The NIST Chemistry WebBook provides an electron-ionization (EI) mass spectrum for acetone, also called propanone, under its entry for CAS Registry Number 67-64-1. The spectrum is recognized by a strong fragment at m/z 43 and a molecular ion at m/z 58; use the WebBook’s displayed or downloadable data for exact relative intensities and measurement details.
Formula
This calculator converts a selected mass-to-charge ratio into an approximate ion mass, using an assumed charge magnitude, and calculates the expected m/z of the singly charged acetone molecular ion from its molar mass. For an ion with charge magnitude z, m/z = ion mass in unified atomic mass units divided by z. Conversely, ion mass ≈ (m/z) × z. The proton mass, approximately 1.007276 u, is used only for the approximate ion-mass conversion shown here; it is not a correction to apply to every EI fragment.
- x is the observed m/z, entered as a number.
- m is the magnitude of the ion charge in elementary-charge units; ordinary EI ions are usually singly charged, so use 1.
- mm is acetone’s average molar mass, 58.08 g/mol, calculated from the standard atomic weights C = 12.011, H = 1.008 and O = 15.999: 3(12.011) + 6(1.008) + 15.999 = 58.080 g/mol.
The output labelled “Calculated m/z” is x/m; it is therefore the input normalized by charge, not an independently predicted spectrum. “Approximate ion mass” multiplies that value by 1.007276 u per charge. The separate reference value for acetone’s neutral molecular mass is its molar mass expressed numerically in u, about 58.08 u per molecule. These related quantities should not be confused.
Worked Example
For the default input, x = 43 and m = 1:
- Calculated m/z = 43 / 1 = 43.000.
- Approximate ion mass = 43.000 × 1.007276 = 43.313 u.
- Acetone’s neutral molecular mass from the listed atomic weights is 58.080 u; a singly charged molecular ion appears near nominal m/z 58.
The first two results describe the entered peak under the specified charge assumption. They do not identify its chemical structure or reproduce the NIST spectrum.
What the NIST Acetone Spectrum Shows
Acetone’s formula is C3H6O. In the commonly referenced EI spectrum, the base peak—the most intense peak, assigned relative intensity 100 in a normalized spectrum—is at nominal m/z 43. This prominent ion is commonly assigned to the acylium ion CH3CO+, also written C2H3O+. A signal at nominal m/z 58 corresponds to the acetone molecular ion, C3H6O+·, formed when the molecule loses an electron.
Other fragment peaks can occur, including signals associated with smaller hydrocarbon ions. Their exact intensities depend on the recorded spectrum and acquisition conditions. The two familiar nominal values, 43 and 58, are useful for orientation, but they do not give a full peak list or establish exact-mass assignments. Do not treat approximate peak descriptions as a substitute for the actual reference record.
How to Find and Read the NIST Record
Search the NIST Chemistry WebBook for acetone or CAS 67-64-1, then open the mass spectrum associated with the compound record. Confirm that the entry is acetone rather than another substance with a similar name. The site may present a plot, tabular peak information, or downloadable data; use the linked record to check which representation and conditions apply.
In a mass spectrum, the horizontal axis is m/z, mass-to-charge ratio, while the vertical axis reports relative abundance or intensity. A normalized base peak is set to 100, and other peaks are shown relative to it. Thus a peak at 43 that is taller than the peak at 58 means the fragment is more abundant in the detected ion signal under those measurement conditions—not that acetone molecules have a greater mass of 43.
- Check the ionization method, commonly EI for a conventional library spectrum.
- Read the axis labels and whether intensity is normalized.
- Check whether values are nominal-mass or high-resolution data.
- Keep the record’s experimental notes with any data copied into a report or comparison.
Why Acetone Produces a Strong Peak at 43
EI supplies enough energy to remove an electron and leave an energetic molecular ion. That ion can break apart. For acetone, cleavage around the carbonyl-containing structure produces the relatively stable CH3CO+ fragment, explaining why nominal m/z 43 is so prominent. The molecular ion at 58 is still important: it indicates the intact molecule’s nominal mass, even if its signal is less intense than the main fragment.
This is a useful example of a general mass-spectrometry principle: the largest peak is not necessarily the molecular ion. A library search or compound identification should consider the whole pattern, the molecular ion where visible, and other evidence such as retention time or an orthogonal analytical method. A single peak at 43 is not unique to acetone.
Common Interpretation Mistakes and Limits
Nominal m/z values are rounded to whole-number mass units. They are suitable for recognizing familiar peaks but cannot distinguish all ions with the same nominal mass. For example, accurate-mass analysis uses more precise measurements and candidate elemental compositions; the simple calculator above cannot perform that assignment.
- Confusing mass with m/z: they are numerically similar for a singly charged ion, but differ for multiply charged ions.
- Calling 43 the molecular ion: for acetone, 43 is a prominent fragment; the molecular ion is near 58.
- Comparing intensities across different spectra: normalization and operating conditions can change relative peak heights.
- Assuming one spectrum is universal: ion source settings, instrument design, sample state and data processing can affect the appearance.
The calculator assumes a charge magnitude supplied by the reader and reports only a basic mass conversion. It does not retrieve NIST data, predict fragmentation, account for isotope patterns, or certify an unknown sample’s identity. Use the reference spectrum and its metadata when exact peak positions or intensities matter.
Frequently Asked Questions
What is the base peak in acetone’s NIST mass spectrum?
The familiar EI reference pattern has its base peak at nominal m/z 43, commonly assigned to CH3CO+. Check the particular NIST record and spectrum display for its plotted data.
What is acetone’s molecular ion peak?
The molecular ion is near nominal m/z 58 for the singly charged EI molecular ion C3H6O+·. It may be less intense than the fragment peak at 43.
What is the NIST WebBook CAS number for acetone?
Acetone, or propanone, has CAS Registry Number 67-64-1. Searching by this number helps distinguish it from similarly named compounds.
Does a peak at m/z 43 prove a sample is acetone?
No. Other compounds can produce ions at nominal m/z 43. Identification requires comparing a broader pattern and, where appropriate, additional analytical evidence.
Why might my acetone spectrum differ from the NIST plot?
Different ionization settings, instruments, sample conditions, calibration, and processing can affect peak intensities or measured positions. Compare like methods and inspect the reference record’s conditions before drawing conclusions.
Assumptions
- The calculator treats the entered charge as a positive charge magnitude and assumes the specified ion has that charge.
- Acetone’s formula is C3H6O; its average molar mass is 58.080 g/mol using the atomic weights stated above.
- The characteristic 43 and 58 values are nominal EI-spectrum values, not a promise of exact measured positions or intensities for every instrument.
- This is reference-data interpretation and arithmetic only. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Related
Formula used
in x | Observed m/z | m/z | 43 | 0 in m | Ion charge magnitude | elementary charges | 1 | 1 in mm | Acetone molar mass | g/mol | 58.08 | 0.001 out mz | Calculated m/z | m/z | x / m | 3 out mass | Approximate ion mass | u | mz * 1.007276 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %