molecalculator

Moles & Molar Mass

Thermal Expansion Calculator: Worked Example

Calculator No. 01-3400 · Updated · Formula and assumptions shown below

Change in length 1.200 mm
Final length
2.00120 m
= Initial length + Initial length × Linear expansion coefficient × Temperature change
Initial length
2 m
Set in the form below
Linear expansion coefficient
0.000012 1/°C
Set in the form below
You enter
Initial length (m), Linear expansion coefficient (1/°C), Temperature change (°C)
You get
Change in length (mm), Final length (m)
Rounding
3 dp · 5 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A thermal expansion calculator estimates how much a solid’s length changes when its temperature changes: enter its initial length, expansion coefficient, and temperature change to calculate the increase or decrease. For example, a 2.00 m steel bar heated by 50 °C expands by about 1.20 mm if its linear expansion coefficient is 12 × 10⁻⁶ °C⁻¹.

Formula

For a small, uniform temperature change, linear thermal expansion is calculated with ΔL = αL₀ΔT. The final length is Lf = L₀ + ΔL. The calculator reports the change in millimetres and the final length in metres.

  • ΔL is the length change, in metres before converting to millimetres.
  • α is the material’s linear expansion coefficient, in °C⁻¹. Its numerical value is the same when expressed per kelvin (K⁻¹), because a temperature interval of 1 °C equals an interval of 1 K.
  • L₀ is the initial length, in metres.
  • ΔT is final temperature minus initial temperature, in °C. It is negative when the material cools.
  • Lf is the estimated final length, in metres.

The output conversion is explicit: multiply the length change in metres by 1,000 to get millimetres. The coefficient depends on the material and, to some extent, temperature; use a suitable tabulated or manufacturer-specified value for the material and temperature range rather than treating the example coefficient as universal.

Worked Example

Use the calculator’s default values: an initial length of 2 m, a linear expansion coefficient of 0.000012 °C⁻¹, and a temperature increase of 50 °C.

  1. Calculate the change in length: ΔL = αL₀ΔT = 0.000012 × 2 × 50 = 0.0012 m.
  2. Convert the change to millimetres: 0.0012 m × 1,000 mm/m = 1.2 mm, or 1.200 mm to the calculator’s three decimal places.
  3. Calculate final length: Lf = 2 + 0.0012 = 2.00120 m.

The positive result means the bar gets longer as it warms. If the same bar instead cooled by 50 °C, ΔT would be −50 °C and the calculated length change would be −1.200 mm, indicating contraction under the same simplified assumptions.

Assumptions

  • The object is a solid with a uniform temperature and a consistent linear expansion coefficient over the stated temperature interval.
  • The object can expand freely along the measured direction; it is not constrained by fasteners, supports, or adjoining materials.
  • The change is small enough for the linear approximation ΔL = αL₀ΔT to be appropriate.
  • The input coefficient is applicable to the material’s composition and temperature range. The example uses 12 × 10⁻⁶ °C⁻¹ as a representative steel value, not a universal value for every steel.

How Thermal Expansion Works

Heating generally increases the average spacing between atoms in a solid, so its dimensions increase. Cooling generally reduces that spacing and contracts the object. The coefficient α describes the fractional length change per degree: a coefficient of 12 × 10⁻⁶ °C⁻¹ corresponds to a change of roughly 12 micrometres per metre for each degree of warming, within the range where that coefficient is a good approximation.

Thermal expansion is usually discussed in three forms. Linear expansion concerns one dimension, such as the length of a bar. Area expansion concerns a surface, and volume expansion concerns three-dimensional volume. For an isotropic solid—a material with the same properties in every direction—and a small temperature change, the area coefficient is approximately 2α and the volume coefficient approximately 3α. Those approximations do not automatically apply to anisotropic materials, whose expansion differs by direction.

When to Use This Calculation

Use the linear formula for a first estimate of the length change of a bar, rail, pipe, wire, or similar solid when its temperature changes. Engineers account for expansion when designing clearances, joints, supports, and assemblies. The result can show whether a millimetre-scale movement is negligible or needs to be accommodated, but it is not by itself a complete design check.

For a real design, identify the material accurately, determine the expected minimum and maximum temperatures, and check whether the part is restrained. If neighbouring components expand by different amounts, their relative movement may matter more than either component’s expansion alone. A constrained object can develop stress instead of freely changing length; this calculator does not calculate that stress or determine whether a component will buckle, crack, or yield.

Common Errors and Limits

  • Mixing length units: this calculator expects metres. Convert millimetres to metres by dividing by 1,000 before entering the initial length.
  • Using the wrong temperature difference: enter final temperature minus initial temperature, not an absolute temperature. A rise from 20 °C to 70 °C is ΔT = 50 °C.
  • Confusing coefficient units: the coefficient is per degree, not a percentage. A value of 12 × 10⁻⁶ °C⁻¹ is 0.000012 °C⁻¹.
  • Assuming all metals share one coefficient: different materials—and different grades or conditions of the same material—can expand differently. Values can also vary with temperature.
  • Ignoring restraint or direction: the simple equation predicts free linear movement, not the forces or deformation in a constrained assembly or an anisotropic material.

The formula is a useful approximation when α is effectively constant over the interval. If the coefficient changes substantially with temperature, a more accurate estimate uses temperature-dependent data and integrates the coefficient across the temperature range. Large temperature excursions, phase changes, composites, and nonuniform heating may require a material-specific model instead.

Frequently Asked Questions

What is the thermal expansion formula?
For linear expansion, use ΔL = αL₀ΔT. Multiply the initial length by the material’s linear expansion coefficient and the temperature change.

How much does a 2 m steel bar expand when heated by 50 °C?
Using α = 12 × 10⁻⁶ °C⁻¹, the estimated increase is 0.0012 m, or 1.2 mm. The exact result depends on the steel and the coefficient appropriate to its temperature range.

Should I use Celsius or kelvin?
Either is suitable for a temperature difference. A change of 50 °C is equal in size to a change of 50 K, so the coefficient’s numerical value per °C equals its value per K.

Does thermal expansion depend on the object’s original length?
Yes. For the same material and temperature change, the linear formula predicts that a longer object changes length in direct proportion to its initial length.

Does this calculator work for liquids or gases?
No. It estimates linear expansion of a solid. Liquids and gases are generally described by volume changes and require an appropriate volumetric coefficient or a different physical model.

Related

Formula used
in l | Initial length | m | 2 | 0
in a | Linear expansion coefficient | 1/°C | 0.000012 | 0
in dt | Temperature change | °C | 50 | -273.15
out dl | Change in length | mm | l * a * dt * 1000 | 3
out lf | Final length | m | l + l * a * dt | 5

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →