The S-4-104 rotor radius cannot be stated reliably from the designation alone: the name does not identify a rotor whose dimensions can be confirmed from the information provided. To determine a usable radius, you need the specific manufacturer or equipment model and its rotor drawing or manual; do not treat a guessed number as a verified specification.
Formula
This calculator does not identify the S-4-104 rotor’s radius. It shows how to calculate a related quantity once you have a verified radius from a drawing or manual. Rim speed is the circumference of the rotor at its outer radius multiplied by revolutions per second:
v = 2π × (r / 1000) × (s / 60)
- v is rim speed in metres per second (m/s).
- r is rotor radius in millimetres (mm); dividing by 1000 converts millimetres to metres.
- s is rotational speed in revolutions per minute (rpm); dividing by 60 converts minutes to seconds.
- π is the mathematical constant pi.
The diameter output is d = 2 × r, in millimetres. A rotor’s radius is the distance from its axis of rotation to the point being measured. It is half the diameter only when the diameter and radius refer to the same circular path or feature.
Worked Example
The calculator starts with an illustrative radius of 100 mm and speed of 1,000 rpm. These are example defaults, not verified dimensions or operating specifications for an S-4-104 rotor.
Convert the radius: 100 mm / 1,000 = 0.1 m. Convert the speed: 1,000 rpm / 60 = 16.66667 revolutions per second. Then calculate rim speed: 2 × π × 0.1 m × 16.66667 s−1 ≈ 10.47 m/s. The corresponding diameter is 2 × 100 mm = 200.0 mm.
Assumptions
- The input radius is a verified measurement or specification for the rotor being assessed; the sample default is for demonstrating the arithmetic only.
- The speed is constant and expressed in revolutions per minute.
- Rim speed refers to the circular path at the stated radius. It is not a measurement of fluid flow, rotor performance, or centrifugal force.
- The calculation uses ideal circular geometry and does not account for deformation, vibration, or operating limits.
Why the S-4-104 Radius Needs Verification
Part numbers and short model labels are not universal identifiers. Similar-looking designations can belong to unrelated devices, and a number within a designation may be a series code rather than a dimension. Without an authoritative source tying “S-4-104” to a particular maker, product, and rotor configuration, assigning a radius would risk confusing one component with another.
The exact radius may also depend on what “rotor radius” means in context. A drawing could specify the outside radius, the radius to the centreline of a channel, or a distance to a working surface. These values are not interchangeable. For a rotating assembly, the distance needed for a rim-speed calculation is from the rotation axis to the exact point whose linear speed is relevant.
Look for the full equipment name, manufacturer, revision or part number, and a drawing that labels the measurement. A manual may list rotor dimensions separately from the dimensions of a housing or accessory. If the source gives diameter instead, halve that diameter only after confirming it describes the same circular feature.
How Radius Affects Rotor Speed
At a fixed rotational speed, rim speed rises in direct proportion to radius: doubling the radius doubles the linear speed at the rim. At a fixed radius, doubling revolutions per minute also doubles rim speed. This follows from the distance travelled in one turn, which is the circumference, 2πr.
That relationship is useful for interpreting dimensions, but it does not by itself establish whether a rotor is safe or suitable. Maximum permitted speed depends on the rotor’s design, materials, mounting, balance, and the equipment’s operating instructions. Do not infer a safe speed from a calculated rim speed or from a radius alone.
A common mix-up is radius versus diameter. For example, a measured diameter of 200 mm means a radius of 100 mm. Entering 200 mm as the radius would make the calculated rim speed twice as high as the value based on that diameter. Another frequent error is mixing units: the formula converts millimetres to metres and rpm to revolutions per second explicitly.
Finding and Checking the Specification
Use a source that clearly identifies the exact component. Useful checks include:
- Match the complete model and part designation, not just “S-4-104.”
- Check that the document applies to the relevant revision or configuration.
- Confirm whether the dimension is a radius or diameter, and identify the feature it describes.
- Compare the drawing’s units and dimension labels with any physical measurement.
- Ask the equipment’s responsible technical contact to resolve conflicting or unclear documentation.
A physical measurement can be helpful, but it should not replace a specified operating limit. Measure from the rotation axis to the intended point, account for any hub or shaft geometry, and use suitable measurement methods for the equipment. For operating or maintenance work, follow the equipment documentation and applicable workplace procedures.
Frequently Asked Questions
What is the S-4-104 rotor radius?
The designation alone does not establish a verified radius. Identify the exact equipment and consult its authoritative drawing or manual before using a value.
Is rotor radius half the rotor diameter?
Yes, when both measurements describe the same circular feature. Radius is measured from the centre or rotation axis to the edge; diameter spans the full circle through its centre.
Can I calculate rim speed without knowing the radius?
No. Rim speed depends on both radius and rotational speed. You need a verified radius and a speed in rpm, then apply the formula shown above.
Does the number 104 in S-4-104 mean 104 mm?
Not necessarily. A model designation may encode a series or product identifier rather than a physical dimension. Confirm its meaning in documentation for the specific equipment.
Does a calculated rim speed tell me the rotor’s safe maximum speed?
No. It is a geometric calculation, not a safety rating. Use the manufacturer’s specified limits and operating instructions for the exact rotor and assembly.
Related
Formula used
in r | Rotor radius | mm | 100 | 0 in s | Rotor speed | rpm | 1000 | 0 out v | Rim speed | m/s | 2 * pi * (r / 1000) * (s / 60) | 2 out d | Rotor diameter | mm | 2 * r | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp