molecalculator

Moles & Molar Mass

Vacuum Pressure Conversion Calculator

Calculator No. 01-11958 · Updated · Formula and assumptions shown below

Pressure in torr 1.00 torr
Pressure in millibar
1.33 mbar
= Pressure in torr × 1.333223684
Pressure in pascal
133.3 Pa
= Pressure in torr × 133.322368
Pressure in inches of mercury
0.03937 inHg
= Pressure in torr ÷ 25.4000
You enter
Pressure value (torr), Input unit
You get
Pressure in torr (torr), Pressure in millibar (mbar), Pressure in pascal (Pa), Pressure in inches of mercury (inHg)
Rounding
2 dp · 1 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts between common vacuum pressure units: torr, millibar, pascal, and inches of mercury (inHg). You enter a pressure value in any of these units, and it instantly returns the equivalent in all the others, so you can compare readings from different gauges or specifications.

Formula

The conversion relies on the definition of the torr: 1 torr = 1/760 standard atmosphere = 133.322368 pascals exactly. From that base, the other units are derived:

  • 1 torr = 133.322368 Pa
  • 1 mbar = 100 Pa, so 1 torr = 1.333223684 mbar
  • 1 inHg = 3386.389 Pa (at 0 °C), so 1 torr = 133.322368 / 3386.389 ≈ 0.0393701 inHg

In the calculator, the input unit selector multiplies your entered value by a factor that converts it to torr first, then the outputs convert torr to each target unit. For example, if you enter 1 with unit “mbar”, the factor 1.333223684 converts it to 1.3332 torr, and the outputs show that value in all units.

Worked Example

Using the default value of 1 torr with unit “torr”:

  1. Convert to torr: 1 × 1 = 1 torr
  2. To millibar: 1 × 1.333223684 = 1.3332 mbar (rounded to 2 decimals)
  3. To pascal: 1 × 133.322368 = 133.3 Pa (rounded to 1 decimal)
  4. To inches of mercury: 1 / 25.4000 = 0.03937 inHg (rounded to 3 decimals)

So 1 torr equals 1.3332 mbar, 133.3 Pa, and 0.03937 inHg. These are the exact results the calculator returns.

Assumptions

  • The torr is defined as exactly 1/760 of a standard atmosphere.
  • Inches of mercury are referenced to 0 °C (density of mercury = 13.5951 g/cm³).
  • All conversions assume the same physical pressure; temperature effects on the mercury column are ignored.
  • Pressure values are non-negative; the calculator rejects negative inputs.

When to Use This Calculator

Vacuum pressure is measured in many units depending on the field and the gauge. A chemist reading a rotary evaporator might see millibar; a vacuum oven may display torr or mbar; a refrigeration technician uses inches of mercury; a physicist may use pascals. This calculator helps you:

  • Compare a gauge reading to a specification written in a different unit.
  • Convert between absolute and gauge pressure readings (if you know the atmospheric baseline).
  • Check whether a vacuum pump reaches the required pressure for a process, such as a freeze dryer or a Schlenk line.

For example, if your vacuum pump spec says “ultimate vacuum 0.1 mbar,” you can enter 0.1 mbar and see it equals 0.075 torr or 10 Pa. That tells you the pump can reach about 10 Pa, which is a typical rough vacuum.

How to Read the Results

The first output, “Pressure in torr,” is the headline answer. The other outputs give the same pressure in the other three units. When you change the input unit, the calculator first normalizes to torr, then converts to all outputs. Always note which unit you are entering; the drop-down selector is part of the input.

One common mistake is confusing absolute pressure with gauge pressure. Vacuum gauges often read “negative” relative to atmosphere (e.g., -30 inHg gauge), but the calculator expects absolute pressure. To convert a gauge reading to absolute, subtract it from the local atmospheric pressure. For example, if your gauge reads -25 inHg and atmospheric pressure is 29.92 inHg, the absolute pressure is 4.92 inHg. Enter 4.92 inHg to get the equivalent in torr or mbar.

Common Mistakes and Misconceptions

  • Mixing torr and mmHg: They are numerically identical (1 torr = 1 mmHg at 0 °C), but some sources round differently. Our calculator treats them as equal.
  • Using the wrong conversion factor for inHg: The factor depends on temperature because mercury density changes. We use the standard 0 °C value; at room temperature the difference is less than 0.1% for most purposes.
  • Forgetting to convert gauge to absolute: Many vacuum readings are gauge pressures. The calculator only works with absolute pressures, so you must adjust first.
  • Assuming mbar and hPa are different: They are exactly the same (1 mbar = 1 hPa). The calculator uses mbar, but you can use it for hPa as well.

Practical Context: Vacuum Levels

Here are typical vacuum ranges to help you interpret results:

  • Rough vacuum: 1 to 1000 mbar (0.75 to 750 torr) – used for filtration, rotary evaporation.
  • Medium vacuum: 10⁻³ to 1 mbar (0.75 to 750 mtorr) – used for freeze drying, vacuum ovens.
  • High vacuum: 10⁻⁶ to 10⁻³ mbar – used in electron microscopes and surface science.
  • Ultra-high vacuum: below 10⁻⁶ mbar – used in particle accelerators.

Knowing these levels helps you decide if a pump is adequate. For example, a typical two-stage rotary vane pump reaches about 0.001 mbar, which is 0.00075 torr or 0.75 mtorr – enough for most lab work.

Safety and Lab Practice

When working with vacuum systems, always follow your lab’s standard operating procedures and the safety data sheet (SDS) for any materials involved. Vacuum glassware can implode if damaged; use proper shielding and inspect glass for cracks. Never evacuate a vessel beyond its rated pressure, and always use a trap to protect the pump from solvent vapors. This calculator is for study and planning arithmetic only; always verify actual pressures with a calibrated gauge.

Frequently Asked Questions

What is the difference between torr and mmHg?

At 0 °C, 1 torr is exactly equal to 1 mmHg because both are defined as 1/760 of a standard atmosphere. The name “torr” honors Evangelista Torricelli, and “mmHg” refers to the height of a mercury column. In practice they are interchangeable; the calculator treats them as the same.

How do I convert inHg to mbar?

First convert inHg to torr by dividing by 0.0393701 (or multiplying by 25.4), then multiply by 1.333223684 to get mbar. For example, 1 inHg = 25.4 torr = 33.86 mbar. The calculator does this automatically.

Why does my vacuum gauge show negative numbers?

Most mechanical vacuum gauges measure gauge pressure relative to atmospheric pressure. A reading of -25 inHg means the absolute pressure is 25 inHg below atmospheric. To get absolute pressure, subtract the gauge reading from the atmospheric pressure (typically 29.92 inHg at sea level). This calculator requires absolute pressure, so adjust accordingly.

What is a good vacuum for rotary evaporation?

Typically 10 to 100 mbar (7.5 to 75 torr) is used, depending on the solvent and temperature. Water boils at about 20 °C at 23 mbar, for example. Use the calculator to check if your pump can achieve the required pressure.

Can I use this calculator for high vacuum work?

Yes, the conversion is linear and works for any positive pressure, including very low values. However, at pressures below 10⁻⁶ mbar, other units like pascal are more common, and the calculator handles that conversion fine.

Related

Formula used
in p | Pressure value | torr | 1 | 0
sel u | Input unit | torr=1, mbar=1.333223684, Pa=0.00750061683, inHg=25.4000
out torr | Pressure in torr | torr | p * u | 2
out mbar | Pressure in millibar | mbar | torr * 1.333223684 | 2
out pa | Pressure in pascal | Pa | torr * 133.322368 | 1
out inhg | Pressure in inches of mercury | inHg | torr / 25.4000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →