molecalculator

Moles & Molar Mass

Specific Enthalpy of Air Calculator & Formula

Calculator No. 01-8369 · Updated · Formula and assumptions shown below

Specific enthalpy 50.62 kJ/kg dry air
Sensible component
25.15 kJ/kg dry air
= 1.006 × Dry-bulb temperature
Latent component
25.48 kJ/kg dry air
= Humidity ratio × (2501 + 1.86 × Dry-bulb temperature)
Dry-bulb temperature
25 °C
Set in the form below
You enter
Dry-bulb temperature (°C), Humidity ratio (kg/kg)
You get
Specific enthalpy (kJ/kg dry air), Sensible component (kJ/kg dry air), Latent component (kJ/kg dry air)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the specific enthalpy of moist air (in kJ/kg of dry air) from the dry-bulb temperature and the humidity ratio (specific humidity). You enter the air temperature in °C and the humidity ratio in kg water per kg dry air; the calculator returns the specific enthalpy, which is the total heat content per unit mass of dry air, including the sensible heat of the air and water vapor and the latent heat of the water vapor.

Formula

The specific enthalpy of moist air is calculated using the standard psychrometric formula:

h = cp,air · t + w · (hfg + cp,vapor · t)

Where:

  • h = specific enthalpy of moist air (kJ/kg dry air)
  • cp,air = specific heat of dry air at constant pressure ≈ 1.006 kJ/(kg·°C)
  • t = dry-bulb temperature (°C)
  • w = humidity ratio, mass of water vapor per mass of dry air (kg/kg)
  • hfg = latent heat of vaporization of water at 0°C ≈ 2501 kJ/kg
  • cp,vapor = specific heat of water vapor at constant pressure ≈ 1.86 kJ/(kg·°C)

The term 1.006·t is the sensible heat of the dry air. The second term w·(2501 + 1.86·t) accounts for the heat in the water vapor: 2501 kJ/kg is the latent heat (energy to evaporate water at 0°C), and 1.86·t is the sensible heat of the vapor above 0°C.

Worked Example

Using the default values: t = 25°C, w = 0.010 kg/kg.

  1. Calculate the sensible component: 1.006 × 25 = 25.15 kJ/kg
  2. Calculate the latent component: 0.010 × (2501 + 1.86 × 25) = 0.010 × (2501 + 46.5) = 0.010 × 2547.5 = 25.475 kJ/kg
  3. Add them: h = 25.15 + 25.475 = 50.625 ≈ 50.63 kJ/kg dry air

The calculator shows 50.63 kJ/kg dry air, matching the manual calculation.

Assumptions

  • The air is a mixture of dry air and water vapor only (no other gases).
  • Both dry air and water vapor behave as ideal gases.
  • The specific heats (1.006 and 1.86) are constant over the temperature range (valid for typical HVAC conditions, roughly 0–60°C).
  • The reference state for enthalpy is 0°C for both dry air and liquid water. This means the enthalpy of dry air at 0°C is 0, and the enthalpy of liquid water at 0°C is 0.
  • The latent heat of vaporization is taken at 0°C (2501 kJ/kg). This is a standard psychrometric convention.

How to Use the Calculator

To use the calculator, you need two inputs:

  • Dry-bulb temperature (°C): the ordinary air temperature measured with a standard thermometer.
  • Humidity ratio (kg/kg): the mass of water vapor per unit mass of dry air. This is also called specific humidity. You can obtain it from a psychrometric chart if you know the relative humidity and temperature, or from a dew-point measurement.

If you don’t have the humidity ratio directly, you can compute it from relative humidity (RH) and temperature using the saturation vapor pressure. For example, at 25°C, the saturation pressure of water is about 3.17 kPa. At 50% RH, the partial pressure of water vapor is 0.5 × 3.17 = 1.585 kPa. The humidity ratio is approximately 0.622 × (pv / (patm – pv)) = 0.622 × (1.585 / (101.325 – 1.585)) ≈ 0.0099 kg/kg. This is close to the default 0.010.

Why Specific Enthalpy Matters

Specific enthalpy is a key property in air conditioning, ventilation, and drying processes. It represents the total energy content of the air per unit mass of dry air. Engineers use it to:

  • Calculate the cooling or heating load in HVAC systems. The change in enthalpy between supply and return air tells you how much heat the system must add or remove.
  • Determine the energy required to humidify or dehumidify air. For example, adding moisture increases the latent heat component.
  • Evaluate the performance of cooling towers, evaporative coolers, and dryers.
  • Plot processes on a psychrometric chart, where enthalpy lines are diagonal.

For instance, if you have 1 kg/s of air flowing through a heater, and the enthalpy increases from 40 kJ/kg to 60 kJ/kg, the heating power needed is (60 – 40) × 1 = 20 kW.

Common Mistakes and Misconceptions

  • Using the wrong mass basis: Specific enthalpy of moist air is always per kg of dry air, not per kg of moist air. The humidity ratio is defined on a dry-air basis. If you use total mass, the numbers will be off.
  • Ignoring the latent heat: Some simple formulas treat air as dry, but moisture adds significant energy. At 25°C and 50% RH, the latent component is about half of the total enthalpy.
  • Unit mix-ups: Ensure temperature is in °C for this formula. If you have temperature in Kelvin, subtract 273.15 first. The humidity ratio must be in kg/kg, not g/kg (divide by 1000).
  • Confusing enthalpy with internal energy: Enthalpy includes the pV work, but for ideal gases at constant pressure, the difference is small. The formula above is specifically for enthalpy.
  • Assuming constant specific heats over wide ranges: The formula is accurate for typical atmospheric conditions (0–60°C). For very high temperatures (e.g., combustion gases), the specific heats vary and you need more complex equations.

Limitations of the Formula

The simple linear formula works well for air conditioning and ventilation design, but it has limitations:

  • It assumes ideal gas behavior, which is excellent at atmospheric pressure and typical temperatures.
  • It ignores the effect of pressure on enthalpy. For most HVAC applications at near-atmospheric pressure, this is negligible. At very high pressures, you would need real-gas corrections.
  • The specific heat of water vapor (1.86 kJ/kg·°C) is an average value. The actual value varies slightly with temperature, but the error is small.
  • For sub-zero temperatures, the formula does not account for the latent heat of fusion (ice formation). If you are dealing with snow or ice, a more detailed model is needed.

For most engineering work, the formula is accurate to within 0.5% for temperatures between 0 and 50°C and humidity ratios up to 0.03 kg/kg.

Frequently Asked Questions

What is the difference between specific enthalpy and enthalpy?

Enthalpy (H) is the total heat content of a system, measured in kJ. Specific enthalpy (h) is enthalpy per unit mass, measured in kJ/kg. In air conditioning, we use specific enthalpy because the amount of air varies, and we want a property that is independent of the total mass.

How do I find the humidity ratio if I only know relative humidity?

You need the saturation pressure of water at the given temperature. The humidity ratio is w = 0.622 × (RH × psat) / (patm – RH × psat), where RH is in fraction (e.g., 0.5 for 50%), psat is the saturation pressure, and patm is atmospheric pressure. Many online calculators and psychrometric charts can do this for you.

Can I use this calculator for air at high altitudes?

Yes, with a small error. The formula does not depend on atmospheric pressure directly. However, the humidity ratio you input must be correct for that pressure. At altitude, the same relative humidity corresponds to a lower humidity ratio because the total pressure is lower. So, as long as you input the correct w, the enthalpy calculation is accurate.

Why is the latent heat of vaporization 2501 kJ/kg in the formula?

This is the latent heat of vaporization of water at 0°C. In psychrometrics, the reference state is 0°C for liquid water. The energy to evaporate water at 0°C is 2501 kJ/kg. When water evaporates at a higher temperature, the latent heat is slightly less, but the sensible heat of the vapor above 0°C compensates, so the formula with 2501 and 1.86·t gives the same result as using the actual latent heat at that temperature.

What is a typical specific enthalpy for indoor air?

For comfortable indoor conditions of 22°C and 50% RH, the humidity ratio is about 0.0082 kg/kg. Using the formula: h = 1.006×22 + 0.0082×(2501 + 1.86×22) = 22.13 + 0.0082×2541.92 = 22.13 + 20.84 = 42.97 kJ/kg dry air. So, around 43 kJ/kg is typical.

Related

Formula used
in t | Dry-bulb temperature | °C | 25 | -40 | 60
in w | Humidity ratio | kg/kg | 0.010 | 0 | 0.200
out h | Specific enthalpy | kJ/kg dry air | 1.006 * t + w * (2501 + 1.86 * t) | 2
out hsi | Sensible component | kJ/kg dry air | 1.006 * t | 2
out hli | Latent component | kJ/kg dry air | w * (2501 + 1.86 * t) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →