb bag is the most common for general slab work—it’s heavy but still liftable by most adults. An 80 lb bag is for larger pours, but it’s very heavy (about the weight of a large suitcase) and can be tough to mix by hand. For a 10×10 slab, you’d need 75 bags of 60 lb mix—that’s about 4,500 lb of concrete, which is far too much to mix by hand in a wheelbarrow. For anything over 1 cubic yard, consider ordering ready-mix concrete or renting a mixer. The calculator helps you see this before you start.

Common Mistakes and How to Avoid Them

  • Mixing units: Always convert everything to feet or inches before calculating. If you measure length in feet and width in inches, you’ll get a wildly wrong answer.
  • Forgetting to subtract post volume: For fence posts, the hole volume minus the post volume is the concrete needed. Many people calculate the hole only, over-ordering by 20-30%.
  • Ignoring waste: Concrete doesn’t always fill perfectly—uneven ground, spills, and over-excavation happen. Add 10% to the total.
  • Rounding down: Always round up to the nearest bag. You can’t buy a fraction of a bag, and running short mid-pour is a disaster.
  • Assuming bag yield is exact: The 0.45 ft³ per 60 lb bag is an average; actual yield can vary slightly with mix design and water content. Always have a couple extra bags on hand.

Cost Considerations

Bagged concrete is significantly more expensive per cubic yard than ready-mix. As a rough guide, a 60 lb bag costs $4-6, so 75 bags would be $300-450. Ready-mix concrete costs around $120-150 per cubic yard (plus delivery fees), so for 1.23 yd³ you’d pay $150-200 plus delivery, which might be $100-200. So for this slab, ready-mix is cheaper. However, for small jobs (under 0.5 yd³), bags are usually more practical because you avoid the delivery minimum and the need to schedule a truck. Also, bags allow you to mix in small batches, which is easier for DIYers.

Safety and Practical Tips

Concrete is caustic; it can cause skin burns. Wear gloves, long sleeves, and eye protection when handling dry mix or wet concrete. Avoid inhaling the dust—use a dust mask. When mixing, follow the manufacturer’s instructions on water amount; too much water weakens the concrete, too little makes it hard to work. For large pours, have a helper and a plan for moving the concrete quickly. Never pour concrete in freezing temperatures or when rain is expected within 24 hours. Also, check local building codes for required slab thickness (typically 4 inches for patios, 6 inches for driveways).

Frequently Asked Questions

How many 60 lb bags of Quikrete are in a cubic yard?

One cubic yard equals 27 cubic feet. Since a 60 lb bag yields 0.45 ft³, you’ll need 27 ÷ 0.45 = 60 bags. So 60 bags of 60 lb mix make exactly 1 cubic yard.

Can I use the calculator for a circular pad?

Yes, but you need the circle formula: Volume = π × radius² × depth. For example, a 10-foot diameter circle (radius 5 ft) at 4 inches deep is 3.1416 × 5² × 0.333 = 26.18 ft³. Then divide by 0.45 to get bags (58 bags). The Quikrete site has a separate circle calculator, but you can do it manually with this math.

How many bags of Quikrete do I need for a 10×10 slab?

Assuming 4 inches thick, you need 1.23 cubic yards (33.33 ft³). With 60 lb bags, that’s 33.33 ÷ 0.45 = 74.07, so 75 bags. With 80 lb bags (0.60 ft³ each), you’d need 33.33 ÷ 0.60 = 55.6, so 56 bags.

What if my depth is not uniform?

If your subgrade is uneven, calculate the average depth. For a more accurate estimate, divide the area into sections of roughly uniform depth, calculate each, and sum them. This is common for driveways with a crown or sloped patios.

Should I add extra bags for waste?

Yes, it’s standard practice to add 5-10% to your total. For a 75-bag job, add 4-8 bags. This covers spillage, over-excavation, and any mistakes. Unopened bags can be returned to most home improvement stores, so it’s safer to have extra.

Does the calculator work for Quikrete’s other products like mortar or sand mix?

No, the yields differ. Mortar mix and sand mix have different densities and coverage rates. Always use the specific product’s coverage data, which is printed on the bag or on Quikrete’s website. For instance, Quikrete Sand Mix yields about 0.60 ft³ per 60 lb bag, but it’s not the same as concrete mix.

Related

Formula used
in ft | Length | ft | 10 | 0.01
in ft | Width | ft | 10 | 0.01
in in | Depth | in | 4 | 0.01
sel bag | Bag size | 60 lb=0.45, 40 lb=0.3, 80 lb=0.6
out yds | Concrete volume | cubic yards | (l * w * (d / 12)) / 27 | 2
out bags | Bags needed | bags | ceil(((l * w * (d / 12)) / 27) * 27 / bag) | 0
out ft3 | Concrete volume | cubic feet | l * w * (d / 12) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →