molecalculator

Moles & Molar Mass

M1V1 M2V2 Equation: Name & How to Use It

Calculator No. 01-7807 · Updated · Formula and assumptions shown below

Final volume (V2) 40.00 mL
Initial concentration (M1)
1 mol/L
Set in the form below
Initial volume (V1)
10 mL
Set in the form below
Final concentration (M2)
0.25 mol/L
Set in the form below
You enter
Initial concentration (M1) (mol/L), Initial volume (V1) (mL), Final concentration (M2) (mol/L)
You get
Final volume (V2) (mL)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The M1V1 = M2V2 equation is a dilution formula used to calculate how to dilute a stock solution to a desired concentration. You enter the initial concentration (M1), the initial volume (V1), and either the final concentration (M2) or final volume (V2), and the calculator returns the missing value. This page explains the formal name of the equation, its derivation, and how to apply it correctly in lab calculations.

Formula

The equation is written as:

M1 × V1 = M2 × V2

Where:

  • M1 = initial molar concentration of the stock solution (mol/L, often written as M)
  • V1 = volume of the stock solution taken (mL or L)
  • M2 = final molar concentration after dilution (mol/L)
  • V2 = final total volume after dilution (mL or L)

The equation assumes that the amount of solute (in moles) does not change during dilution; only the volume changes. Rearranging for the final volume gives V2 = M1 × V1 / M2, which is what the calculator computes.

Worked Example

Using the default values: M1 = 1.0 mol/L, V1 = 10 mL, M2 = 0.25 mol/L. Calculate V2.

Step 1: Write the equation: M1 × V1 = M2 × V2

Step 2: Substitute the numbers: 1.0 × 10 = 0.25 × V2

Step 3: Solve for V2: V2 = (1.0 × 10) / 0.25 = 10 / 0.25 = 40 mL

The final volume must be 40 mL. This means you would take 10 mL of the 1.0 M stock and add solvent until the total volume reaches 40 mL (not add 30 mL of solvent, but dilute to the 40 mL mark).

Assumptions

  • The solute amount (moles) is conserved during dilution.
  • Volumes are additive (valid for most aqueous solutions at moderate concentrations).
  • The solution is well-mixed and homogeneous.
  • Temperature is constant (molarity changes slightly with temperature because volume changes).

What Is the M1V1 M2V2 Equation Called?

The formal name is the dilution equation or the dilution formula. In chemistry textbooks, it is often referred to as the dilution law or the dilution relation. The symbols M1, V1, M2, V2 are standard notation in analytical chemistry and are used universally in lab protocols and textbooks.

There is no single person who discovered it; it is a direct consequence of the definition of molarity (M = moles/volume). Because the number of moles of solute remains constant when you add solvent, you can set the initial moles equal to the final moles: M1 × V1 = moles = M2 × V2. This is why the equation is sometimes called the moles conservation equation, though that term is less common.

Informally, lab workers might call it the “C1V1 equals C2V2” formula, especially when using concentration units other than molarity (like percent or mg/mL). The letters C (for concentration) and V (for volume) are used interchangeably with M and V. This is not slang; it is a legitimate alternative notation. The equation works for any concentration unit as long as the same unit is used on both sides (e.g., both in mol/L, both in % w/v, both in mg/mL).

How to Use the Equation Correctly

To apply M1V1 = M2V2, you need three of the four values. The most common use is to find the final volume (V2) when you know the stock concentration, the volume you are taking, and the desired final concentration. Here is the step-by-step process:

  1. Identify which values you have and which you need.
  2. Ensure all volumes are in the same unit (both mL or both L). If not, convert.
  3. Ensure all concentrations are in the same unit (both mol/L, both %, etc.).
  4. Plug the numbers into the equation and solve for the unknown.
  5. Interpret the result: if solving for V2, that is the final total volume, not the amount of solvent to add.

For example, to prepare 250 mL of 0.5 M NaCl from a 2 M stock: M1 = 2, V1 = ?, M2 = 0.5, V2 = 250. Rearranging gives V1 = (0.5 × 250) / 2 = 62.5 mL. So you take 62.5 mL of stock and dilute to 250 mL total.

Common Mistakes and Misconceptions

A frequent error is confusing final volume with added solvent. In the example above, you do not add 62.5 mL of solvent; you add enough solvent to reach 250 mL total. If you added 62.5 mL of solvent to 62.5 mL of stock, you would get 125 mL total, which would be twice the intended concentration.

Another mistake is mixing units. If M1 is in mol/L and M2 is in mmol/L, the equation will give a wrong answer. Always convert to the same unit first. For instance, 0.5 M = 500 mM, so if you use mM on one side, use mM on the other.

Some students think the equation only works for molarity. It actually works for any concentration unit that is proportional to moles per volume, including percent concentration, mg/mL, and even ppm (as long as density is constant). However, it does not work for molality (moles per kg of solvent) because molality does not change with volume.

Finally, the equation assumes volumes are additive. For very concentrated solutions or when mixing two different solvents, the final volume may not be exactly the sum of the individual volumes due to contraction or expansion. In such cases, use volumetric glassware to make the final volume precisely.

Why the Equation Works: Derivation from Molarity

Molarity is defined as moles of solute divided by liters of solution: M = n / V, where n is moles and V is volume in liters. Rearranging gives n = M × V. When you dilute a solution, the number of moles of solute does not change; you are only adding more solvent. Therefore, the moles before dilution equal the moles after dilution:

n1 = n2

M1 × V1 = M2 × V2

This derivation shows why the equation is exact for any dilution where no solute is added or removed. It is a conservation of mass statement, not an empirical approximation.

Real-World Applications and Limits

The M1V1 M2V2 equation is used in virtually every chemistry lab. It is essential for preparing buffers, media, reagents, and standard solutions. In biology, it is used to dilute DNA or protein stocks to working concentrations. In analytical chemistry, it is used to prepare calibration standards.

However, the equation has limits. It does not account for changes in density or non-ideal mixing. For extremely accurate work, especially with high concentrations or non-aqueous solvents, you should use volumetric flasks and measure the final volume directly. Also, the equation assumes temperature is constant; molarity changes with temperature because volume changes. For precise work, prepare solutions at the temperature you will use them.

Another limit: the equation cannot be used for serial dilutions that involve multiple steps unless you apply it step by step. For a serial dilution, you would calculate each step’s final volume separately.

Frequently Asked Questions

Is M1V1 = M2V2 the same as C1V1 = C2V2? Yes, they are the same formula. The letter M stands for molarity, and C stands for concentration. Both are used interchangeably; C is more general because it can represent any concentration unit, while M specifically means mol/L.

Can I use M1V1 = M2V2 for percent solutions? Yes, as long as the percent concentration is on a volume/volume or mass/volume basis and the same units are used on both sides. For example, a 10% v/v solution diluted to 5% v/v works fine. For mass/mass percent, it is better to use mass-based calculations because volume changes with density.

What if I need to find M1 instead of V2? Rearrange the equation to M1 = M2 × V2 / V1. For example, if you have 50 mL of a diluted solution at 0.2 M that came from 10 mL of stock, the stock concentration is (0.2 × 50) / 10 = 1.0 M.

Does the equation work with volumes in liters and milliliters mixed? No, you must use the same unit for V1 and V2. If V1 is in mL and V2 is in L, convert one to the other before calculating. The equation is unit-consistent only when both volumes share the same unit.

Why do I get a different answer when I use the calculator versus my manual calculation? Check your units and your rearrangement. The calculator uses the formula V2 = M1 × V1 / M2. If you entered M1 = 1, V1 = 10, M2 = 0.25, you get 40 mL. If you accidentally entered V1 as 0.01 L (thinking in liters), you would get 0.04 L, which is the same as 40 mL. So ensure you are comparing the same units.

Related

Formula used
in m | Initial concentration (M1) | mol/L | 1.0 | 0
in v | Initial volume (V1) | mL | 10 | 0
in m2 | Final concentration (M2) | mol/L | 0.25 | 0
out v2 | Final volume (V2) | mL | m * v / m2 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →