This calculator converts a drug dose prescribed in micrograms per kilogram per hour (mcg/kg/hr) into an infusion rate in milliliters per hour (mL/hr). You enter the patient’s weight, the dose, and the drug concentration (amount of drug per volume of fluid), and it returns the pump rate you need to set. It is for general concentration arithmetic and study purposes only — it must not be used for clinical or medication dosing.
Formula
The conversion is straightforward once all units match. The prescribed dose is in micrograms (mcg), but drug concentrations are usually given in milligrams per milliliter (mg/mL). Since 1 mg = 1000 mcg, you first convert the dose to mg/hr:
Dose (mg/hr) = Dose (mcg/kg/hr) × Weight (kg) ÷ 1000
Then divide by the concentration to get the volume rate:
Infusion rate (mL/hr) = Dose (mg/hr) ÷ Concentration (mg/mL)
Where:
- Weight – patient mass in kilograms (kg)
- Dose – prescribed amount in micrograms per kilogram per hour (mcg/kg/hr)
- Concentration – amount of drug in each milliliter of solution (mg/mL)
- Infusion rate – pump setting in milliliters per hour (mL/hr)
Worked Example
Using the default values: weight = 70 kg, dose = 5 mcg/kg/hr, concentration = 1 mg/mL.
Step 1: Convert the dose to mg/hr:
5 mcg/kg/hr × 70 kg = 350 mcg/hr
350 mcg/hr ÷ 1000 = 0.35 mg/hr
Step 2: Divide by the concentration:
0.35 mg/hr ÷ 1 mg/mL = 0.35 mL/hr
The calculator shows 0.35 mL/hr, rounded to two decimals. If the concentration were 0.5 mg/mL, the rate would double to 0.70 mL/hr.
Assumptions
- The drug concentration is uniform throughout the infusion fluid.
- 1 mg = 1000 mcg exactly.
- The patient’s weight is constant during the infusion.
- The pump delivers a continuous, accurate flow rate.
- No dead volume or line priming is considered.
When to Use This Conversion
This calculation appears in pharmacology and nursing math problems, and in preparing continuous infusions in laboratory or research settings. It is used whenever a drug is ordered as a weight-based hourly dose but the infusion pump delivers a volume per hour. The same arithmetic applies to any substance given by continuous IV infusion, from vasopressors to sedatives, but the numbers here are for educational practice only.
How to Read the Result
The result is the pump rate in mL/hr. If the answer is very small (like 0.35), it means the drug is concentrated and only a tiny volume is needed per hour. If the answer is large (like 50 mL/hr), the solution is dilute or the dose is high. Always check that the result is within the pump’s delivery range (typically 0.1–999 mL/hr) and that the total volume over 24 hours fits in the bag or syringe being used.
Common Mistakes
- Forgetting the 1000 conversion – mixing mcg and mg without dividing by 1000 gives a rate 1000 times too high.
- Using the wrong concentration – concentration is mg per mL, not mg per bag. If a 100 mL bag contains 100 mg, the concentration is 1 mg/mL, not 100 mg/mL.
- Weight units – pounds must be converted to kg (1 lb = 0.4536 kg). Entering pounds as kg overestimates the dose.
- Rounding too early – rounding intermediate values can shift the final rate. Keep extra digits until the end.
Choosing the Right Concentration
Concentration is usually fixed by the drug preparation or the pharmacy. In a study or lab setting, you may choose it to make the infusion rate convenient. For example, if you want a 70 kg patient to receive 5 mcg/kg/hr and you want a rate of 10 mL/hr, you would prepare a concentration of:
0.35 mg/hr ÷ 10 mL/hr = 0.035 mg/mL
That means 3.5 mg of drug in 100 mL of fluid. Always prepare solutions according to the drug’s solubility and stability, and follow the safety data sheet (SDS) and your supervisor.
Limits of the Formula
This formula assumes the drug is evenly mixed and the pump is accurate. It does not account for: drug lost in tubing, changes in patient weight, or the drug’s half-life and steady-state kinetics. It is a pure arithmetic conversion, not a pharmacokinetic model. In real clinical practice, a pharmacist or clinician verifies the calculation and the pump is double-checked. For any actual medication use, consult a licensed professional.
Frequently Asked Questions
What if my concentration is in mcg/mL instead of mg/mL?
You can enter it directly if you adjust the formula: rate (mL/hr) = dose (mcg/kg/hr) × weight (kg) ÷ concentration (mcg/mL). The calculator above expects mg/mL, so if your concentration is 500 mcg/mL, convert to 0.5 mg/mL before entering.
How do I convert from mL/hr back to mcg/kg/hr?
Reverse the steps: multiply the rate (mL/hr) by the concentration (mg/mL) to get mg/hr, multiply by 1000 to get mcg/hr, then divide by the weight in kg. For example, 0.35 mL/hr × 1 mg/mL = 0.35 mg/hr = 350 mcg/hr ÷ 70 kg = 5 mcg/kg/hr.
Why do I need the patient’s weight?
The dose is ordered per kilogram of body weight, so a heavier patient needs more drug per hour to achieve the same mcg/kg/hr. Without weight, you only have the total hourly dose, not the rate.
What if the dose is given per minute instead of per hour?
Multiply the per-minute dose by 60 to get per hour first. For example, 0.1 mcg/kg/min = 6 mcg/kg/hr. Then use the same conversion.
Is this calculator safe to use for real patients?
No. This page is for educational and planning arithmetic only. Medication errors can be fatal; always have a second person verify calculations and use only hospital-approved protocols and devices.