The thermal expansion equation for a cylinder gives how its dimensions change when its temperature changes: for a freely expanding, isotropic solid, each linear dimension changes by ΔL = αL₀ΔT. Enter the cylinder’s original dimensions, material’s linear expansion coefficient, and temperature change to calculate its new length, diameter, radius, and volume.
Formula
For a freely expanding cylinder made of a uniform, isotropic material, the basic linear thermal-expansion equation is:
ΔL = αL₀ΔT, or equivalently, L = L₀(1 + αΔT).
- ΔL is the change in a length, in metres (m).
- L₀ is the original length, diameter, or radius, in metres.
- L is that dimension after the temperature change, in metres.
- α is the material’s linear coefficient of thermal expansion, in inverse kelvins (1/K). It describes fractional length change per kelvin near the stated temperature range.
- ΔT is final temperature minus initial temperature, in kelvins (K). A temperature difference of 1 K has the same size as a difference of 1 °C.
Because the cylinder’s length and diameter each scale by the same factor, its radius scales by that factor too. For a cylinder with original radius r₀ and length L₀, the initial volume is V₀ = πr₀²L₀. The calculator uses V = V₀(1 + αΔT)³, or, using diameter d₀, V = π(d₀/2)²L₀(1 + αΔT)³. This is the finite, uniform-scaling result based on a constant α. For small expansions, the common approximation is ΔV/V₀ ≈ 3αΔT.
Worked Example
Using the defaults—length 0.2 m, diameter 0.05 m, α = 0.000023 1/K, and a temperature rise of 100 K—the scale factor is:
1 + αΔT = 1 + (0.000023 × 100) = 1.0023.
The expanded length is 0.2 × 1.0023 = 0.200460 m. The expanded diameter is 0.05 × 1.0023 = 0.050115 m, and the expanded radius is (0.05/2) × 1.0023 = 0.025058 m.
The initial volume is π × (0.05/2)² × 0.2 = 0.00039269908 m³. Therefore, the expanded volume is 0.00039269908 × 1.0023³ = 0.000395417 m³ (to the calculator’s displayed precision).
Assumptions
- The cylinder expands freely, with no clamp, press fit, surrounding structure, or applied load preventing movement.
- The material is homogeneous and isotropic, so it expands equally in every direction.
- The coefficient α stays constant across the temperature interval. The result is an estimate when α varies significantly with temperature.
- The temperature is uniform throughout the cylinder, and the input is a temperature change, not an absolute temperature.
- The cylinder remains in the same shape and phase; the calculation does not account for melting, cracking, plastic deformation, or other changes.
How to Choose the Expansion Coefficient
The coefficient depends on the material and can also depend on its composition, treatment, temperature, and direction. Use a value from a reliable material reference that matches the actual material and temperature range as closely as possible. The default, 0.000023 1/K, is a representative approximate value for aluminium; it is not universal for every aluminium alloy or condition.
For anisotropic materials, such as some composites or crystals, expansion can differ by direction. A single coefficient cannot describe all three cylinder dimensions in that case. Use the appropriate directional coefficients and calculate each dimension separately; the volume factor becomes the product of the three directional scale factors rather than necessarily (1 + αΔT)³.
Free Expansion Versus a Constrained Cylinder
The equations above calculate what happens when the cylinder is free to change size. A cylinder held between rigid supports cannot simply attain the calculated length. Instead, restraint creates thermal stress, and the actual deformation depends on the supports, geometry, elastic properties, contact conditions, and loading. A simple free-expansion calculation does not determine that stress or the resulting constrained displacement.
This distinction matters in shafts, bearings, pipework, machine parts, and assemblies with tight clearances. A small diameter change can affect a fit even when the length change seems negligible. For example, if a cylindrical part sits inside a sleeve, calculate the expansion of both parts using their respective materials and temperatures; comparing only the part’s expansion can give the wrong clearance direction or amount.
Common Mistakes and Limits
- Using the wrong temperature input: calculate ΔT = final temperature − initial temperature. Heating gives a positive value; cooling gives a negative value. Do not enter an absolute temperature such as 300 K when the change is 100 K.
- Mixing units: α in 1/K must pair with ΔT in K or °C difference. Keep dimensions in a consistent length unit; this calculator uses metres and returns cubic metres for volume.
- Confusing diameter and radius: the cylinder volume formula uses radius squared. Convert diameter to radius by dividing by 2.
- Assuming volume changes by exactly αΔT: α is the linear coefficient. For isotropic expansion, the small-change volume approximation uses about 3αΔT. The calculator instead applies the cubic scale factor.
- Expecting exact material data: coefficients are often reported as averages over a stated range. Thermal gradients, phase changes, porosity, and mechanical restraint are outside this simple model.
For a modest temperature change, the approximation ΔV ≈ 3αV₀ΔT is often convenient. When high precision matters or the temperature span is wide, use temperature-dependent expansion data and integrate the coefficient over the range rather than treating α as constant. If α is defined as a differential coefficient, the length relation is L = L₀ exp(∫α(T)dT); the constant-α equation is the corresponding practical constant-coefficient model.
Frequently Asked Questions
What is the thermal expansion equation for a cylinder?
For each linear dimension, use L = L₀(1 + αΔT). For an isotropic cylinder’s volume, use V = V₀(1 + αΔT)³, assuming constant α and free, uniform expansion.
Does a cylinder expand in diameter as well as length?
Yes. A freely expanding, isotropic cylinder’s diameter, radius, and length all change by the same fractional amount, αΔT.
Should I use Celsius or kelvins?
Either is valid for a temperature difference: a change of 1 °C equals a change of 1 K. Use a coefficient expressed per degree or per kelvin consistently.
How do I calculate the change in cylinder volume?
Find the original volume V₀ = πr₀²L₀, then calculate V = V₀(1 + αΔT)³. For small changes, ΔV/V₀ is approximately 3αΔT.
What happens if the cylinder is constrained?
It cannot undergo the free dimensional change calculated here without consequence. Restraint may produce stress, so a mechanical analysis using the support and material properties is needed.
Can this equation be used for any material?
Only with an appropriate expansion coefficient and suitable assumptions. Anisotropic materials need direction-specific coefficients, while phase changes or strongly temperature-dependent properties require a more detailed model.
Related
Formula used
in l | Original cylinder length | m | 0.2 | 0 in d | Original cylinder diameter | m | 0.05 | 0 in a | Linear expansion coefficient | 1/K | 0.000023 | 0 in t | Temperature change | K | 100 | - out ln | Expanded cylinder length | m | l * (1 + a * t) | 6 out dn | Expanded cylinder diameter | m | d * (1 + a * t) | 6 out r | Expanded cylinder radius | m | (d / 2) * (1 + a * t) | 6 out v | Expanded cylinder volume | m^3 | pi * (d / 2)^2 * l * (1 + a * t)^3 | 9
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Gas Correction Factor Formula and Calculator0.9829
- Gas Correction Factor Calculator and Table1.2534
- Gas Temperature: Calculate It from Pressure and Volume298.15 K
- Gas Correction Factor Calculator: Formula and Uses107.322 same as input
- Gas Cv Calculator: Heat Capacity Ratio and Formula20.786 J/(mol·K)
- Density Temperature Correction Calculator and Formula999.25 kg/m^3