molecalculator

Moles & Molar Mass

Enthalpy Formula: Definition, Calculation & Units

Calculator No. 01-7888 · Updated · Formula and assumptions shown below

Enthalpy change (ΔH) 10,460.00 J
Enthalpy change
10.4600 kJ
= Enthalpy change (ΔH) ÷ 1000
Mass of substance
100 g
Set in the form below
Specific heat capacity
4.184 J/(g·°C)
Set in the form below
You enter
Mass of substance (g), Specific heat capacity (J/(g·°C)), Temperature change (ΔT) (°C)
You get
Enthalpy change (ΔH) (J), Enthalpy change (kJ)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator computes the change in enthalpy (ΔH) for a chemical reaction or physical process using the standard formula ΔH = ΔU + PΔV, or more practically, ΔH = m·c·ΔT for temperature changes. You enter the mass of the substance, its specific heat capacity, and the temperature change, and the calculator returns the enthalpy change in joules or kilojoules. The result tells you whether the process absorbs heat (endothermic, positive ΔH) or releases heat (exothermic, negative ΔH).

Formula

The enthalpy change for a temperature change is given by:

ΔH = m × c × ΔT

Where:

  • ΔH = change in enthalpy (joules, J, or kilojoules, kJ)
  • m = mass of the substance (grams, g)
  • c = specific heat capacity (J/(g·°C)) – the energy needed to raise 1 gram of the substance by 1 °C
  • ΔT = change in temperature (°C or K, since a difference is the same in both scales)

This is the most common form used in calorimetry. For a chemical reaction at constant pressure, the enthalpy change is also written as:

ΔH = ΔU + PΔV

Where ΔU is the change in internal energy, P is pressure, and ΔV is the change in volume. At constant pressure, ΔH equals the heat absorbed or released (qp).

Worked Example

Using the default values from the calculator: 100 g of water (c = 4.184 J/(g·°C)) heated by 25 °C.

  1. Write the formula: ΔH = m × c × ΔT
  2. Plug in the values: ΔH = 100 g × 4.184 J/(g·°C) × 25 °C
  3. Multiply: 100 × 4.184 = 418.4 J/°C
  4. Then: 418.4 × 25 = 10,460 J
  5. Convert to kJ: 10,460 J ÷ 1000 = 10.46 kJ

The calculator shows ΔH = 10,460.00 J and 10.4600 kJ, matching the manual calculation.

Assumptions

  • The specific heat capacity is constant over the temperature range.
  • No phase change occurs (solid to liquid, liquid to gas) – those require latent heat, not this formula.
  • The process occurs at constant pressure (common for most lab work).
  • The substance is pure and the mass is accurately measured.

When to Use This Formula

Use ΔH = m·c·ΔT when you are heating or cooling a substance and want to know how much heat energy is involved. This is typical in calorimetry experiments, designing heating/cooling systems, or calculating the energy needed to raise a sample to a target temperature.

For chemical reactions, you would instead use Hess’s law or standard enthalpies of formation:

ΔHrxn = Σ ΔHf°(products) − Σ ΔHf°(reactants)

That formula requires tabulated standard enthalpy of formation values, which are not entered here. The calculator above handles the temperature-change part, which is often the missing piece.

How to Read the Result

A positive ΔH means the system absorbs heat from the surroundings (endothermic). A negative ΔH means the system releases heat (exothermic). For example, melting ice absorbs heat (positive), while burning methane releases heat (negative).

In the worked example, heating water gives a positive ΔH because you are adding energy. If you cooled the water, ΔT would be negative, and the result would be negative, indicating heat is removed.

Common Mistakes and Misconceptions

  • Mixing up ΔH and ΔU: ΔH is at constant pressure; ΔU is at constant volume. For solids and liquids the difference is tiny, but for gases it can be significant.
  • Using °C vs K: For ΔT, a change of 1 °C equals a change of 1 K, so either unit works. But if you use absolute temperatures in other formulas, always use kelvin.
  • Forgetting phase changes: This formula does not include latent heat. Melting or boiling requires extra energy (enthalpy of fusion/vaporization) that must be added separately.
  • Wrong specific heat capacity: The value depends on the substance and sometimes temperature. For water it is 4.184 J/(g·°C), but for metals it is much lower (e.g., iron ≈ 0.45).

Limits of the Formula

The simple m·c·ΔT formula assumes constant specific heat and no phase change. Over very large temperature ranges, specific heat varies, so the result is an approximation. For accurate work over wide ranges, you would integrate the heat capacity function. Also, the formula gives the heat transferred, not the total enthalpy of a substance (which is defined relative to a reference state).

For reactions, the enthalpy change also depends on pressure and temperature; standard values are quoted at 25 °C and 1 atm. If your conditions differ, you may need corrections.

Frequently Asked Questions

What is the difference between enthalpy and heat?

Heat (q) is energy in transit due to a temperature difference. Enthalpy (H) is a state function that includes internal energy plus the product of pressure and volume. At constant pressure, the change in enthalpy equals the heat exchanged, which is why the terms are often used interchangeably in lab settings.

Why is enthalpy change positive for endothermic reactions?

Endothermic reactions absorb heat from the surroundings, so the system gains energy. By convention, energy gained by the system is positive. Thus ΔH > 0. Exothermic reactions release energy, so ΔH < 0.

Can I use this formula for gases?

Yes, but be careful. For gases, the specific heat at constant pressure (cp) differs from that at constant volume (cv). Use cp when using ΔH = m·c·ΔT at constant pressure. Also, for gases, the PΔV term can be significant, so ΔH and ΔU are not the same.

How do I calculate ΔH for a reaction from formation enthalpies?

Use the formula: ΔHrxn = Σ ΔHf°(products) − Σ ΔHf°(reactants). Look up the standard enthalpy of formation for each compound (usually in kJ/mol), multiply by the stoichiometric coefficients, sum for products and reactants, and subtract. This gives the enthalpy change for the reaction as written.

What is the unit of enthalpy?

Enthalpy itself is usually reported in joules (J) or kilojoules (kJ). Molar enthalpy (per mole) is in J/mol or kJ/mol. Specific enthalpy (per gram) is in J/g. Always check the context to know which one you need.

Related

Formula used
in m | Mass of substance | g | 100 | 0
in c | Specific heat capacity | J/(g·°C) | 4.184 | 0
in dt | Temperature change (ΔT) | °C | 25 | -273.15
out dh | Enthalpy change (ΔH) | J | m * c * dt | 2
out dkj | Enthalpy change | kJ | dh / 1000 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →