molecalculator

Moles & Molar Mass

Water Density at Pressure: Calculate It

Calculator No. 01-2160 · Updated · Formula and assumptions shown below

Water density 998 kg/m^3
Specific volume
0.001002 m^3/kg
= 1 ÷ Water density
Temperature
20 °C
Set in the form below
Absolute pressure
0.101325 MPa
Set in the form below
You enter
Temperature (°C), Absolute pressure (MPa)
You get
Water density (kg/m^3), Specific volume (m^3/kg)
Rounding
0 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates the density of liquid water from its temperature and pressure, using a standard empirical equation of state. Enter temperature in °C and absolute pressure in MPa; the result is density in kg/m³, along with specific volume in m³/kg. The model is intended for ordinary liquid-water conditions, not ice or steam.

Formula

For the estimate, the calculator uses a fifth-degree fit for water density at atmospheric pressure, then applies a small pressure correction:

ρ(T, p) = ρ₀(T) × [1 + (p − 0.101325 MPa) / 2200 MPa]

ρ₀(T) is calculated as 999.842594 + 0.06793952T − 0.00909529T² + 0.0001001685T³ − 0.000001120083T⁴ + 0.000000006536332T⁵, in kg/m³. Here, T is temperature in °C, p is absolute pressure in MPa, and ρ is the estimated liquid-water density in kg/m³. The value 2200 MPa is an approximate bulk modulus used to represent water’s resistance to compression; it is a simplifying constant, not an exact value at every temperature and pressure. Specific volume is v = 1/ρ, in m³/kg.

The atmospheric reference pressure is 0.101325 MPa, equivalent to 101.325 kPa. The model’s temperature polynomial is a commonly used fit to atmospheric-pressure water density over 0–100 °C. The linear pressure factor is useful for a modest correction, but does not replace a full water-property formulation for high-accuracy work.

Worked Example

Using the defaults, T = 20 °C and p = 0.101325 MPa. First evaluate the atmospheric-pressure polynomial:

ρ₀(20) = 999.842594 + 0.06793952(20) − 0.00909529(20²) + 0.0001001685(20³) − 0.000001120083(20⁴) + 0.000000006536332(20⁵)

ρ₀(20) ≈ 998.20632 kg/m³. Since the entered pressure equals the reference pressure, the pressure factor is 1 + (0.101325 − 0.101325) / 2200 = 1. Therefore, ρ ≈ 998.20632 kg/m³, displayed to zero decimal places as 998 kg/m³.

The specific volume is v = 1 / 998.20632 ≈ 0.001001797 m³/kg. The calculator displays this to six decimal places as 0.001002 m³/kg. The extra digits in the intermediate density are retained for this calculation; rounding the density first would slightly alter the specific-volume result.

Assumptions

  • The substance is pure liquid water, and the input temperature is from 0 to 100 °C.
  • Pressure is absolute, not gauge pressure. The reference pressure is 0.101325 MPa.
  • The pressure correction treats compressibility as approximately constant, using 2200 MPa as a representative bulk-modulus value.
  • The estimate is for general reference and study, not precision engineering, metrology, or a certified property calculation.

Why Pressure Changes Water Density

Density is mass divided by volume. Water molecules are close together in liquid water, so applying pressure reduces the volume only slightly compared with compressing a gas. Because the mass stays the same while volume falls, density rises. Around room temperature, increasing pressure by 1 MPa changes the estimated density by roughly 0.045%, using the calculator’s 2200 MPa bulk-modulus approximation.

Pressure needs to be specified as absolute pressure for this calculation. Gauge pressure is measured relative to the surrounding atmosphere. To convert a gauge reading to absolute pressure, add the local atmospheric pressure, then express the result in MPa. For example, 1 MPa gauge is about 1.101 MPa absolute when atmospheric pressure is near 0.101 MPa. Using a gauge value directly would understate the pressure in the formula.

Temperature Matters Too

For water near atmospheric pressure, density reaches its maximum at about 4 °C, at roughly 1000 kg/m³. It is less dense both above and below that temperature. This unusual behavior is why the calculator uses a temperature polynomial rather than assuming density always falls as water warms. At 20 °C, water is about 998.2 kg/m³; at 100 °C and atmospheric pressure, the liquid-water value is about 958.4 kg/m³.

These figures describe liquid water. At a given pressure, water can boil before reaching 100 °C if the pressure is below standard atmospheric pressure, or remain liquid above 100 °C if pressure is higher. The calculator does not locate boiling conditions or calculate steam density. Do not interpret its result as valid for a two-phase mixture containing both liquid and vapor.

When This Estimate Is Useful—and Its Limits

This calculation is suitable for classroom estimates, rough mass–volume conversions, and understanding how pressure affects liquid water. If a known water volume is V in m³, its estimated mass is m = ρV in kg. Conversely, volume is approximately mass divided by density. Use consistent units: 1 L = 0.001 m³, so a density in kg/m³ can be used with litres only after converting the volume.

For precise work, use a recognized water and steam property formulation, such as the International Association for the Properties of Water and Steam (IAPWS) formulation, or reliable tabulated data for the exact temperature and pressure. The simple correction here assumes a fixed compressibility. Real water’s compressibility varies with temperature and pressure, so errors grow as conditions move away from the reference range. The pressure input permits values up to 100 MPa, but that range is a calculator limit, not a guarantee of high accuracy there.

  • Check that pressure is absolute and in MPa; convert kPa to MPa by dividing by 1000.
  • Use the result only for liquid water within the stated temperature range.
  • Keep sufficient precision during intermediate steps; the displayed density is rounded to a whole kg/m³.
  • For high-pressure systems, process design, or safety-critical calculations, use validated property data and the applicable engineering method.

Frequently Asked Questions

What is the density of water at 1 atm?
It depends on temperature. At about 4 °C it is close to 1000 kg/m³; at 20 °C it is about 998.2 kg/m³, and at 100 °C saturated liquid water is about 958.4 kg/m³.

Does water get denser when pressure increases?
Yes, while it remains liquid. Higher pressure compresses water slightly, reducing its volume and increasing its density. The change is modest because liquid water is only weakly compressible.

Is 1 MPa the same as 1 MPa absolute?
Not necessarily. A pressure written as 1 MPa without qualification may mean gauge or absolute pressure. This calculator requires absolute pressure; add local atmospheric pressure to a gauge reading before entering it.

Why is ice less dense than liquid water?
Ordinary ice has an open crystal structure that occupies more volume for the same mass than liquid water. This makes ice less dense, so it floats. The liquid-water calculator does not apply to ice.

Can this calculate water density above 100 °C?
No. Above 100 °C, whether water is liquid depends on pressure, and the formula is not designed for that region. Use validated steam-table or IAPWS data for temperatures and pressures outside the stated range.

Related

Formula used
in t | Temperature | °C | 20 | 0 | 100
in p | Absolute pressure | MPa | 0.101325 | 0 | 100
out rho | Water density | kg/m^3 | (999.842594 + 0.06793952 * t - 0.00909529 * t^2 + 0.0001001685 * t^3 - 0.000001120083 * t^4 + 0.000000006536332 * t^5) * (1 + (p - 0.101325) / 2200) | 0
out v | Specific volume | m^3/kg | 1 / rho | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →