molecalculator

Moles & Molar Mass

US Customary Units for Pressure: PSI, inHg, and More

Calculator No. 01-11957 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The US customary units for pressure are the pound per square inch (psi), inches of mercury (inHg), and, for atmospheric pressure, the atmosphere (atm) and the bar are also used. The most common everyday unit is psi, which measures force in pounds applied over an area in square inches.

Formula

The calculator converts between psi, inHg, atm, kPa, bar, and mmHg using these exact conversion factors:

  • 1 psi = 6.894757 kPa
  • 1 inHg = 3.386389 kPa
  • 1 atm = 101.325 kPa
  • 1 bar = 100 kPa
  • 1 mmHg = 0.133322 kPa (same as 1 torr)

In the calculator, you enter a pressure in any of the three US customary units (psi, inHg, atm) and it sums their contributions in kPa, then converts to bar and mmHg. The formula is: kPa = (psi × 6.894757) + (inHg × 3.386389) + (atm × 101.325).

Worked Example

Suppose you have a tire pressure of 32 psi, a barometric reading of 29.92 inHg (standard sea-level pressure), and 1 atm (standard atmospheric pressure). Using the defaults from the calculator:

  1. Convert psi to kPa: 32 × 6.894757 = 220.632 kPa
  2. Convert inHg to kPa: 29.92 × 3.386389 = 101.325 kPa
  3. Convert atm to kPa: 1 × 101.325 = 101.325 kPa
  4. Sum: 220.632 + 101.325 + 101.325 = 423.282 kPa
  5. Convert to bar: 423.282 / 100 = 4.233 bar
  6. Convert to mmHg: 423.282 × 7.50062 = 3174.7 mmHg

The calculator shows 423.28 kPa, 4.233 bar, and 3174.7 mmHg.

Assumptions

  • All conversions use the standard international definitions of these units.
  • The calculator assumes you are entering gauge pressure (relative to atmospheric) or absolute pressure as given; it does not add or subtract atmospheric pressure automatically.
  • Inches of mercury (inHg) refers to the height of a mercury column at 0 °C under standard gravity.

Background: Why the US Uses These Units

The US customary system evolved from English units that were in use before the metric system was standardized. Pressure measurements in the US are a mix of units that came from different practical contexts:

  • psi came from steam engine technology in the 19th century, where pressure was measured as pounds of force on a square inch of boiler surface.
  • inHg came from mercury barometers, which were the standard way to measure atmospheric pressure in weather forecasting.
  • atm was defined as the average sea-level atmospheric pressure, originally based on the height of a mercury column (760 mmHg).

While most of the world uses the pascal (Pa) or kilopascal (kPa), the US continues to use psi for tires, scuba tanks, and hydraulic systems. InHg remains in weather reports and aviation altimeter settings.

How to Read and Convert These Units

When you see a pressure value in psi, it tells you how many pounds of force are exerted on each square inch of surface. For example, a car tire at 32 psi means the air inside pushes outward with 32 pounds of force on every square inch of the tire’s inner surface.

Inches of mercury is a bit different: it’s the height of a column of mercury that the atmospheric pressure can support. At sea level, that’s about 29.92 inches. Weather maps often show barometric pressure in inHg, with readings around 30.00 inHg considered normal.

To convert between these units, you can use the factors above or the calculator. A quick mental reference: 1 atm ≈ 14.7 psi ≈ 29.92 inHg ≈ 101.325 kPa.

Common Problems and Misconceptions

One frequent mistake is mixing gauge pressure with absolute pressure. Gauge pressure (psig) is measured relative to atmospheric pressure, so a tire at 32 psig is actually 32 + 14.7 = 46.7 psia (absolute). Most everyday measurements are gauge, but engineering calculations often need absolute.

Another confusion is between inHg and mmHg. Both are mercury-column heights, but they differ by a factor of 25.4 (since 1 inch = 25.4 mm). So 29.92 inHg equals 760 mmHg, which is the standard atmospheric pressure.

Some people think psi and bar are the same, but 1 bar is about 14.5 psi. This causes errors when reading European equipment that specifies pressure in bar.

How to Choose the Right Unit

Which unit you should use depends on your field:

  • Automotive and tires: psi is standard in the US.
  • Weather and aviation: inHg is used in the US for barometric pressure and altimeter settings.
  • Scuba diving: psi for tank pressure, but also bar in many countries.
  • Science and engineering: kPa, bar, or atm are common, with pascal being the SI unit.
  • HVAC and refrigeration: psi is typical for refrigerant pressures.

If you’re working with international colleagues or scientific literature, it’s safest to convert to kPa or bar. The calculator above helps you do that quickly.

Safety and Accuracy Notes

When measuring pressure in real systems, always use a calibrated gauge and follow the manufacturer’s specifications. Over-pressurizing tires, tanks, or pipes can cause dangerous failures. For laboratory work, follow your lab method, the safety data sheet (SDS) and your supervisor. Also, remember that pressure measurements are temperature-dependent for gases; a tire at 32 psi on a cold morning will read higher after driving because the air warms up.

Frequently Asked Questions

What does psi stand for?

Psi stands for pounds per square inch. It measures the force (in pounds) exerted on one square inch of area. It’s the most common pressure unit in the US for everyday applications like tire pressure and air compressors.

How do I convert psi to kPa?

Multiply the psi value by 6.894757. For example, 30 psi × 6.894757 = 206.84 kPa. Conversely, divide kPa by 6.894757 to get psi.

Why is atmospheric pressure often given as 29.92 inHg?

That’s the standard sea-level atmospheric pressure expressed as the height of a mercury column. It equals 760 mmHg, 101.325 kPa, or 14.7 psi. Weather reports use inHg because barometers originally measured the height of mercury.

Is bar the same as atm?

No, they are close but not equal. 1 atm = 1.01325 bar, and 1 bar = 0.9869 atm. The difference is about 1.3%. Many engineering applications use bar because it’s a round number in the metric system.

What is the difference between gauge and absolute pressure?

Gauge pressure (psig) is measured relative to atmospheric pressure, so it reads zero at sea level. Absolute pressure (psia) includes atmospheric pressure. To convert: absolute = gauge + 14.7 psi (at sea level). For example, a tire at 32 psig is at 46.7 psia.

Do US customary pressure units have any official definition?

Yes. The US National Institute of Standards and Technology (NIST) defines these units in terms of SI units. For instance, 1 psi is exactly 6.894757 kPa, and 1 inHg is exactly 3.386389 kPa at 0 °C. These are internationally recognized conversion factors.

Related

Formula used
in psi | Pressure in psi | psi | 14.7 | 0
in inHg | Pressure in inHg | inHg | 29.92 | 0
in atm | Pressure in atm | atm | 1 | 0
out kpa | Pressure in kilopascals | kPa | psi * 6.894757 + inHg * 3.386389 + atm * 101.325 | 2
out bar | Pressure in bar | bar | kpa / 100 | 3
out mmhg | Pressure in mmHg | mmHg | kpa * 7.50062 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →