molecalculator

Moles & Molar Mass

Dry Matter Analysis Calculator: Feed & Forage Basis

Calculator No. 01-9959 · Updated · Formula and assumptions shown below

Nutrient on dry matter basis 13.56 %
Nutrient on as-fed basis
12.00 %
= Nutrient on dry matter basis × (Dry matter of feed ÷ 100)
Dry matter of feed
88.5 %
Set in the form below
Nutrient value (as-fed)
12 %
Set in the form below
You enter
Dry matter of feed (%), Nutrient value (as-fed) (%)
You get
Nutrient on dry matter basis (%), Nutrient on as-fed basis (%)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a feed or forage analysis between “as-fed” (as-is) and “dry matter” (DM) bases. You enter the moisture or dry matter percentage and the value you want to convert (e.g., protein, fiber, fat), and it returns the same nutrient expressed on a dry matter basis, which is the standard for comparing feeds, formulating rations, and evaluating forage quality.

Formula

The core relationship is a simple proportion. A nutrient percentage on an as-fed basis is the amount of that nutrient per 100 units of the feed as it is weighed. To express it on a dry matter basis, you divide by the dry matter fraction:

Nutrient (DM basis) = Nutrient (as-fed) ÷ (Dry matter % ÷ 100)

Where:

  • Nutrient (as-fed) is the percentage reported by the lab on the feed as you receive it (includes moisture).
  • Dry matter % is the percentage of the feed that is not water (100 – moisture %).
  • Nutrient (DM basis) is the percentage of the nutrient in the dry portion only.

To go the other way (from DM basis to as-fed), multiply by the dry matter fraction: Nutrient (as-fed) = Nutrient (DM basis) × (Dry matter % ÷ 100).

Worked Example

Using the default values: a hay analysis reports 12.0% crude protein on an as-fed basis, and the hay has 88.5% dry matter (meaning 11.5% moisture).

Step 1: Convert the dry matter percentage to a fraction: 88.5 ÷ 100 = 0.885.

Step 2: Divide the as-fed protein by the fraction: 12.0 ÷ 0.885 = 13.5593…

Step 3: Round to two decimal places: 13.56% crude protein on a dry matter basis.

The calculator’s first output shows 13.56, matching this result. The second output (as-fed basis) demonstrates the reverse calculation: 13.56 × 0.885 = 12.00%, which confirms the original value.

Assumptions

  • Moisture and dry matter percentages are measured by the lab using standard oven-drying or NIR methods.
  • The nutrient percentage (protein, fiber, fat, ash) is reported on the same sample as the moisture value.
  • All percentages are on a weight/weight basis (grams per 100 grams).
  • The dry matter basis is a mathematical re-expression; it does not change the actual amount of nutrient in the feed.

Why Use Dry Matter Basis?

Feeds vary enormously in water content. Fresh grass might be 20% dry matter, while a pelleted concentrate might be 90%. If you compare crude protein as-fed, the fresh grass looks far lower in protein than it really is, simply because it contains so much water. Converting both to a dry matter basis removes moisture as a variable, letting you compare the actual nutrient density of different feeds.

This matters for ration formulation. When a nutritionist says a dairy cow needs a ration with 17% crude protein on a dry matter basis, they mean the dry ingredients combined should hit that figure. If you only have as-fed values, you cannot mix feeds correctly because each feed contributes a different amount of water.

It also matters for purchasing. Hay sold by the bale or ton is priced on an as-fed weight, but its nutritional value is in the dry matter. Two hays with the same price per ton can have very different costs per pound of dry matter if one has 10% moisture and the other 15%. Converting to DM basis lets you calculate the true cost per unit of nutrient.

Common Mistakes and How to Avoid Them

  • Confusing moisture with dry matter. If the lab reports 11.5% moisture, the dry matter is 88.5%, not 11.5%. Always check which one you have.
  • Using the wrong direction. To convert as-fed to DM, you divide by the DM fraction. To convert DM to as-fed, you multiply. Dividing when you should multiply will give a number that is too high or too low by a factor related to the moisture content.
  • Rounding too early. Rounding the DM fraction to 0.89 instead of 0.885 changes the result slightly. Keep at least three significant figures in intermediate steps.
  • Mixing units. This calculator works with percentages. If your nutrient value is in grams per kilogram (g/kg), divide by 10 to get a percentage before entering it, or multiply the result by 10 afterward.
  • Forgetting that DM basis is always higher. Since dry matter is less than 100% of the as-fed weight, the nutrient percentage on a DM basis will always be numerically larger than the as-fed value. If your converted number is lower, you likely divided incorrectly.

When to Use This Calculator

Use this tool whenever you have a lab report with both a moisture (or dry matter) value and a nutrient value, and you need to compare that nutrient across feeds with different water contents. Common situations include:

  • Comparing protein or energy content of hay, silage, and fresh pasture.
  • Formulating a total mixed ration (TMR) where ingredients have different moisture levels.
  • Calculating the dry matter intake of an animal when you only know as-fed intake.
  • Evaluating whether a feed additive or supplement is cost-effective on a dry matter basis.
  • Adjusting a feed tag’s guaranteed analysis to a common basis for comparison shopping.

Note that this calculator handles a single nutrient at a time. For a full ration evaluation, you would repeat the conversion for each nutrient (protein, fiber, fat, minerals) and then combine the dry matter weights of each ingredient.

Limitations and Context

The dry matter conversion is mathematically straightforward, but the underlying analysis has limits. Dry matter measured by oven drying can underestimate true dry matter for feeds with volatile compounds (like silage), where some organic acids and alcohols evaporate with the water. For those feeds, labs may use a correction factor or a toluene distillation method. The calculator assumes the reported dry matter is accurate.

Also, dry matter basis does not account for digestibility. Two hays with the same 14% protein on a DM basis may differ in how much of that protein the animal can actually use, depending on fiber content and heat damage during storage. The conversion is a standardization step, not a quality score.

Finally, remember that dry matter percentage itself changes with storage. Hay left uncovered can absorb moisture, lowering its DM percentage and changing the as-fed nutrient values even though the nutrient content on a DM basis stays the same. Always use a recent analysis for the specific lot of feed you are feeding.

Frequently Asked Questions

What is the difference between as-fed and dry matter basis?
As-fed basis includes the water in the feed; dry matter basis excludes it. For example, a feed with 10% moisture and 8% protein as-fed has 8 ÷ 0.90 = 8.89% protein on a dry matter basis. The dry matter basis is always higher because you are dividing by a number less than 1.

How do I convert dry matter back to as-fed?
Multiply the dry matter basis value by the dry matter fraction. If a feed has 90% dry matter and 15% protein on a DM basis, the as-fed protein is 15 × 0.90 = 13.5%. This is useful when you need to know how much of a feed to weigh out for a ration.

Why does my feed tag show different numbers than the lab analysis?
Feed tags often report guaranteed minimums or maximums on an as-fed basis, while labs may report actual values on a dry matter basis. Also, the tag reflects the product at the time of manufacturing, but moisture can change during storage. Always convert to a common basis before comparing.

Can I use this calculator for pet food or human food?
Yes, the same math applies to any food or feed. Pet food labels sometimes list guarantees on an as-fed basis, and converting to dry matter helps compare canned versus dry diets. For human food, the same conversion works for comparing nutrient density per 100 grams, though labels are typically already on an as-fed basis.

What if my lab report gives moisture instead of dry matter?
Subtract the moisture percentage from 100 to get dry matter. For example, 11.5% moisture means 88.5% dry matter. Enter that number into the calculator. If you enter moisture by mistake, your converted nutrient values will be far too high.

Does dry matter basis change the amount of feed I should give?
No, the actual nutrient amount in the feed does not change. The conversion only changes how you express the percentage. However, when formulating a ration, you should work in dry matter weights, then convert the total to as-fed weights to know how much to physically weigh out for each animal.

Related

Formula used
in dm | Dry matter of feed | % | 88.5 | 0 | 100
in val | Nutrient value (as-fed) | % | 12.0 | 0 | 100
out dmval | Nutrient on dry matter basis | % | val / (dm / 100) | 2
out asfed | Nutrient on as-fed basis | % | dmval * (dm / 100) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →