molecalculator

Moles & Molar Mass

Rotor Centrifuge Radius Calculator and Formula

Calculator No. 01-2815 · Updated · Formula and assumptions shown below

Rotor radius 9.9978 cm
Rotor radius
99.978 mm
= Rotor radius × 10
Rotor speed
10000 rpm
Set in the form below
Relative centrifugal force
11180 ×g
Set in the form below
You enter
Rotor speed (rpm), Relative centrifugal force (×g)
You get
Rotor radius (cm), Rotor radius (mm)
Rounding
4 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds a centrifuge rotor’s radius in metres from its rotational speed and relative centrifugal force (RCF, or ×g). Enter the rotor speed in revolutions per minute (rpm) and the stated RCF; the result is the distance from the axis of rotation to the sample position that corresponds to those values.

Formula

The radius follows from the relationship between rotational speed and centripetal acceleration:

RCF = (2π × rpm / 60)² × r / 9.80665

Rearranged for radius in centimetres:

r (cm) = RCF × 9.80665 / (2π × rpm / 60)² × 100

  • RCF is relative centrifugal force, expressed as a multiple of standard gravitational acceleration (×g).
  • rpm is rotor speed in revolutions per minute; dividing by 60 converts it to revolutions per second.
  • r is radius in metres in the acceleration equation, measured from the axis of rotation to the sample location.
  • 9.80665 m/s² is standard gravitational acceleration. Multiplying the result in metres by 100 gives centimetres; multiplying centimetres by 10 gives millimetres.

The calculator assumes that the entered RCF and rpm refer to the same sample position. Rotor manufacturers and laboratory protocols may report RCF at the maximum radius, minimum radius, or another specified point, so the measurement convention matters.

Worked Example

Using the defaults, the rotor speed is 10,000 rpm and the RCF is 11,180 ×g.

  1. Convert the speed: 10,000 rpm / 60 = 166.66667 revolutions per second.
  2. Calculate angular speed: 2π × 166.66667 = 1,047.1976 radians per second.
  3. Square angular speed: 1,047.1976² ≈ 1,096,622.7 s⁻².
  4. Calculate radius: (11,180 × 9.80665) / 1,096,622.7 × 100 ≈ 9.9966 cm.

The calculator displays 9.9966 cm and 99.966 mm for these inputs. Small differences in the final displayed digits can arise if intermediate values are rounded earlier.

Assumptions

  • The rotor rotates at a steady speed, and the motion is treated as circular.
  • The stated RCF is the acceleration at the radius being calculated, relative to standard gravity.
  • The rpm and RCF values use compatible definitions and refer to the same sample position.
  • This is a calculation aid; it does not establish whether a rotor or tube is suitable for a particular speed or force.

What “Rotor Radius” Means

Rotor radius is not always a single obvious dimension. In centrifuge calculations, it is the distance from the rotation axis to the point in the sample whose RCF is being described. It is not necessarily the rotor’s outside diameter, the radius of a tube, or the distance from the centre of the rotor to the tube’s outer wall.

For a fixed-angle rotor, the sample spans a range of distances from the axis. For a swinging-bucket rotor, the bucket changes orientation as it spins, and sample positions likewise occupy different radii. As a result, an instrument’s stated maximum RCF may describe the force at the bottom or outermost sample position, while the force closer to the axis is lower.

When a protocol gives an RCF, it generally describes the desired centrifugal force rather than a universal rotor dimension. You can use the equation to infer the effective radius implied by a particular speed–RCF pair, but that inferred value is meaningful only under the same measurement convention used by the protocol or instrument documentation.

How to Use the Result

Enter rpm and RCF from the same source, then read the radius in centimetres or millimetres. The radius is useful for checking whether a quoted RCF is plausible for a rotor at its stated speed, or for understanding how an instrument converts between rpm and ×g.

  • If the source gives RCF and rpm, calculate the implied radius and compare it with the documented radius for the specified sample position.
  • If you know the rotor radius and rpm but need RCF, use the original equation rather than interpreting the calculator’s radius output as a direct force setting.
  • If a document gives only rpm, it is not enough to determine RCF without a radius.

Always distinguish rpm from RCF. Rpm describes how fast the rotor turns; RCF describes the resulting acceleration relative to gravity. Two rotors at the same rpm can apply different forces because their sample radii differ. Conversely, to produce the same RCF, a smaller-radius rotor must generally turn faster.

Common Errors and Limits

A common mistake is to treat rpm as though it directly states the force. The relationship depends on the square of rotational speed: at a fixed radius, doubling rpm produces four times the RCF. This also means that a modest speed-entry error can noticeably affect a calculated radius.

  • Mixing up radius and diameter: if a manual gives a diameter, halve it to obtain the corresponding radius; do not enter the diameter as the radius in an RCF calculation.
  • Using mismatched reference points: a maximum RCF and a radius measured to the sample’s midpoint will not necessarily agree.
  • Confusing units: the formula uses acceleration in m/s² and converts metres to centimetres explicitly. The inputs are rpm and ×g, not rad/s and m/s².
  • Assuming one radius describes every sample position: force varies with distance from the axis, even within a single tube.

The equation is a physical relationship, not a rotor validation tool. It cannot determine maximum safe speed, rotor condition, tube compatibility, balancing requirements, or whether a protocol is appropriate. Consult the instrument documentation and applicable laboratory procedure for those decisions. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the radius of a centrifuge rotor?
The radius is the distance from the rotor’s axis of rotation to the sample position used for the force calculation. It may refer to the sample bottom, midpoint, or another specified location, not necessarily the rotor’s outer edge.

How do I calculate rotor radius from rpm and RCF?
Use r = RCF × 9.80665 / (2π × rpm / 60)², with the result in metres. Multiply by 100 for centimetres or by 1,000 for millimetres.

Can I find RCF from rpm alone?
No. You also need the effective radius to the sample position. At the same rpm, a larger radius produces a larger RCF.

Is rotor radius the same as rotor diameter?
No. Diameter is twice the radius. In addition, the relevant radius is usually measured from the rotation axis to the sample location, which may differ from the rotor’s outside dimensions.

Why does my calculated radius differ from the manual?
The manual may report maximum RCF at a different point than the radius you are comparing, or values may be rounded. Check that rpm, RCF, units, and reference position all match.

Related

Formula used
in rpm | Rotor speed | rpm | 10000 | 0
in rcf | Relative centrifugal force | ×g | 11180 | 0
out r | Rotor radius | cm | (rcf * 9.80665) / ((2 * pi * rpm / 60) ^ 2) * 100 | 4
out rm | Rotor radius | mm | r * 10 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →