Absorbance is proportional to concentration when light passes through a homogeneous sample under conditions where the Beer–Lambert law applies. This calculator uses absorbance, molar absorptivity, and path length to calculate concentration; enter absorbance, absorptivity, and path length, and it returns concentration in mol/L.
Formula
The Beer–Lambert law is A = εlc. Solving for concentration gives c = A / (εl). Here, A is absorbance (dimensionless), ε is molar absorptivity in L/(mol·cm), l is the optical path length through the sample in cm, and c is concentration in mol/L. The calculator’s second result converts mol/L to µmol/L by multiplying by 1,000,000.
Absorbance is defined as A = log10(I0/I), where I0 is the light intensity reaching the sample and I is the transmitted intensity. Absorbance itself is not a concentration; the law relates it to concentration through ε and l. Molar absorptivity depends on the absorbing substance, wavelength, solvent, and measurement conditions, so it is an input rather than a universal constant.
Worked Example
Using the defaults, A = 0.5, ε = 10,000 L/(mol·cm), and l = 1 cm.
- Calculate εl: 10,000 L/(mol·cm) × 1 cm = 10,000 L/mol.
- Divide absorbance by that value: c = 0.5 / 10,000 = 0.00005 mol/L.
- To six decimal places, the displayed concentration is 0.000050 mol/L. In micromolar units, 0.00005 mol/L × 1,000,000 = 50.00 µmol/L.
Assumptions
- The sample is sufficiently dilute and homogeneous for the Beer–Lambert relationship to be linear.
- The supplied molar absorptivity applies to the analyte, wavelength, solvent, and conditions used.
- The entered path length is the actual distance light travels through the sample.
- Absorbance is a corrected measurement, with appropriate blank and instrument baseline.
Why Absorbance Tracks Concentration
A dissolved absorbing molecule can remove some light at a particular wavelength. With more absorbing molecules in the beam, a larger fraction of the light is absorbed, so less is transmitted. For a fixed wavelength and path length, the Beer–Lambert law expresses this relationship as a straight-line proportionality: doubling concentration doubles absorbance, provided the sample remains in the law’s usable range and the other conditions do not change.
The path length matters because a longer route through the sample gives light more opportunities to interact with absorbing molecules. At fixed concentration, doubling path length also doubles absorbance under ideal conditions. Molar absorptivity describes how strongly a particular species absorbs at a chosen wavelength. A strongly absorbing substance can produce a measurable signal at a lower concentration than a weak absorber.
How to Use the Calculator
- Absorbance: enter the sample’s blank-corrected absorbance at the wavelength used to determine ε. Absorbance is dimensionless; do not enter percent transmittance in this field.
- Molar absorptivity: enter a value appropriate for the absorbing compound and measurement conditions, with units of L/(mol·cm). Obtain it from a reliable reference or determine it using a calibration method.
- Path length: enter the optical path through the sample in centimeters. A 10 mm path is 1 cm; a microvolume or nonstandard cell may have a different path length.
The first output is molar concentration. The second is the same concentration in micromolar units. If absorbance is zero, the calculated concentration is zero; negative absorbance is excluded here because it usually indicates a baseline, blank, or measurement issue rather than a meaningful negative concentration.
When Proportionality Can Fail
The relationship is a useful model, not a guarantee that every absorbance reading can be converted directly into concentration. At high concentrations, molecules may interact, the refractive properties of the solution may change, or chemical equilibria may shift. Scattering from particles, turbidity, stray light, and detector limitations can also bend the calibration relationship. Consequently, a sample’s absorbance may stop increasing in direct proportion to concentration.
Absorbing species can change form with pH, solvent, temperature, or binding interactions. If those changes alter the species’ spectrum, the ε value may no longer apply. A mixture of absorbers can contribute overlapping signals; a single absorbance measurement cannot generally separate their concentrations without additional wavelengths or other information.
For measurements intended to be quantitative, use a blank and a calibration curve made from standards of known concentration in a suitable range. The curve reveals whether absorbance is linear under the actual method and can account for practical differences in the setup. Dilute an over-range sample and repeat the measurement when appropriate, then multiply the measured concentration by the dilution factor to recover the original concentration. Follow your lab method, the safety data sheet (SDS), and your supervisor.
Common Mistakes and Checks
- Using the wrong ε: absorptivity is wavelength- and condition-dependent. A value from a different wavelength or chemical form can lead to a systematically incorrect concentration.
- Mixing units: this calculator expects ε in L/(mol·cm) and path length in cm. If a source reports path length in millimeters, convert it to centimeters before entering it.
- Forgetting the blank: solvent, reagents, and the cell may absorb light too. A suitable blank helps isolate the sample’s absorbance.
- Treating transmittance as absorbance: if transmittance is expressed as a fraction T, then A = −log10(T). For percent transmittance, first divide the percentage by 100.
- Ignoring dilution: the result describes the solution measured in the cell. If that solution was diluted from an original sample, apply the dilution factor afterward.
Check that the calculated value agrees with the range of your standards and that replicate readings are reasonably consistent. Reporting more digits than the absorbance measurement, ε value, or path length justifies does not make the result more accurate.
Frequently Asked Questions
Is absorbance always directly proportional to concentration?
No. It is proportional under the Beer–Lambert law’s assumptions, over a suitable concentration range, with fixed wavelength and path length and a stable absorbing species. Real samples and instruments can depart from linearity.
What is the Beer–Lambert law in simple terms?
It states that absorbance equals molar absorptivity multiplied by path length and concentration: A = εlc. For fixed ε and l, increasing c increases A proportionally.
Can I calculate concentration from absorbance alone?
Not generally. You also need the relevant molar absorptivity and path length, or a calibration curve that relates measured absorbance to known concentrations under the same conditions.
What happens if I double the path length?
In the linear Beer–Lambert range, absorbance doubles at the same concentration and wavelength. A longer path can help measure dilute samples, but it can make concentrated samples exceed the useful measurement range.
Why is my absorbance not linear with concentration?
Possible causes include excessive concentration, scattering or turbidity, an unsuitable blank, stray light, an incorrect wavelength, or a change in the absorbing species. Check standards and the measurement conditions before relying on a direct calculation.
Related
Formula used
in a | Absorbance | - | 0.5 | 0 in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0.000001 in l | Path length | cm | 1 | 0.000001 out c | Concentration | mol/L | a / (eps * l) | 6 out cm | Concentration | µmol/L | c * 1000000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Cell Culture Doubling Time Equation and Calculator24.00 h
- Cell Culture Seeding Density Calculator and Formula4,000.00 cells/cm^2
- Cell Culture Doubling Time Calculator and Formula24.00 h
- Cell Culture Doubling Time Calculator and Formula24.00 h
- CFU From Dilution: Calculate Colony-Forming Units10,000,000 CFU/mL
- Zero Order Release Kinetics Calculator and Explanation5.000 mg/h