molecalculator

Moles & Molar Mass

Hz to RPM: Frequency to Rotational Speed Converter

Calculator No. 01-7368 · Updated · Formula and assumptions shown below

Rotational speed 3,600.00 RPM
Rotations per second
60.00 RPS
= Frequency ÷ Pulses per revolution
Frequency
60 Hz
Set in the form below
Pulses per revolution
1
Set in the form below
You enter
Frequency (Hz), Pulses per revolution
You get
Rotational speed (RPM), Rotations per second (RPS)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts frequency in hertz (Hz) to rotational speed in revolutions per minute (RPM), and vice versa. You enter the frequency in hertz and the number of pulses or events per revolution (if applicable), and the calculator returns the equivalent RPM. For a motor driven by a 60 Hz AC supply with one electrical cycle per mechanical revolution, the answer is 3600 RPM.

Formula

The core relationship is:

RPM = (Frequency in Hz × 60) / Pulses per revolution

Where:

  • RPM = revolutions per minute (dimensionless count of full rotations per minute)
  • Frequency (Hz) = number of cycles or events per second (1 Hz = 1 event/s)
  • 60 = conversion factor from seconds to minutes (60 s/min)
  • Pulses per revolution = number of pulses, electrical cycles, or encoder lines per single full mechanical revolution (dimensionless)

If you have RPM and want Hz, rearrange: Frequency (Hz) = RPM × Pulses per revolution / 60.

Worked Example

Using the default values from the calculator (frequency = 60 Hz, pulses per revolution = 1):

  1. Start with the formula: RPM = f × 60 / ppr
  2. Substitute the values: RPM = 60 × 60 / 1
  3. Multiply: 60 × 60 = 3600
  4. Divide by ppr: 3600 / 1 = 3600

The calculator shows 3600.00 RPM, which matches. This is the synchronous speed of a 2-pole AC motor on a 60 Hz supply.

Assumptions

  • Each pulse or electrical cycle corresponds to exactly one full mechanical revolution (ppr = 1).
  • The frequency is constant and the rotation is uniform (no slip or variation).
  • For AC motors, this is the synchronous speed; the actual rotor speed is slightly lower due to slip.

Background: Why Hz and RPM Are Related

Hertz (Hz) measures frequency—how many times something repeats per second. RPM (revolutions per minute) measures rotational speed—how many full turns an object makes in one minute. They are directly linked because a rotation is a repeating event: one revolution is one cycle. The only difference is the time unit (seconds vs. minutes) and possibly the number of cycles per revolution.

In electrical engineering, the relationship is especially important for AC induction motors. The synchronous speed of an AC motor is given by:
Synchronous RPM = (120 × Frequency in Hz) / Number of poles

This formula comes from the fact that each pole pair completes one full electrical cycle per mechanical revolution. For a 2-pole motor (one pole pair), ppr = 1, so the formula reduces to RPM = 60 × Hz. For a 4-pole motor (two pole pairs), ppr = 2, so RPM = 30 × Hz. This is why a 60 Hz, 2-pole motor runs at 3600 RPM, while a 50 Hz, 4-pole motor runs at 1500 RPM.

How the Conversion Works in Practice

In real-world measurement, you often get a frequency signal from a sensor—for example, an optical encoder that outputs a certain number of pulses per revolution. To convert that pulse frequency to RPM, you use the same formula with ppr equal to the encoder’s line count.

Example: An encoder with 1000 pulses per revolution outputs a 5 kHz signal. What is the shaft speed?
RPM = 5000 Hz × 60 / 1000 = 300 RPM.

Conversely, if you know a shaft spins at 1200 RPM and the encoder has 500 lines, the output frequency is:
Hz = 1200 × 500 / 60 = 10,000 Hz = 10 kHz.

This conversion is used in tachometers, CNC machines, robotics, and any system that measures rotational speed via pulse counting.

Common Misconceptions and Pitfalls

A frequent mistake is forgetting the factor of 60. Since Hz is per second and RPM is per minute, you must multiply by 60. Another error is assuming ppr = 1 when it is not. For example, a 4-pole AC motor has two electrical cycles per revolution, so using ppr = 1 would give double the actual synchronous speed.

Another subtlety: for AC induction motors, the actual rotor speed is always less than the synchronous speed due to slip. The calculator gives the synchronous speed; the real motor speed at full load might be 3500 RPM for a 3600 RPM rated motor. If you are measuring actual shaft speed with an encoder, the ppr is the encoder’s line count, not the motor’s pole count.

Also note that some devices output a frequency that is not directly proportional to RPM—for example, a gearbox changes the relationship. Always account for any gearing between the rotating element and the frequency source.

How to Choose the Right Conversion

To decide which formula to use, identify what you know and what you need:

  • If you have a frequency in Hz and want RPM, use RPM = (Hz × 60) / ppr.
  • If you have RPM and want Hz, use Hz = (RPM × ppr) / 60.
  • If you have a motor’s pole count and supply frequency, use RPM = (120 × Hz) / poles (this is the same as the general formula with ppr = poles/2).

For example, a 6-pole motor on 50 Hz has synchronous speed = (120 × 50) / 6 = 1000 RPM. Using the calculator, enter f = 50 and ppr = 3 (since 6 poles = 3 pole pairs), and you get 1000 RPM.

Always double-check your ppr value. If you are working with a gearbox, divide the output RPM by the gear ratio to get the input RPM, or adjust the ppr accordingly.

Practical Applications

This conversion is not just academic—it is used daily in many fields:

  • Electric motors: Determining synchronous speed from supply frequency and pole count.
  • Encoders and tachometers: Converting pulse frequency to shaft RPM for speed monitoring.
  • Audio and vibration: Relating rotational frequency (in Hz) to RPM for machinery analysis (e.g., a shaft rotating at 30 Hz is 1800 RPM).
  • Centrifuges and fans: Setting speed in RPM when the drive frequency is known.
  • Robotics and CNC: Coordinating motor speeds with controller frequency outputs.

In each case, the same simple math applies—just be careful with the ppr factor.

Frequently Asked Questions

How many RPM is 1 Hz?

If one revolution equals one cycle (ppr = 1), then 1 Hz equals 60 RPM. This is because there are 60 seconds in a minute. For example, a shaft spinning at 1 revolution per second is rotating at 60 RPM.

What is the formula to convert Hz to RPM for a 4-pole motor?

For a 4-pole motor, there are 2 pole pairs, so ppr = 2. The formula becomes RPM = (Hz × 60) / 2 = Hz × 30. On a 60 Hz supply, that gives 1800 RPM synchronous speed. On 50 Hz, it gives 1500 RPM.

Why is the actual motor speed lower than the calculated RPM?

For AC induction motors, the rotor cannot quite keep up with the rotating magnetic field; the difference is called slip. Slip is typically 2–5% at full load. So a 3600 RPM synchronous motor might run at about 3500 RPM under load. The calculator gives the theoretical synchronous speed, not the actual shaft speed.

Can I use this calculator for a stepper motor?

Stepper motors are driven by pulse trains, not AC frequency. If you know the steps per revolution (e.g., 200 steps/rev), then the pulse frequency in Hz divided by steps per revolution gives revolutions per second, and multiplying by 60 gives RPM. Enter the steps per revolution as ppr in the calculator. For 200 steps/rev and a 1 kHz pulse rate, RPM = 1000 × 60 / 200 = 300 RPM.

What is the difference between Hz and RPM in vibration analysis?

In vibration analysis, Hz is often used for frequency (cycles per second), while RPM is used for rotational speed. A machine rotating at 1200 RPM has a fundamental vibration frequency of 20 Hz (1200/60). The conversion is the same: divide RPM by 60 to get Hz, or multiply Hz by 60 to get RPM.

Does the conversion change for metric vs. imperial units?

No. Hz and RPM are unit-independent—they are both based on time (seconds and minutes). The conversion factor of 60 is constant regardless of the system of measurement. The only thing that changes is the ppr, which depends on the machine’s design, not on units.

Related

Formula used
in f | Frequency | Hz | 60 | 0
in ppr | Pulses per revolution | - | 1 | 0.001
out rpm | Rotational speed | RPM | f * 60 / ppr | 2
out rps | Rotations per second | RPS | f / ppr | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →