“TX 400” alone does not identify a rotor radius: it is not a unique, standard rotor model designation, and rotor radius depends on the specific centrifuge rotor. Use this calculator to convert a measured radius between millimetres, centimetres and metres; enter the distance from the rotor’s axis of rotation to the sample location to get the radius in millimetres.
Formula
The primary result is the measured radius expressed in millimetres:
Rmm = r
- r is the entered radius, measured from the rotor’s rotational axis to the sample position, in millimetres.
- Rmm is that same radius in millimetres.
- Centimetres are calculated as Rcm = r / 10, because 10 mm = 1 cm.
- Metres are calculated as Rm = r / 1000, because 1000 mm = 1 m.
The calculator is a unit converter, not a lookup for an undocumented TX 400 rotor. Its default radius of 100 mm is a convenient example value, not a claimed measurement or specification for any TX 400 product.
Worked Example
Using the default input, r = 100 mm:
- Radius in millimetres: Rmm = 100 mm = 100.0 mm.
- Convert millimetres to centimetres: Rcm = 100 / 10 = 10.00 cm.
- Convert millimetres to metres: Rm = 100 / 1000 = 0.100 m.
The radius result is therefore 100.0 mm. The example does not mean that a TX 400 rotor has this radius; the actual value must come from the exact rotor’s documentation or a suitable measurement.
Assumptions
- The input is a radial distance from the axis of rotation, not the rotor’s diameter, circumference, or distance from the outer edge of its housing.
- The input is already measured in millimetres; the converter does not infer a value from a rotor name.
- The sample position must be specified when a rotor’s geometry or tube angle means that different points have different radii.
What “TX 400” Tells You
A model name or short label is not enough to establish a centrifuge rotor’s radius. Similar or reused designations can refer to different equipment, and a number in a name may describe a product series, a capacity, or something else entirely. It should not be treated as a radius or as a reliable substitute for a manufacturer’s rotor specification.
To identify the correct value, check the nameplate and documentation for the centrifuge and the removable rotor itself. Record the complete rotor model or part number, not just “TX 400.” If the label is worn or ambiguous, the equipment documentation or the responsible laboratory staff can help identify the correct manual. Do not assume that a rotor described as compatible has the same geometry as another rotor.
How to Measure the Radius
Rotor radius is the distance from the axis of rotation to a point of interest. For centrifugal calculations, the relevant point is usually the sample’s location in its tube or container. Depending on the rotor and the convention used by the instrument documentation, that can mean the bottom of the sample, the top of the sample, or a specified average position. Those choices can produce different values, so follow the convention required by the calculation or rotor documentation.
- Identify the centreline or axis about which the rotor turns.
- Identify the specific sample position required, such as the tube bottom or sample midpoint.
- Measure the straight-line radial distance between that axis and that position, in millimetres.
- Check whether the documented value is a maximum, minimum, or average radius before using it.
A tube held at an angle does not make the radius the tube’s length. The radius is still the distance outward from the rotation axis to the specified sample point. For a swinging-bucket rotor, the bucket’s position during operation can differ from its resting position; use the operating geometry or the specified radius in the rotor documentation rather than measuring the rotor while it is at rest.
Radius, Diameter, and Centrifugal Force
Radius and diameter are easily confused. The diameter spans the full circle through the axis; the radius runs from the axis to one side. If all you know is the diameter, the radius is half of it: r = diameter / 2. For example, a 200 mm diameter corresponds to a 100 mm radius, but only if that diameter actually spans the relevant rotational path.
Radius is also used to calculate relative centrifugal force (RCF), often reported as multiples of gravity. With rotational speed in revolutions per minute and radius in centimetres, a commonly used relationship is:
RCF = 1.118 × 10−5 × rcm × RPM2
This relationship explains why using the wrong radius matters: RCF changes directly with radius and with the square of rotational speed. A radius error of 10% gives a 10% error in calculated RCF when speed is unchanged. This page’s calculator only converts radius units; it does not calculate RCF, verify rotor speed limits, or establish safe operating conditions.
Common Errors and Safe Use
- Using a product label as a dimension: Do not infer radius from “TX 400” unless the official documentation explicitly defines it as a radius.
- Entering diameter as radius: If the measured value is a diameter, divide by two before entering it.
- Mixing units: RCF formulas commonly require centimetres, while other calculations may ask for metres or millimetres. Convert deliberately.
- Choosing the wrong sample point: The bottom, midpoint, and top of a sample can lie at different radii.
- Measuring a resting swinging bucket: Its operating position may change, so consult the rotor’s specified geometry.
Rotor identification, speed limits, loading, inspection, and balancing are separate safety matters. Use the exact rotor’s operating instructions and the centrifuge’s approved limits; never use a guessed radius to justify exceeding them. If a rotor is damaged, corroded, or cannot be positively identified, do not operate it until it has been assessed under the applicable laboratory procedures.
Frequently Asked Questions
What is the TX 400 rotor radius?
There is no single verifiable radius established by the name “TX 400” alone. The exact rotor model and the specified sample position are needed to obtain the correct value.
Is TX 400 a rotor model?
The label by itself is not enough to identify a unique rotor specification. Check the full equipment and rotor identification, including any model number or part number, against the corresponding documentation.
How do I find a centrifuge rotor radius?
Look in the rotor’s manual or technical specification for its radius and the position that value refers to. If you measure it, take the radial distance from the rotational axis to the sample position required by your calculation.
Is rotor radius half the rotor diameter?
Yes, when the diameter is measured across the circular path through the axis. A housing dimension or a tube length may not be that diameter, so confirm what was measured.
Why does rotor radius matter?
Radius is part of the relationship between rotational speed and centrifugal force. In common RCF calculations, force is proportional to radius and to the square of RPM, so an incorrect radius changes the result.
Related
Formula used
in r | Measured rotor radius | mm | 100 | 0 out rmm | Rotor radius | mm | r | 1 out rcm | Rotor radius | cm | r / 10 | 2 out rm | Rotor radius | m | r / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp