molecalculator

Moles & Molar Mass

RPM to RCF Calculator: Convert Centrifuge Speed

Calculator No. 01-2251 · Updated · Formula and assumptions shown below

Relative centrifugal force 101 ×g
Rotor radius
100 mm
= Rotor radius × 10
Rotational speed
3000 rpm
Set in the form below
Rotor radius
10 cm
Set in the form below
You enter
Rotational speed (rpm), Rotor radius (cm)
You get
Relative centrifugal force (×g), Rotor radius (mm)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Convert centrifuge speed in revolutions per minute (RPM) to relative centrifugal force (RCF, or ×g) by entering RPM and the rotor’s radius in centimeters. The calculator returns the force relative to Earth’s gravity; the result depends on the radius as well as the speed.

Formula

The standard conversion is RCF = 1.118 × 10−5 × r × RPM2, where r is the rotor radius in centimeters and RPM is revolutions per minute. RCF is a multiple of standard gravitational acceleration, so it is commonly written as ×g; it is not a speed or a force expressed in newtons.

The calculator uses the equivalent expression RCF = 1.118 × r × (RPM / 1000)2. Dividing RPM by 1,000 and multiplying the constant by 100,000 gives the same result as the standard coefficient 1.118 × 10−5. The entered radius is in centimeters. The second output converts it to millimeters by multiplying by 10.

  • RCF: relative centrifugal force, expressed as a multiple of g.
  • r: distance in centimeters from the rotation axis to the point of interest in the sample.
  • RPM: rotor speed in revolutions per minute.

The calculator rounds RCF to a whole number for its displayed result. Keep more digits when comparing settings or following a method that specifies a precise force; rounding the displayed answer does not change the underlying relationship.

Worked Example

For the calculator’s default values, RPM = 3,000 and r = 10 cm. Using the calculator’s equivalent form:

RCF = 1.118 × 10 × (3,000 / 1,000)2
= 1.118 × 10 × 32
= 1.118 × 10 × 9
= 100.62 ×g

Rounded to the calculator’s zero decimal places, the result is 101 ×g. The radius conversion is 10 cm × 10 = 100 mm. The radius used here is measured to the relevant point in the rotor; a different sample position produces a different RCF at the same RPM.

Assumptions

  • RPM is the actual rotor speed, not a speed setting expressed in another unit.
  • The radius is measured from the axis of rotation to the point in the sample whose RCF is needed.
  • The formula assumes circular rotation and reports the ideal calculated acceleration relative to standard gravity.
  • It does not account for rotor-specific operating limits, acceleration and braking profiles, or other instrument behavior.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

How RPM and RCF Are Related

RPM describes how quickly a rotor turns. RCF describes the acceleration experienced at a particular distance from its axis, compared with standard gravity. These quantities are connected, but they are not interchangeable: RPM alone does not identify the RCF unless the radius is also known.

Radius matters linearly, while RPM is squared. At a fixed speed, doubling the radius doubles RCF. At a fixed radius, doubling RPM makes RCF four times as large. This squared relationship is why a modest speed change can make a substantial difference to the calculated force.

For example, the default calculation gives 100.62 ×g at 3,000 RPM and 10 cm. At 6,000 RPM with the same radius, the result is 402.48 ×g, four times as high. At 3,000 RPM with a 5 cm radius, it is 50.31 ×g, half the default. These comparisons assume the stated radii and speeds are suitable for the rotor; they are not operating recommendations.

Choosing the Correct Radius

Rotor radius is not necessarily the rotor’s outside diameter or the radius of the rotor body. Use the distance from the axis of rotation to the location within the sample for which the force is required. Rotor documentation or a validated laboratory method may state which radius convention to use.

  • Maximum radius: distance to the farthest relevant point in the sample. A protocol may use this when it specifies maximum RCF.
  • Minimum radius: distance to the nearest relevant point in the sample.
  • Average radius: a representative point between the minimum and maximum radii, used only when the method calls for it.

A sample can extend across a range of radii, so its RCF is not identical at every point. If a procedure says “maximum RCF,” do not substitute an average radius. If it gives an RCF but does not say what radius convention to use, consult the method or rotor documentation rather than guessing.

Using RCF to Find an RPM Setting

If a method specifies RCF and you need the corresponding RPM, rearrange the same formula: RPM = √(RCF / (1.118 × 10−5 × r)), with r in centimeters. For example, for 500 ×g at a 10 cm radius, RPM = √(500 / (1.118 × 10−5 × 10)) ≈ 2,115 RPM. This is a mathematical conversion, not confirmation that a rotor can safely run at that speed.

When transferring a method between rotors, use the radius and RCF convention specified by the method and the relevant rotor information. Do not assume that matching RPM on two rotors gives matching RCF: if their radii differ, the calculated forces differ too.

Common Errors and Limits

  • Entering millimeters as centimeters: convert millimeters to centimeters by dividing by 10. For example, 100 mm is 10 cm, not 100 cm.
  • Using diameter instead of radius: if you have a diameter, divide it by 2 before entering the radius, and make sure the measurement refers to the correct location.
  • Forgetting the square on RPM: the speed term is RPM2. The formula is not proportional to RPM alone.
  • Treating ×g as RPM: RCF and RPM have different meanings and units. A value such as 500 ×g cannot be entered as 500 RPM.
  • Assuming the displayed result is a rotor safety limit: the calculation only converts speed and radius. It does not establish that a rotor, tube, or sample setup is approved for a particular speed.

RCF is an ideal geometric calculation. Rotor design, sample position, acceleration, braking, and the instructions for a specific centrifuge can affect the practical procedure. Use manufacturer-provided specifications and the validated method for actual operation; do not exceed a rotor’s stated limits.

Frequently Asked Questions

How do I calculate RCF from RPM?
Multiply 1.118 × 10−5 by the radius in centimeters and by RPM squared. The result is RCF in ×g.

What radius should I use for an RCF calculation?
Use the distance from the rotation axis to the sample position named by your method, such as the maximum, minimum, or average radius. Check the method or rotor documentation if it does not specify.

Is RCF the same as ×g?
Yes. RCF is conventionally reported as a multiple of standard gravitational acceleration, written ×g. It is not the same unit or quantity as RPM.

Can the same RPM give different RCF values?
Yes. At the same RPM, a rotor with a larger radius produces a larger calculated RCF. The sample’s position within a rotor also matters.

How do I convert RCF back to RPM?
Use RPM = √(RCF / (1.118 × 10−5 × r)), with RCF as a multiple of g and radius in centimeters. Confirm separately that the resulting speed is within the rotor’s permitted operating range.

Why do two calculators give slightly different answers?
They may use different rounded constants, radius conventions, or rounding precision. Confirm the radius and formula used, and compare unrounded values when precision matters.

Related

Formula used
in rpm | Rotational speed | rpm | 3000 | 0
in r | Rotor radius | cm | 10 | 0
out rcf | Relative centrifugal force | ×g | 1.118 * r * (rpm / 1000)^2 | 0
out rad | Rotor radius | mm | r * 10 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →