molecalculator

Moles & Molar Mass

Specific Gravity of Sodium Hydroxide: Calculator

Calculator No. 01-1198 · Updated · Formula and assumptions shown below

Estimated specific gravity 1.431
Estimated solution density
1.431 g/mL
= Estimated specific gravity
NaOH concentration by mass
50 %
Set in the form below
Solution temperature
20 °C
Set in the form below
You enter
NaOH concentration by mass (%), Solution temperature (°C)
You get
Estimated specific gravity, Estimated solution density (g/mL)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates the specific gravity of an aqueous sodium hydroxide solution from its NaOH mass percentage and temperature. Enter the concentration and temperature to get an estimated density and specific gravity; the result is a reference estimate, not a substitute for a product specification or measurement.

Formula

Specific gravity is the density of the solution divided by the density of water at the reference temperature. For this estimate, the concentration-based approximation is multiplied by a small temperature correction:

SG ≈ [1.000 + 0.00752w + 0.000022w²] × [1 − 0.00035(t − 20)]

  • SG is estimated specific gravity, dimensionless.
  • w is sodium hydroxide concentration in percent by mass, from 0 to 100.
  • t is solution temperature in °C; this approximation is limited to 0–100 °C.

The density output uses the approximation that water has a density of 1.000 g/mL, so its numerical value in g/mL is the same as the calculated SG. This is a convenient reference approximation, not a high-precision conversion. Specific gravity conventionally compares densities at stated temperatures; values may differ slightly depending on the water reference temperature and the source’s measurement convention.

Worked Example

Using the default entries, the solution is 50% NaOH by mass at 20 °C.

Concentration term = 1.000 + (0.00752 × 50) + (0.000022 × 50²)
= 1.000 + 0.37600 + 0.055000
= 1.43100

Temperature term = 1 − [0.00035 × (20 − 20)] = 1.00000

Estimated SG = 1.43100 × 1.00000 = 1.431 (rounded to three decimal places). Estimated density = 1.431 g/mL under the calculator’s water-density approximation.

Assumptions

  • The liquid is a sodium hydroxide solution in water, and the concentration is percent by mass, not by volume.
  • The approximation is intended for ordinary aqueous solutions over the calculator’s stated input ranges. It does not account for other dissolved substances.
  • The density-to-SG conversion treats water as 1.000 g/mL; exact reference values depend on temperature and convention.
  • Temperature correction is approximate. Use a reliable density table, supplier specification, or measurement when precision matters.

What Specific Gravity Means for Sodium Hydroxide

Specific gravity (SG), also called relative density, is a ratio and therefore has no units. An SG of 1.431 means the solution is about 1.431 times as dense as the water reference used for the comparison. It does not mean that the solution is 143.1% NaOH. Concentration and specific gravity are related, but they describe different properties.

Sodium hydroxide, NaOH, is a strongly alkaline, highly soluble solid. When dissolved in water, the resulting solution is denser than water, and its density generally increases as the mass fraction of NaOH increases. Temperature matters too: liquids usually expand as they warm, lowering density. The calculator accounts for that trend approximately, but the relationship is not a universal physical law.

Concentration, Density, and Temperature

A label stating “50% NaOH” normally means 50% by mass: 50 g of sodium hydroxide in 100 g of finished solution. It does not mean 50 g added to 100 g of water. That distinction affects the concentration and therefore the expected density. For an actual commercial product, check how the concentration is specified and use its documentation.

The estimate gives about 1.431 at 50% and 20 °C. A change in temperature shifts the estimate slightly, while a change in concentration can shift it substantially. For example, a dilute solution should have a specific gravity closer to 1 than a concentrated solution. Do not use this approximate equation to identify an unknown liquid: different substances and mixtures can have similar densities.

Temperature should refer to the solution at the time its density is being considered, not necessarily the room or storage temperature. Dissolving NaOH in water releases heat, so a newly prepared solution may be warmer than its surroundings. For accurate work, allow the sample and measurement method to reach the specified temperature according to an approved lab method.

When to Use the Estimate

This calculator is useful for a quick plausibility check or for understanding how concentration and temperature affect SG. It can also help explain why a fixed volume of concentrated caustic solution weighs more than the same volume of water. It is not suitable for exact mass-volume conversions unless the density is confirmed for the exact concentration and temperature.

  • Use mass percentage as the input. Do not enter molarity, normality, or a volume percentage as though it were mass percentage.
  • Use the temperature of the solution and stay within the calculator’s range.
  • For production, analytical, or process calculations, consult a validated density table or measure the sample with an appropriate method.
  • Keep significant figures consistent with the quality of the concentration and temperature data. Three displayed decimals do not imply that the estimate is accurate to three decimals.

Limits and Common Misconceptions

The equation is a simplified empirical approximation. Real density data can vary with concentration, temperature, and measurement conventions; the equation may diverge from reliable reference data, particularly near the ends of its range. It should not be extrapolated beyond 0–100% concentration or 0–100 °C. A value outside those ranges is rejected rather than treated as dependable.

Specific gravity is not the same as “percent caustic,” and it cannot by itself establish a solution’s identity or purity. Nor is a density estimate automatically a safe handling guide. Sodium hydroxide is corrosive; its solutions can cause severe burns and eye damage. For any bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. Use appropriate protective measures and never rely on this calculator to replace a hazard assessment.

Frequently Asked Questions

What is the specific gravity of sodium hydroxide?
There is no single value for sodium hydroxide solution: SG depends mainly on concentration and also on temperature. The calculator estimates it from mass percentage and temperature; pure solid NaOH is not described by an aqueous-solution concentration.

What is the specific gravity of 50% sodium hydroxide?
At 20 °C, this calculator estimates 1.431, corresponding to an approximate density of 1.431 g/mL. Use a product specification or validated reference data for exact values.

Is specific gravity the same as density?
No. Density has units, such as g/mL; specific gravity is a ratio of the sample’s density to a reference density and has no units. They have the same numerical value only when the chosen reference density is 1.000 g/mL.

Does temperature affect sodium hydroxide specific gravity?
Yes. A solution’s density generally decreases as it warms, so its specific gravity also changes. Always compare values at the same stated temperature and reference convention.

Can I use SG to find NaOH concentration?
Only with a suitable, validated density-concentration table or calibration for the relevant temperature and solution composition. This calculator runs in the other direction and is only an estimate; SG alone is not a reliable concentration test.

Related

Formula used
in wt | NaOH concentration by mass | % | 50 | 0 | 100
in t | Solution temperature | °C | 20 | 0 | 100
out sg | Estimated specific gravity | - | (1.000 + 0.00752 * wt + 0.000022 * wt ^ 2) * (1 - 0.00035 * (t - 20)) | 3
out rho | Estimated solution density | g/mL | sg | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →