molecalculator

Moles & Molar Mass

Exponential Decay Rate Formula and How to Use It

Calculator No. 01-5196 · Updated · Formula and assumptions shown below

Amount remaining 36.7879 units
Fraction remaining
0.367879 fraction
Result, rounded to 6 decimal places
Percent remaining
36.79 %
Result, rounded to 2 decimal places
Starting amount
100 units
Set in the form below
You enter
Starting amount (units), Decay constant k (1/time), Elapsed time (time)
You get
Amount remaining (units), Fraction remaining (fraction), Percent remaining (%)
Rounding
4 dp · 6 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The exponential decay rate formula is A(t) = A₀e−kt, where A₀ is the starting amount, t is elapsed time, and k is the positive decay constant. This calculator finds the remaining amount from those three inputs; its headline result is A(t), in the same units as A₀.

Formula

The remaining amount is the initial amount multiplied by the exponential of the negative decay constant times elapsed time:

A(t) = A₀e−kt

  • A(t) is the amount remaining at time t, in the same units as A₀.
  • A₀ is the amount at t = 0, in any nonnegative amount unit.
  • e is Euler’s number, approximately 2.71828.
  • k is the positive decay constant, expressed as inverse time, such as s−1 or day−1.
  • t is elapsed time, expressed in the time unit that matches k.

The calculator’s formula is A(t) = a0 × exp(−k × t). Its additional outputs are the remaining fraction, e−kt, and the percentage remaining, 100e−kt. The amount lost is A₀ − A(t), and the percentage lost is 100% minus the percentage remaining.

Worked Example

Using the calculator’s defaults, the starting amount is 100 units, the decay constant is 0.1 per time unit, and elapsed time is 10 time units. The units of time cancel in kt:

kt = (0.1 time−1)(10 time) = 1

Substitute that result in the exponential model:

A(10) = 100 × exp(−1) = 100 × 0.36787944 = 36.787944

Rounded to the calculator’s four decimal places, 36.7879 units remain. The remaining fraction is exp(−1) = 0.367879, or 36.79% when expressed as a percentage and rounded to two decimal places. Thus, 63.21% of the starting amount has decayed. These figures describe the model, not a claim that every physical process follows it exactly.

Assumptions

  • The amount follows a single exponential decay process with a constant k over the interval.
  • The decay constant and elapsed time use reciprocal, matching time units; for example, day−1 with days.
  • The starting amount is nonnegative, and the process is modeled continuously. The formula approaches zero but does not reach it at any finite time.

What the Decay Constant Means

The constant k sets how quickly the amount falls. A larger k means faster decay. Its units must be the inverse of the time unit used for t: if k is 0.1 per hour, t must be in hours. If time is instead given in minutes, convert k to 0.1/60 per minute, or convert the elapsed time to hours. Using mismatched units changes the exponent and can produce a completely wrong result.

For a constant-rate exponential process, the instantaneous rate of change is proportional to the amount present:

dA/dt = −kA

The negative sign indicates that A decreases. Solving this differential equation gives A(t) = A₀e−kt. The absolute rate of loss at a particular moment is kA; the fractional rate of loss is k per unit time. This distinction matters: a constant k does not mean the same number of units disappears every hour. As the amount becomes smaller, the absolute amount lost per hour also becomes smaller.

Half-Life and Other Useful Forms

The half-life, t1/2, is the time required for the amount to fall to half its starting value. Set A(t)/A₀ = 1/2 in the decay equation and solve for t:

t1/2 = ln(2)/k

Conversely, if a half-life is known, calculate the decay constant using k = ln(2)/t1/2. The half-life and k must use compatible time units. For example, a half-life of 5 days corresponds to k = 0.138629 per day; after 10 days, the model predicts two half-lives have passed and one quarter remains.

Another form uses the time constant τ = 1/k: A(t) = A₀e−t/τ. After one time constant, approximately 36.79% remains. The time constant is not the half-life; the half-life is about 0.693τ.

When the Formula Applies—and When It Does Not

Exponential decay is useful when the rate of loss is proportional to the amount currently present and the proportionality stays approximately constant. It appears in idealized models of radioactive decay, first-order chemical kinetics, and some cooling or discharge processes under specified conditions. The equation is a model, so choosing it requires evidence that its assumptions fit the situation.

Real processes can depart from a single exponential because conditions change, multiple mechanisms act at once, material is replenished, or the rate depends on concentration in a different way. A chemical reaction, for instance, is not necessarily first order; its rate law must be established for that reaction and those conditions. A fitted value of k is meaningful only for the data and conditions from which it was obtained.

For measurements at two times, with positive amounts A₁ and A₂ and elapsed interval Δt, the constant-rate model gives k = ln(A₁/A₂)/Δt. This calculation assumes the same exponential behavior throughout the interval. Measurement uncertainty, background signal, or an amount near a detection limit can make a fitted rate unreliable. Do not force the model through zero if the measured signal includes a non-decaying background; account for that baseline appropriately.

Common Mistakes

  • Using a negative k in this version: k is entered as a positive decay constant; the minus sign is already in the exponent. A negative k describes exponential growth under this equation’s sign convention.
  • Mixing time units: k in per second requires t in seconds. Convert one value before calculating.
  • Confusing amount remaining with amount lost: the calculator reports what remains. Subtract it from A₀ to find the amount lost.
  • Assuming a fixed absolute loss: exponential decay removes a fixed proportion over equal time intervals, not a fixed number of units.
  • Rounding too early: keep full precision for intermediate steps and round the final result to a sensible precision for the input data.

Frequently Asked Questions

What is the exponential decay rate formula?
The standard form is A(t) = A₀e−kt. A₀ is the initial amount, k is the positive decay constant, and t is elapsed time in matching units.

How do I calculate the decay rate constant?
If you know the half-life, use k = ln(2)/t1/2. If you know two positive amounts measured Δt apart under a constant exponential model, use k = ln(A₁/A₂)/Δt.

What units does the decay constant have?
It has inverse-time units, such as per second, per hour, or per year. Pair it with elapsed time in the corresponding unit so kt is dimensionless.

Is decay rate the same as half-life?
No. The decay constant k describes the fractional rate of decrease per unit time; half-life is a duration. They are related by t1/2 = ln(2)/k.

Can exponential decay reach zero?
In the continuous mathematical model, a positive starting amount gets arbitrarily close to zero but never equals zero at a finite time. A real measured amount may appear to be zero once it falls below a detection limit.

Why is my calculated amount increasing?
Check that k is positive and that the exponent includes −k × t. Also verify that the time and rate units match; a negative k in the decay formula produces growth instead.

Related

Formula used
in a0 | Starting amount | units | 100 | 0
in k | Decay constant k | 1/time | 0.1 | 0
in t | Elapsed time | time | 10 | 0
out a | Amount remaining | units | a0 * exp(-k * t) | 4
out f | Fraction remaining | fraction | exp(-k * t) | 6
out p | Percent remaining | % | 100 * exp(-k * t) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →