The combustion of one mole of benzene (C6H6) releases approximately 3267 kJ of heat at 25 °C and 1 atm, producing 6 moles of carbon dioxide and 3 moles of liquid water. This value is the standard enthalpy of combustion (ΔcH°) for benzene, a key figure in thermochemistry and fuel calculations.
Formula
The balanced combustion equation for benzene is:
C6H6(l) + 7.5 O2(g) → 6 CO2(g) + 3 H2O(l) ΔcH° = −3267 kJ/mol
Here, ΔcH° is the standard molar enthalpy of combustion (kJ/mol), the heat released when one mole of liquid benzene burns completely in oxygen at 25 °C and 1 atm, with products in their standard states (CO2 gas, H2O liquid). The negative sign indicates an exothermic reaction (heat is released).
Worked Example
Using the calculator defaults: 1 mole of benzene (molar mass 78.11 g/mol).
- Heat released = 1 mol × 3267 kJ/mol = 3267 kJ (rounded to 1 decimal).
- Mass of benzene = 1 mol × 78.11 g/mol = 78.11 g.
- CO2 produced = 1 mol × 6 = 6 mol.
- H2O produced = 1 mol × 3 = 3 mol.
So burning 78.11 g of benzene releases 3267 kJ and forms 6 mol CO2 and 3 mol H2O.
Assumptions
- Benzene is in the liquid state at 25 °C (its normal boiling point is 80.1 °C).
- Products are CO2(g) and H2O(l) at 25 °C and 1 atm.
- Complete combustion occurs (no CO or soot).
- The value 3267 kJ/mol is the standard enthalpy of combustion, which can vary slightly with temperature and pressure, but the standard value is widely accepted.
Why This Value Matters
The enthalpy of combustion is a direct measure of the energy stored in a fuel. Benzene’s value (3267 kJ/mol) is relatively high compared to many simple hydrocarbons, reflecting its stable aromatic ring and high carbon-to-hydrogen ratio. For context, octane (a component of gasoline) has ΔcH° ≈ −5470 kJ/mol, but that is per mole of a larger molecule; on a per-gram basis, benzene releases about 41.8 kJ/g, while octane releases about 47.8 kJ/g. This difference is why gasoline is more energy-dense by mass than benzene.
In industrial settings, benzene is often used as a solvent and a precursor for chemicals like styrene and phenol. Its combustion heat is used in energy balance calculations for processes that burn benzene as a fuel or as a waste stream.
How to Use the Calculator
Enter any two of the three inputs (mass, molar mass, or amount in moles) to calculate the heat released and the product amounts. The calculator uses the stoichiometry of the balanced equation: 1 mol benzene → 6 mol CO2 and 3 mol H2O. If you enter a mass, the calculator converts it to moles using the molar mass you provide (default 78.11 g/mol for benzene). The heat output is simply moles × 3267 kJ.
The calculator is useful for:
- Estimating the energy released when a given mass of benzene is burned (e.g., in a calorimeter).
- Calculating the amount of CO2 produced for environmental impact assessments.
- Checking stoichiometric ratios for combustion reactions in lab experiments.
Common Mistakes and Misconceptions
- Using the wrong state of water: The standard enthalpy of combustion often assumes liquid water as a product. If water vapor is produced, the heat released is lower by the enthalpy of vaporization (about 44 kJ/mol water). For 3 mol water, that’s about 132 kJ less.
- Confusing per mole with per gram: The value 3267 kJ is per mole of benzene, not per gram. Always convert mass to moles first.
- Ignoring the sign: ΔcH° is negative (−3267 kJ/mol), but many people say “releases 3267 kJ” without the minus. In calculations, keep the sign to get correct energy balances.
- Rounding molar mass: Using 78 g/mol instead of 78.11 g/mol introduces a 0.14% error, which can matter in precise work.
Safety and Practical Notes
Benzene is a known carcinogen and a flammable liquid. Any combustion experiment must be performed in a fume hood with proper personal protective equipment, following your lab’s method and the safety data sheet (SDS). The heat released is substantial; a mole of benzene (78 g) can raise the temperature of about 780 g of water by 100 °C (if perfectly transferred). In practice, calorimetry measures temperature changes to determine the heat of combustion, but you should never attempt to burn benzene outside a controlled apparatus.
Also note that incomplete combustion produces carbon monoxide and soot, which are hazardous. The calculator assumes complete combustion, so real-world yields may be lower.
Frequently Asked Questions
What is the heat of combustion of benzene per gram?
Divide the molar heat by the molar mass: 3267 kJ/mol ÷ 78.11 g/mol ≈ 41.8 kJ/g. This is lower than gasoline (about 47 kJ/g), which is why benzene is not a common motor fuel.
Why is the enthalpy of combustion negative?
By convention, exothermic reactions (those that release heat to the surroundings) have negative enthalpy changes. The products (CO2 and H2O) are more stable (lower energy) than the reactants, so the difference is released as heat.
How does temperature affect the heat of combustion?
The standard value is at 25 °C. At other temperatures, the heat of combustion changes by the difference in heat capacities of reactants and products. For most fuels, the variation is small (a few kJ/mol per 100 °C), so the standard value is a good approximation for typical lab conditions.
Can I use this calculator for other hydrocarbons?
No, the calculator is specific to benzene because it uses the fixed ΔcH° value of 3267 kJ/mol and the stoichiometry 6:3 for CO2:H2O. For other fuels, you would need their respective enthalpy values and balanced equations.
What is the difference between enthalpy of combustion and heat of reaction?
Enthalpy of combustion is a special case of heat of reaction where the reaction is complete oxidation with oxygen. It is always exothermic. Heat of reaction can be endothermic or exothermic and applies to any chemical reaction.