molecalculator

Moles & Molar Mass

Thermal Expansion Coefficient Formula and Calculator

Calculator No. 01-3403 · Updated · Formula and assumptions shown below

Average linear expansion coefficient 2.400 × 10−5 K^-1
Coefficient
24.00 µm/(m·K)
= Average linear expansion coefficient × 1000000
Original length
1 m
Set in the form below
Length change
0.0012 m
Set in the form below
You enter
Original length (m), Length change (m), Temperature change (K)
You get
Average linear expansion coefficient (K^-1), Coefficient (µm/(m·K))
Rounding
6 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The thermal expansion coefficient calculator finds a material’s average linear expansion coefficient from its original length, temperature change, and length change. Enter those three values in SI units to get the coefficient in reciprocal kelvins (K−1); the formula also applies to temperature differences in degrees Celsius.

Formula

The average linear thermal expansion coefficient is the change in length divided by the original length and the temperature change:

α = ΔL / (Li × ΔT)

  • α is the average linear expansion coefficient, in K−1.
  • ΔL is the length change, in metres (m).
  • Li is the original length, in metres (m).
  • ΔT is the temperature change, in kelvins (K). For a temperature difference, 1 K has the same size as 1 °C.

The calculator’s second output converts the result to µm/(m·K), also commonly written as parts per million per kelvin (ppm/K). The conversion is α × 1,000,000 because 1 µm per metre equals 10−6.

Worked Example

Using the defaults, a 1 m sample lengthens by 0.0012 m when its temperature rises by 50 K:

α = ΔL / (Li × ΔT)

α = 0.0012 m / (1 m × 50 K) = 0.000024 K−1

To express this in micrometres per metre per kelvin:

0.000024 K−1 × 1,000,000 = 24.00 µm/(m·K)

The calculator therefore reports 0.000024 K−1, or 24.00 µm/(m·K).

Assumptions

  • The measured length change is caused by the stated temperature change; other effects such as mechanical loading are negligible.
  • The coefficient is an average over the temperature interval, not necessarily a constant at every temperature.
  • The sample’s measurement direction and conditions are consistent across the interval.

What the Coefficient Describes

Materials expand or contract as temperature changes because their atoms vibrate more strongly at higher temperatures, shifting the average spacing between them. The linear coefficient describes fractional length change per unit temperature change. A coefficient of 24 µm/(m·K), for example, means a one-metre length changes by about 24 micrometres for each kelvin of temperature increase, under the conditions represented by that coefficient.

The equation is a rearrangement of the approximate engineering relation ΔL = αLiΔT. It is useful for estimating dimensional changes in rods, rails, machine parts, containers, and structural components. A positive ΔT and positive ΔL produce a positive coefficient. Cooling usually gives negative ΔT and negative ΔL; their ratio still gives a positive coefficient for an ordinary material that contracts on cooling.

Linear, Area, and Volume Expansion

This calculator finds the linear coefficient, which applies to length change along one direction. It should not be confused with area or volume expansion coefficients. For an isotropic solid—one whose properties are the same in every direction—and a modest temperature interval, area expansion is approximately twice the linear coefficient, while volume expansion is approximately three times it:

  • Linear: ΔL/Li ≈ αΔT
  • Area: ΔA/Ai ≈ 2αΔT
  • Volume: ΔV/Vi ≈ 3αΔT

These approximations assume small dimensional changes and isotropic behavior. They are not reliable substitutes for direction-specific or temperature-dependent data in anisotropic materials, composites, or demanding designs. For a liquid, expansion is generally described by a volumetric coefficient rather than a linear one.

Using the Result and Choosing Inputs

Use consistent units: the calculator expects both lengths in metres and the temperature difference in kelvins. A change from 20 °C to 70 °C is ΔT = 50 °C, which is also 50 K; do not convert a temperature difference by adding 273.15. That offset is used only when converting an absolute temperature, not a difference.

If you are measuring a sample, determine its initial length and its change in length over a known temperature interval. The change may be calculated as final length minus initial length. Keep the sign if you want to represent contraction as negative; for the average coefficient, using signed changes consistently gives the material’s signed response. When you only need the magnitude, report that convention clearly.

To estimate a change from a known coefficient, rearrange the formula: ΔL = αLiΔT. For instance, if a component’s coefficient is 12 µm/(m·K), its length is 2 m, and it warms by 30 K, the estimated expansion is 12 × 2 × 30 = 720 µm, or 0.72 mm. This is an estimate; actual values depend on the material, temperature range, and constraints.

Limits and Common Mistakes

  • Mixing units: entering millimetres as though they were metres changes the calculated result by a factor of 1,000 if only one length value is mishandled. Convert both lengths to metres first.
  • Using absolute temperatures: ΔT is the difference between two temperatures. A 50 °C rise is 50 K, not 323.15 K.
  • Ignoring the temperature range: coefficients can vary with temperature. A single average may not predict expansion accurately across a very broad range or near a phase transition.
  • Confusing free and constrained expansion: the formula estimates a free dimensional change. If a part is restrained, thermal stresses can develop and require a mechanical analysis.
  • Rounding too early: retain the measured values’ useful precision during calculation, then round the reported result to match the quality of the measurements.

For engineering design, use a coefficient appropriate to the specific material grade, direction, and temperature range, and verify tolerances with suitable material data. Measurement uncertainty also matters: if ΔL is very small compared with instrument resolution, the calculated coefficient may be unreliable even when the arithmetic is correct.

Frequently Asked Questions

What is the formula for the coefficient of thermal expansion?
For average linear expansion, α = ΔL/(LiΔT), where ΔL is the length change, Li is the starting length, and ΔT is the temperature difference.

What are the units of thermal expansion coefficient?
The SI unit is K−1. It is also often given as µm/(m·K) or ppm/K; these numerical forms are equivalent after multiplying K−1 by one million.

Is a temperature change in Celsius equal to one in kelvins?
Yes. A difference of 1 °C equals a difference of 1 K. The Celsius-to-kelvin offset of 273.15 applies to absolute temperatures, not temperature differences.

Can the coefficient be negative?
Some materials can contract as they warm over certain temperature ranges, giving a negative coefficient. For ordinary expansion, signed length and temperature changes usually give a positive result.

Does this formula work for volume expansion?
No. It calculates linear expansion. For an isotropic solid and a small temperature interval, the volume coefficient is approximately three times the linear coefficient, but direct volumetric data are preferable when accuracy matters.

Related

Formula used
in li | Original length | m | 1 | 0
in dl | Length change | m | 0.0012 | 0
in dt | Temperature change | K | 50 | 0
out alpha | Average linear expansion coefficient | K^-1 | dl / (li * dt) | 6
out ppm | Coefficient | µm/(m·K) | alpha * 1000000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →