Convert relative centrifugal force (RCF, or ×g) to revolutions per minute (rpm) using the rotor radius: rpm = 1,000 × √[RCF ÷ (1.118 × 10⁻⁵ × r)], with r in centimetres. Enter the RCF and radius below to calculate rpm; the result is the rotational speed needed to produce that acceleration at that radius.
Formula
The conversion follows the relationship between centripetal acceleration and rotational speed:
RCF = 1.118 × 10⁻⁵ × r × rpm²
- RCF is relative centrifugal force, expressed as a multiple of standard gravitational acceleration, or ×g. It is dimensionless.
- r is the distance from the axis of rotation to the point of interest, in centimetres (cm).
- rpm is rotational speed in revolutions per minute.
Solving for speed gives rpm = √[RCF ÷ (1.118 × 10⁻⁵ × r)]. The calculator multiplies that square root by 1,000 because its expression is algebraically written as 1,000 × √[RCF ÷ (1.118 × 10⁻⁵ × r)]. The coefficient incorporates the conversion from revolutions per minute to angular speed and the standard gravitational acceleration used to express the result in ×g. The second output is angular speed in radians per second: rpm × 2π ÷ 60.
Worked Example
With the default inputs, RCF = 1,000 ×g and r = 10 cm:
- Substitute into the conversion: rpm = 1,000 × √[1,000 ÷ (1.118 × 10⁻⁵ × 10)].
- Calculate the denominator: 1.118 × 10⁻⁵ × 10 = 0.0001118.
- Divide: 1,000 ÷ 0.0001118 ≈ 8,944,543.8283.
- Take the square root and multiply by 1,000: rpm ≈ 2,990,743.1. Rounded to the calculator’s zero decimal places, the result is 2,990,743 rpm.
- Angular speed is 2,990,743.1 × 2π ÷ 60 ≈ 313,188.57 rad/s.
Assumptions
- The entered radius is in centimetres and is measured from the rotation axis to the specific point where the stated RCF applies.
- The formula uses the conventional coefficient 1.118 × 10⁻⁵, based on standard gravity. Small differences in constants or rounding can produce slight differences from a centrifuge’s display or another calculator.
- The calculation describes ideal rotational motion; it does not account for rotor geometry, acceleration or braking, sample movement, or instrument-specific calibration.
What RCF and RPM Mean
RPM counts how many complete turns a rotor makes in one minute. RCF describes the acceleration produced by that rotation relative to standard gravity. They are related, but they are not interchangeable: rpm states a speed, while RCF states an acceleration at a particular radius.
That radius matters because a point farther from the rotation axis travels in a larger circle. At the same rpm, the outer part of a rotor experiences greater centripetal acceleration than a point closer to the axis. Consequently, there is no single universal rpm equivalent for a given RCF. A speed that produces 1,000 ×g with one rotor radius will produce a different RCF with another.
Choosing the Correct Rotor Radius
Use the radius associated with the point where you want the stated force, not simply a convenient measurement of the rotor. A centrifuge’s documentation may provide minimum, average, or maximum sample radius. These refer to different positions in a tube or rotor and therefore give different RCF values at the same rpm.
- Maximum RCF: use the distance from the axis to the farthest point of the sample, if the requested force is the maximum along the sample.
- Average RCF: use the radius specified for average force when comparing a protocol that explicitly uses that convention.
- Minimum RCF: use the nearest relevant sample point when a protocol specifies minimum force.
Follow the rotor or instrument documentation and the convention used by the method. If a method gives RCF but does not say whether it means minimum, average, or maximum, check its instructions rather than assuming. A radius measured from the rotor centre to the bottom of a tube may not match the method’s chosen sample radius.
Using the Conversion in Practice
To convert a requested RCF to rpm, first identify the required radius in centimetres. Enter that radius and the RCF, then use the calculated rpm as a mathematical conversion—not as permission to exceed the equipment’s limits. Verify that the selected rotor, tubes, adapters, and centrifuge are approved for the intended speed and operating conditions. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
For the reverse conversion, rearrange the same equation: RCF = 1.118 × 10⁻⁵ × r × rpm². This calculates the force at a known radius and speed. If a rotor runs at 5,000 rpm, for example, the RCF depends on its radius; rpm alone is not enough to determine force.
Common Errors and Limits
- Mixing radius and diameter: the formula requires radius, measured from the axis to the point of interest. Entering a diameter doubles the radius and gives an incorrect conversion.
- Using millimetres as centimetres: convert first. For example, 100 mm is 10 cm. The calculator’s radius input is in centimetres.
- Assuming RCF has one matching rpm: the required speed changes with radius, so always use the radius for the rotor and sample position in question.
- Rounding too early: retain the unrounded result for calculations or settings, then round only to a speed the equipment can actually set.
- Ignoring equipment limits: the equation does not establish that a rotor, vessel, or instrument can safely operate at the calculated speed. Consult its stated limits.
The coefficient is a conventional rounded value, so tiny numerical differences are possible between conversion tools. More importantly, the equation does not replace a centrifuge’s own RCF guidance, nor does it account for rotor-specific operating restrictions.
Frequently Asked Questions
How do I convert RCF to rpm?
Use rpm = √[RCF ÷ (1.118 × 10⁻⁵ × r)], with RCF as a multiple of ×g and radius r in centimetres. The calculator above applies this formula.
Can I convert RCF to rpm without knowing the radius?
No. The same RCF can correspond to different rpm values at different radii. Find the relevant radius in the rotor or centrifuge documentation.
Is RCF the same as rpm?
No. RPM is rotational speed; RCF is the acceleration relative to gravity at a specified radius. They are connected by a formula, but one cannot be specified from the other without the radius.
Should I use the minimum, average, or maximum radius?
Use the radius convention specified by the method or equipment documentation. These values represent different points in the sample and will not produce identical RCF-to-rpm conversions.
How do I convert rpm back to RCF?
Calculate RCF = 1.118 × 10⁻⁵ × r × rpm², with radius in centimetres and speed in rpm.
Related
Formula used
in rcf | Relative centrifugal force | ×g | 1000 | 0 in r | Rotor radius | cm | 10 | 0 out rpm | Rotational speed | rpm | 1000 * sqrt(rcf / (1.118 * 10^-5 * r)) | 0 out rad | Angular speed | rad/s | rpm * 2 * pi / 60 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol