This calculator finds the molarity of a solution from the solute’s mass, molar mass, and final solution volume; enter those three values to get concentration in mol/L and mM. Molarity and volume are inversely related when the amount of dissolved solute is fixed: increasing the final volume lowers the molarity, while decreasing it raises the molarity.
Formula
Molarity is the number of moles of solute divided by the final volume of the solution in liters:
M = n / V
- M is molarity, in moles per liter (mol/L).
- n is the amount of solute, in moles (mol).
- V is the final solution volume, in liters (L).
If the solute amount is fixed, this can be rearranged as n = M × V. It also shows the direct link between molarity and volume: for a fixed number of moles, molarity varies inversely with volume. For example, doubling the volume halves the molarity.
This calculator gets moles from mass using n = m / MM, where m is solute mass in grams and MM is molar mass in grams per mole. Since the entered volume is in milliliters, it converts to liters by dividing by 1000:
M = m / [MM × (VmL / 1000)]
The conversion factor 1000 mL per L is explicit in the calculation. The millimolar result is molarity multiplied by 1000; 1 mol/L equals 1000 mM.
Worked Example
Using the calculator’s defaults: 2.922 g of solute, a molar mass of 58.44 g/mol, and a final solution volume of 250 mL.
- Convert volume to liters: 250 mL / 1000 = 0.25000 L.
- Calculate the amount of solute: 2.922 g / 58.44 g/mol = 0.050000 mol.
- Divide moles by liters: 0.050000 mol / 0.25000 L = 0.2000 mol/L.
- Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.
The calculator displays the molarity as 0.2000 mol/L and the concentration as 200.00 mM, following the specified decimal places.
Assumptions
- The entered mass is the mass of the solute, and its molar mass is appropriate for the chemical form being counted.
- The volume is the final volume of the complete solution, not the volume of solvent added.
- The calculation treats the supplied mass, molar mass, and volume as measured values; it does not estimate measurement uncertainty or chemical purity.
- No assumption about dissociation is needed to calculate formal molarity. The result is moles of the named solute formula units per liter, not necessarily the concentration of each ion.
How Molarity and Volume Relate
Molarity describes concentration by volume: it tells how many moles of solute are present in each liter of solution. Volume alone does not determine molarity. You also need the amount of solute, or enough information—such as mass and molar mass—to calculate that amount.
For a fixed solute amount, the relationship is reciprocal. A solution containing 0.10 mol in 0.50 L has a molarity of 0.20 mol/L. If that same amount is brought to a final volume of 1.00 L, its molarity becomes 0.10 mol/L. The moles have not changed; they are spread through twice the volume.
In practice, “volume” means the volume of the finished solution. Adding 250 mL of water to a solid does not necessarily produce 250 mL of solution: the dissolved material also occupies volume, and mixing can change the total. For concentration calculations, use the final solution volume specified by the preparation or measurement, not merely the solvent volume.
Using the Relationship for Dilution
When a solution is diluted, the solvent is added but the amount of solute is assumed to stay constant. Equating the initial and final amounts of solute gives:
M1V1 = M2V2
Here, M1 and V1 are the starting concentration and volume, while M2 and V2 are the concentration and final volume. The two volumes must use the same units, and the concentration units must also match.
For example, if 10 mL of a 2 mol/L solution is diluted to a final volume of 100 mL, then M2 = (2 mol/L × 10 mL) / 100 mL = 0.20 mol/L. The mL values cancel because both volumes use the same unit. This equation does not apply unchanged if solute is added, removed, reacts, precipitates, or otherwise stops remaining in the solution as assumed.
Common Errors and Limits
- Using mL as if it were L: Convert milliliters to liters by dividing by 1000 before using M = n/V. Forgetting this conversion changes the answer by a factor of 1000.
- Confusing solvent and solution volume: Molarity uses the total final solution volume, not the starting volume of water or another solvent.
- Mixing up direct and inverse relationships: At fixed moles, larger volume means lower molarity. If molarity is fixed instead, increasing volume requires more moles.
- Rounding too early: Keep extra digits through intermediate steps, then round the final result to a precision justified by the measurements. A displayed decimal count does not guarantee that the input measurements were equally precise.
- Ignoring chemical form: Molar mass depends on the compound and its form. A hydrated salt, for example, has a different molar mass from the corresponding anhydrous compound.
Molarity is based on solution volume, which can change with temperature as liquids expand or contract. For high-accuracy work, use the temperature and volume conditions required by the method. Molarity is also distinct from molality, which is moles of solute per kilogram of solvent; the two are not interchangeable, especially when comparing solutions with different densities or temperatures. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
Does molarity increase when volume increases?
Not if the amount of solute stays fixed. In that case, increasing volume lowers molarity because the same number of moles is distributed through more solution. If concentration is held fixed instead, a larger volume contains more moles.
How do I calculate volume from molarity and moles?
Rearrange M = n/V to get V = n/M. If n is in moles and M is in mol/L, the volume is in liters. Multiply liters by 1000 to express the result in milliliters.
Can I use milliliters in the molarity formula?
Yes, provided you convert them to liters or use a consistent conversion explicitly. For M in mol/L and V in mL, write M = n / (VmL/1000); do not divide moles directly by an unconverted milliliter value.
Is molarity the same as moles per milliliter?
No. Molarity is defined in moles per liter. One mol/L equals 0.001 mol/mL, or 1 mmol/mL; confusing the units can produce a thousandfold error.
Why does adding water lower molarity?
In an ordinary dilution, water increases the final volume while the solute amount remains approximately constant. Because M = n/V, the larger denominator gives a lower molarity.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol