Router radius settings determine the size of the rounded edge a router bit cuts: the radius is the distance from the curve’s center to its surface. Choose a radius that matches the desired profile and the material, then make a test cut; a router itself usually has no universal radius dial, because the bit’s shape and dimensions set the cut.
What “router radius” means
The phrase can refer to two related things: the radius of a rounded-over edge, or the radius of a curve routed into a workpiece. In either case, it describes geometry, not a standard setting shared by all routers. Router speed, cutting depth, and fence position are settings on the tool or setup; the cutter’s profile determines the radius it can produce.
For a round-over bit, the radius usually means the radius of the quarter-circle joining the top and side faces of an edge. A 6 mm radius bit makes a noticeably softer, larger round-over than a 3 mm bit. The bit may also be labeled by diameter, bearing size, or profile, so check the manufacturer’s drawing rather than assuming those dimensions mean the same thing.
For a circular arc, radius means the distance from the circle’s center to the routed curve. A larger radius makes a gentler, flatter arc; a smaller radius makes a tighter curve. A router compass or trammel typically controls this distance by setting the pivot-to-cutter measurement.
How the radius is set
There is generally no control on a handheld router that changes a bit’s cutting radius. Instead, use the appropriate bit or guide arrangement:
- Rounded edge: Select a round-over bit with the required profile radius. A bearing often follows the edge and controls how the cutter meets the workpiece.
- Groove or decorative profile: Select a bit whose cutting edges create the desired curve. The profile drawing is more useful than a generic radius label.
- Large circular arc: Attach a compass guide or trammel and set the pivot-to-bit distance to the desired radius.
- Inside corner: The cutter’s radius sets the smallest inside corner it can leave. A square corner needs a separate operation, such as careful chiseling.
Take the measurement from the point specified by the guide or bit instructions. On a trammel, the effective radius is usually measured from the pivot’s center to the cutter’s centerline, but the exact reference can vary with the jig. Verify it with a scrap cut rather than relying only on a ruler reading.
Choosing a radius for the job
Start with the appearance and function of the finished edge. Small radii preserve a crisp, nearly square look; larger ones feel softer and remove more material. A large round-over can also reduce splinter-prone sharp edges, but it may make a narrow part look bulky or remove details that need to remain visible.
- Furniture edges: A modest round-over is often used to soften a sharp corner while keeping the part’s outline clear.
- Frequently handled parts: A more generous edge can feel more comfortable, subject to the design and required dimensions.
- Thin stock: A large radius may cut through the face or leave little flat surface. Check the bit profile against the actual thickness.
- Templates and circular work: Choose the radius from the drawing or layout, and account for the cutter or guide offset when the guide follows a template.
Do not confuse radius with diameter: diameter is twice the radius. A 12 mm diameter circle has a 6 mm radius. Bit labels may instead describe the bit’s overall diameter or bearing diameter, neither of which necessarily equals the edge radius. If a project calls for a 6 mm round-over, confirm that the bit’s profile radius—not merely its overall width—is 6 mm.
Depth, speed, and test cuts
Radius describes the shape, but it does not tell you how deeply to plunge, how quickly to feed, or what rotational speed to select. Those choices depend on the bit, router, material, and cut. Follow the bit and router instructions, and make multiple shallow passes when the cut is substantial rather than trying to remove all the material at once.
Use a matching scrap piece to check the result. A test reveals whether the profile is the intended size, whether the bearing follows the edge correctly, and whether the setup leaves a step or an unwanted flat. Measure the workpiece after the test, since a round-over reduces the flat face at the edge. For a routed arc, measure the finished curve from its center or compare it with a full-size layout.
Changing depth can alter how much of a shaped bit engages the wood, and therefore can change the apparent profile. It does not turn a round-over bit into a different-radius cutter in a predictable, universal way. Use depth to position the intended profile, not as a substitute for choosing the right bit.
Common problems and safety
A radius that looks wrong often comes from reading the wrong bit dimension, setting a guide from the wrong reference point, or expecting a router’s speed control to change the profile. Check the cutter’s profile diagram and the jig’s measurement instructions. Also verify that the bearing can contact the intended edge and that the workpiece is thick enough for the selected cut.
Secure the workpiece, use a sharp, undamaged bit compatible with the router, and keep hands clear of the cutter. Unplug or otherwise disconnect power before changing bits or making adjustments, following the tool’s instructions. Wear eye and hearing protection and use dust control appropriate to the material. Keep the router stable, and do not force the cut; an unstable setup can cause chatter, burning, or loss of control.
Frequently Asked Questions
How do I adjust the radius on a router?
Usually you do not adjust a radius on the router itself. Change to a bit with the desired cutting profile, or adjust a compass guide’s pivot-to-cutter distance for a circular arc.
Is router radius the same as router bit diameter?
No. Radius is half the diameter of a circle. A bit’s overall diameter is a separate measurement and does not by itself tell you the radius of its rounded cutting profile.
What router bit makes a rounded edge?
A round-over bit is designed to cut a rounded edge. Select it by its stated profile radius and check the profile drawing, bearing, and suitable stock thickness.
How do I route a large-radius curve?
Use a suitable compass guide or trammel, setting the pivot-to-cutter distance to the required radius. Confirm the effective measurement with a layout or scrap cut because jigs can use different reference points.
Can changing router depth change the radius?
Depth changes how much of the bit engages the work and can affect the visible profile, but it does not reliably substitute for a bit with the correct radius.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp