molecalculator

Moles & Molar Mass

Wheel Load Analysis Calculator & How to Use It

Calculator No. 01-10062 · Updated · Formula and assumptions shown below

Front axle load 10,000.00 kg
Rear axle load
10,000.00 kg
= Total weight × Center of gravity from front axle ÷ Wheelbase
Front axle load percentage
50.00 %
= (Wheelbase − Center of gravity from front axle) ÷ Wheelbase × 100
Total weight
20000 kg
Set in the form below
You enter
Total weight (kg), Center of gravity from front axle (m), Wheelbase (m)
You get
Front axle load (kg), Rear axle load (kg), Front axle load percentage (%)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A wheel load analysis calculator works out the load carried by each wheel of a vehicle or structure, based on the total weight and its center of gravity. You enter the total weight, the wheelbase or axle spacing, and the center of gravity position, and it returns the static load on each wheel or axle. This is essential for designing axles, tires, suspensions, and floor load ratings.

Formula

The calculator uses static equilibrium for a rigid body supported at two points. For a vehicle with a front axle and a rear axle:

  • Front axle load = Total weight × (wheelbase − center of gravity distance from front axle) / wheelbase
  • Rear axle load = Total weight × center of gravity distance from front axle / wheelbase

In symbols:

Ffront = W × (L − a) / L
Frear = W × a / L

Where:

  • W = total weight (kg or N)
  • L = wheelbase (m) – the horizontal distance between front and rear axle centers
  • a = horizontal distance from the front axle to the center of gravity (m)

The sum of the two axle loads always equals the total weight. If the center of gravity is exactly halfway, each axle carries half the weight. Moving the center of gravity forward increases the front load and decreases the rear load.

Worked Example

Using the default values: total weight = 20,000 kg, center of gravity 3 m from the front axle, wheelbase = 6 m.

Step 1: Calculate the distance from the center of gravity to the rear axle: 6 − 3 = 3 m.

Step 2: Front axle load = 20,000 × (6 − 3) / 6 = 20,000 × 3 / 6 = 10,000 kg.

Step 3: Rear axle load = 20,000 × 3 / 6 = 10,000 kg.

Step 4: Front load percentage = (3 / 6) × 100 = 50%.

The calculator shows 10,000 kg on each axle, 50% front. This matches the symmetrical center of gravity.

Assumptions

  • The vehicle is on level ground and at rest (static condition).
  • The structure is rigid – no suspension deflection or frame flex.
  • The center of gravity lies on the longitudinal centerline, so left and right wheels share the axle load equally.
  • The load is distributed only between the two axles – no third axle or trailer coupling.
  • Weight is measured in kilograms (mass) or Newtons (force); the calculator uses mass in kg, but the same formulas work with force in N.

When to Use a Wheel Load Calculator

You use this type of calculation in several engineering and logistical contexts:

  • Designing a new vehicle chassis or modifying an existing one – to select axle ratings, springs, and dampers.
  • Checking whether a truck or trailer exceeds legal axle weight limits on public roads.
  • Determining floor loading for industrial mezzanines, parking garages, or bridge decks – the wheel load is the point load the structure must support.
  • Positioning heavy equipment (e.g., a generator or tank) on a trailer so that the tongue load stays within the tow vehicle’s rating.
  • Balancing a forklift or crane counterweight – the center of gravity shifts with the load.

For a single wheel (not an axle), divide the axle load by the number of wheels on that axle (usually 2, but some heavy vehicles have dual tires that count as 2 or 4 contact patches).

How to Read the Results

The output gives the static load on each axle. In practice, you also need to consider dynamic effects: braking shifts load to the front, acceleration shifts it to the rear, and cornering transfers load side to side. The static calculation is the baseline; dynamic loads can be 20–50% higher.

For tire selection, compare the per-wheel load to the tire’s load index at the recommended inflation pressure. For suspension design, the axle load is the force the springs and dampers must support. For floor loading, the wheel load (plus a dynamic factor) is used to check the slab against punching shear and bending.

Common Mistakes and Misconceptions

  • Using the total weight instead of the axle load – always split the weight into front and rear before designing components.
  • Forgetting the center of gravity height – the calculator assumes a 2D side view; if the CG is high, the load transfer during cornering or braking must be added separately.
  • Assuming equal left/right distribution – if the load is off-center, each wheel gets a different load; you need the lateral CG position as well.
  • Mixing units – if you enter weight in pounds and wheelbase in meters, the result is meaningless. Convert all to consistent units (kg and m, or lb and ft).
  • Ignoring the difference between mass and force – on Earth, 1 kg weighs 9.81 N. Structural engineers often work in Newtons, while vehicle specs use kg. The calculator uses kg, but you can multiply by 9.81 to get Newtons.

Limitations and Real-World Adjustments

This static two-axle model is a simplification. Real vehicles have suspension that redistributes load when the wheels move vertically. A truck with air springs will have a different load distribution than a rigid axle. Also, the center of gravity is not always fixed – it moves when the vehicle is loaded with cargo or liquid sloshes.

For a three-axle vehicle (e.g., a tractor-trailer), you need a more complex model that considers the coupling forces. The same equilibrium principle applies, but you solve a system of equations with the fifth wheel or hitch reaction as an unknown.

If you are checking road legality, note that axle weight limits vary by jurisdiction and often include a separate limit for tandem or tridem axle groups. The calculator gives the theoretical static load; the actual scale reading may differ due to scale calibration and vehicle positioning.

How to Choose a Wheel Load Calculator

For most purposes, a simple two-axle calculator like this one is enough. But consider the following when selecting a tool:

  • Number of axles – some calculators handle 3 or more axles with a user-defined axle spacing.
  • Input method – do you know the center of gravity location, or do you have individual wheel loads from a scale? The latter is a direct measurement, not a calculation.
  • Dynamic factors – if you need to account for braking or cornering, look for a calculator that includes acceleration or lateral load transfer.
  • Unit support – check whether it handles imperial and metric units without manual conversion.
  • Output format – some give per-wheel loads, others only axle loads. You may need both.

Frequently Asked Questions

How do I find the center of gravity of my vehicle?

You can measure it by weighing the vehicle on scales at each wheel, then using the measured loads to back-calculate the CG location. The front axle load fraction equals (L − a)/L, so a = L × (1 − front load fraction). Alternatively, use a weighbridge that gives individual axle weights.

What is the difference between wheel load and axle load?

Axle load is the total weight supported by all wheels on one axle. Wheel load is the load on a single wheel. For a two-wheel axle, divide the axle load by 2. For dual tires, the load is shared between the two tires, but each tire still sees a portion of the wheel load.

Does this calculator work for trailers?

Yes, for a simple two-axle trailer. The tongue load acts as a third support point at the hitch. To find the tongue load, you need the trailer’s total weight and the distance from the hitch to the axle center. The formula is: tongue load = total weight × (distance from CG to axle) / (distance from hitch to axle). The axle load is the remainder.

Why is my calculated wheel load different from the scale reading?

Scales measure the actual reaction at each wheel, which includes any load transfer from suspension, frame twist, or an uneven surface. The calculator assumes a perfectly rigid, level vehicle. Also, if the vehicle is not exactly level, the CG shifts horizontally, changing the load distribution.

Can I use this for a single wheel like a wheelbarrow or a hand truck?

Yes, the same equilibrium applies. For a wheelbarrow, the two support points are the wheel and the handles. If you know the total weight and the distances from the CG to the wheel and to the handles, you can find the wheel load. The formula is the same: wheel load = total weight × (distance from CG to handles) / (distance from wheel to handles).

Safety and Accuracy Notes

Always verify your inputs with actual measurements – a small error in the center of gravity position can cause a large error in axle load. When checking road legality, use a certified weighbridge. For structural design, always include a safety factor and consult the relevant design code. This calculator is for educational and planning purposes; it does not replace professional engineering judgment.

Related

Formula used
in m | Total weight | kg | 20000 | 0
in d | Center of gravity from front axle | m | 3 | 0
in wb | Wheelbase | m | 6 | 0.1
out fa | Front axle load | kg | m * (wb - d) / wb | 2
out ra | Rear axle load | kg | m * d / wb | 2
out fp | Front axle load percentage | % | (wb - d) / wb * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →