This concentration calculator finds the molarity of a solution from the mass of a solute, its molar mass, and the final solution volume. Enter those values to get concentration in mol/L and millimolar (mM); the result assumes the volume is the volume of the completed solution, not just the solvent.
Formula
For a solution whose solute amount is given by mass, the standard molarity formula is:
c = n / V = (m / M) / (VmL / 1000)
- c is molar concentration, or molarity, in mol/L.
- n is the amount of solute in moles, calculated as m / M.
- m is the solute mass in grams (g).
- M is the solute molar mass in grams per mole (g/mol).
- VmL is the final solution volume in millilitres (mL). Dividing by 1000 converts it to litres (L), because 1000 mL = 1 L.
The equivalent mass form is c = 1000m / (MVmL). Molarity is the number of moles of solute per litre of solution. It is not the number of moles per litre of solvent. To express the same concentration in millimolar, use cmM = 1000c, since 1 mol/L = 1000 mmol/L.
Worked Example
Using the calculator defaults—2.922 g of solute, a molar mass of 58.44 g/mol, and a final solution volume of 250 mL:
- Find the amount in moles: n = m / M = 2.922 g / (58.44 g/mol) = 0.050000 mol.
- Convert the volume: 250 mL / 1000 = 0.25000 L.
- Calculate molarity: c = 0.050000 mol / 0.25000 L = 0.2000 mol/L.
- Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.
The calculator therefore returns 0.2000 mol/L and 200.00 mM.
Assumptions
- The entered mass is the mass of the solute, and the molar mass matches its chemical form and composition.
- The volume entered is the final volume of the solution, expressed in mL.
- The formula reports analytical molarity: it does not adjust for dissociation, chemical reaction, purity, or temperature-dependent volume changes.
- This is arithmetic for study and lab planning. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
What Concentration Means
In chemistry, concentration describes how much of a specified substance is present in a stated amount of mixture or solution. The word alone does not identify one formula, because concentration can be reported using different quantities and units. Molarity is a common choice in solution chemistry, so this calculator uses the mass-to-moles method to find it.
Other valid concentration measures include mass concentration, such as g/L; mass fraction or percentage; and molality, which is moles of solute per kilogram of solvent. These answer different questions. For example, molarity uses the solution’s volume, while molality uses the solvent’s mass. Always check the unit and definition before comparing two reported values.
When to Use Molarity
Use this formula when you know a solute’s mass and molar mass and want its amount in moles per litre of final solution. It is useful for checking classroom problems, interpreting solution labels, and planning ordinary laboratory calculations. If the amount is already given in moles, calculate c = n / V directly, converting the volume to litres first.
The calculator needs a valid molar mass. For a pure compound, that value is calculated from the chemical formula and the standard atomic weights of its constituent atoms. For instance, sodium chloride has a molar mass of about 58.44 g/mol. Hydrates, salts in different forms, and mixtures can have different relevant molar masses, so a value for one chemical form should not be applied automatically to another. If a reagent is not pure, the mass weighed may not equal the mass of the intended solute; account for purity only when its value and the problem’s assumptions are known.
How to Read and Check the Result
A result of 0.2000 mol/L means there are 0.2000 moles of the specified solute per litre of solution under the stated concentration convention. It does not mean 0.2000 moles per litre of water. The millimolar output is the same concentration in a smaller unit: 200 mM is equivalent to 0.200 mol/L, not a different solution strength.
A useful check is to estimate the answer before relying on the displayed digits. In the example, 2.922 g at 58.44 g/mol is 0.05 mol, and 0.05 mol in a quarter of a litre is 0.2 mol/L. The units also reduce correctly: g divided by g/mol gives mol, then mol divided by L gives mol/L. Report only as many significant figures as the input measurements and purpose justify; extra displayed decimal places do not make an imprecise measurement more accurate.
Common Mistakes and Limits
- Using mL as if it were L: convert mL to L by dividing by 1000. Forgetting this makes the result 1000 times too small when using c = n/V.
- Entering solvent volume: the formula requires final solution volume. Adding solute can change the volume, so the solvent amount alone is not a substitute.
- Mixing up mass and molar mass: mass is in grams; molar mass is in g/mol. Their quotient gives moles.
- Using the wrong chemical form: a hydrate or a different salt form has a different molar mass from the anhydrous compound.
- Treating molarity as particle concentration: for substances that dissociate or react, the concentration of a particular ion or species may differ from the analytical concentration calculated from the starting solute.
This calculation does not determine whether a reaction is complete, whether a solute is fully dissolved, or the concentration of each species in a chemical equilibrium. Nor does it compensate for volume changes with temperature. For questions involving equilibria, ionic strength, or a defined chemical species, additional chemical information and an appropriate model are needed.
Frequently Asked Questions
What is the basic formula for concentration?
Molarity is c = n/V: moles of solute divided by litres of solution. If mass and molar mass are given, use c = (m/M)/V.
How do I calculate concentration from mass?
Divide the solute mass in grams by its molar mass in g/mol to get moles, then divide by the final solution volume in litres. Convert mL to L by dividing by 1000.
Is concentration the same as molarity?
No. Molarity is one specific way to express concentration, in mol/L. Concentration can also be expressed as g/L, a percentage, molality, or other measures.
Does molarity use the volume of solvent or solution?
It uses the total final volume of the solution. The volume of solvent before dissolving the solute is not necessarily the final solution volume.
How do you convert mol/L to mM?
Multiply mol/L by 1000. For example, 0.200 mol/L equals 200 mM.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0 in v | Final solution volume | mL | 250 | 0 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- ABG Temperature Correction Calculator and pH Limits7.40
- API Gravity Temperature Correction Calculator34.44 °API
- Units per mL to Percentage Calculator and Formula0.0100 % w/v
- Volume Calculator in mL: Find Liquid Volume200 mL
- Units per mL Calculator: Convert Concentration to Volume100.00 U/mL
- Per Mile Calculator: Running Pace, Speed and Split Times9.68 min/mi