A router radius is the rounded distance a router bit cuts at an edge or in a profile; choosing the right radius depends on the finished shape, the bit’s geometry, and the material. This guide explains how to identify radius, select a suitable bit, and avoid common measurement and safety mistakes.
What “router radius” means
In woodworking, radius usually describes the curve made by a bit. On a simple roundover bit, the radius is the distance from the curve’s center to its surface. A larger radius makes a fuller, more gradual curve; a smaller one produces a tighter roundover. Radius is not the same as diameter: diameter is twice the radius.
Router bits are commonly labeled by their profile and dimensions, such as a 6 mm roundover. Check the manufacturer’s drawing or specification to confirm whether a listed measurement means the radius, cutting depth, or another dimension. A roundover bit may also have a bearing, which guides the cut along an edge; the bearing size and position affect the cut depth.
How the cut radius relates to the board
For an ordinary roundover on a square board edge, the bit rounds the corner between the board’s face and edge. If the board is thick enough and the cutter is set for a complete quarter-circle, the radius determines how much material is removed from each adjoining face. For example, a 6 mm radius takes up about 6 mm of the face and 6 mm of the edge at the corner. This assumes the bit is set to produce the full profile and that the workpiece is thick enough.
That relationship does not mean every cut labeled “6 mm” will leave the same finished dimensions. The cutter’s profile, bearing, fence or guide setup, and depth setting all matter. A partial-depth pass can create a smaller-looking curve or a decorative profile that is not a true quarter-circle. Always verify the actual bit diagram and make a test cut in scrap of similar thickness.
How to choose a radius
Start with the design and the size of the material, not simply the largest bit available. A modest radius often softens a sharp edge without making a narrow rail or thin panel look undersized. A large radius can be appropriate for a substantial tabletop edge, but it removes more material and may leave too little flat surface.
- Match the drawing: Use the specified radius when a plan, mating part, or replacement component requires a particular profile.
- Consider thickness: The stock must be thick enough for the selected profile. A radius that is too large can consume most of a thin edge.
- Think about use: Edges that are frequently handled may benefit from a more comfortable roundover, while crisp, modern designs may call for a smaller one.
- Check adjoining parts: A rounded edge can affect joints, clearances, and how two pieces meet. Keep the profile outside areas that need a sharp, square fit.
- Test the finish: Cut a sample and inspect it from several angles before routing the finished workpiece.
There is no universally correct radius for furniture or trim. The best choice is the one that fits the design, leaves adequate material, and can be cut cleanly with the bit and router setup available.
Radius, diameter, and common bit measurements
Radius and diameter are easy to confuse. If a curve has a 12 mm diameter, its radius is 6 mm. Conversely, a 6 mm radius corresponds to a 12 mm diameter. Do not infer the cutting radius from the overall width of a bit: the shank, bearing, and cutter body are not the curve itself.
Different bit profiles also use different measurements. A roundover bit is intended to soften an edge, while a cove bit cuts a concave curve. A chamfer bit makes a flat angled face, not a rounded radius. A Roman ogee or other decorative cutter combines curves and sometimes a flat or bead, so one radius alone does not describe the whole shape.
Setup and common problems
Before cutting, confirm that the bit is suitable for the router, properly seated in the collet, and within the router and bit maker’s speed limits. Set the cut depth according to the bit instructions, secure the workpiece, and use a guide or bearing as designed. Make shallow passes when needed rather than forcing a deep cut in one pass; the appropriate pass depth depends on the bit, material, and machine.
- Burn marks: A dull bit, excessive feed hesitation, unsuitable speed, or buildup on the cutter can scorch wood. Keep the cutter clean and move at a controlled, steady rate.
- Chipped edges: Grain direction and fragile material can cause tear-out. Test the cut, support the work, and use a suitable feed direction and pass strategy for the setup.
- Uneven profile: A loose guide, an inconsistent bearing contact, or a changing depth setting can make the radius vary. Check the setup before each pass.
- Unexpectedly small roundover: The depth may be set for a partial profile, or the labeled dimension may refer to something other than radius. Consult the drawing and test on scrap.
Router work requires eye and hearing protection, secure workholding, and attention to the tool manual. Keep hands clear of the cutter, disconnect power before changing a bit, and do not use damaged or loose cutters. Follow the router and bit manufacturers’ safety instructions.
Frequently Asked Questions
How do I calculate the radius from a diameter?
Divide the diameter by two. For example, a 10 mm diameter corresponds to a 5 mm radius.
Does a 6 mm roundover bit always cut a 6 mm radius?
Not necessarily unless the marking specifically identifies the radius and the bit is set to make its full intended profile. Check the bit’s specification and confirm with a test cut.
What radius should I use on a table edge?
Choose one that suits the table’s thickness, design, and use. Check the plans if available, and test the profile on scrap before routing the tabletop.
Can I use a roundover bit on thin material?
Only if the profile and setup leave enough material and the bit is appropriate for the work. A large radius can remove too much from a thin edge; test first and follow the bit instructions.
Is a roundover radius the same as the bearing size?
No. The radius describes the curve; the bearing guides the bit along an edge. Their dimensions serve different purposes, although the bearing’s position can influence how deeply the cutter engages.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp