molecalculator

Moles & Molar Mass

Air Density by Altitude: Table and Calculator

Calculator No. 01-3670 · Updated · Formula and assumptions shown below

Air density 1.225 kg/m^3
ISA pressure
101,325 Pa
Result, rounded to a whole number
Altitude above sea level
0 m
Set in the form below
Air temperature
15 °C
Set in the form below
You enter
Altitude above sea level (m), Air temperature (°C)
You get
Air density (kg/m^3), ISA pressure (Pa)
Rounding
3 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An air density table by altitude shows how the mass of air in a given volume generally decreases as elevation rises. This calculator estimates density from altitude and air temperature using the International Standard Atmosphere (ISA) in the troposphere; enter altitude in metres and temperature in °C to get air density in kg/m³.

Formula

The calculator uses the ideal-gas density relation, density = pressure divided by the specific gas constant for dry air times absolute temperature: ρ = p / (RdT). Here ρ is air density in kg/m³, p is pressure in pascals (Pa), Rd is the specific gas constant for dry air, 287.05287 J/(kg·K), and T is absolute temperature in kelvins (K).

Because altitude alone does not determine actual weather, pressure is estimated with the ISA troposphere model. For altitude h in metres, up to 11,000 m, ISA temperature is TISA = 288.15 − 0.0065h K, and pressure is p = 101325 × (TISA/288.15)5.2558797 Pa. The exponent comes from the standard atmosphere and the hydrostatic ideal-gas model. The calculator uses this pressure, but uses the entered air temperature for density: ρ = p/[287.05287(t + 273.15)]. Temperature t is entered in °C; the conversion to kelvins is +273.15.

This distinction matters: the ISA pressure estimate is tied to the standard atmosphere, while the actual pressure at a location can differ with weather. The output is therefore a useful estimate, not a substitute for a pressure measurement or a full weather observation.

Worked Example

Using the defaults, altitude h = 0 m and temperature t = 15 °C:

  1. ISA pressure: p = 101325 × (1 − 0.0065 × 0 / 288.15)5.2558797 = 101325 Pa.
  2. Convert temperature: T = 15 + 273.15 = 288.15 K.
  3. Density: ρ = 101325 / (287.05287 × 288.15) = 1.225000? kg/m³, or 1.225 kg/m³ to three decimal places.

The first output is therefore 1.225 kg/m³. This is the familiar standard sea-level density to the displayed precision.

Assumptions

  • Air is treated as dry and as an ideal gas.
  • Pressure follows the ISA troposphere model, with sea-level pressure 101325 Pa and the standard temperature lapse rate of 0.0065 K per metre.
  • Altitude is geometric height above sea level, and is limited here to 0–11,000 m.
  • The entered temperature is in °C and is converted to kelvins. It must be above absolute zero; the ISA pressure estimate does not adjust to the entered temperature.

Air Density Table by Altitude

The following reference values use the ISA temperature and pressure together. They are rounded examples, not universal measurements; actual density varies with pressure, temperature, humidity and weather.

  • 0 m: approximately 1.225 kg/m³
  • 1,000 m: approximately 1.112 kg/m³
  • 2,000 m: approximately 1.007 kg/m³
  • 3,000 m: approximately 0.909 kg/m³
  • 5,000 m: approximately 0.736 kg/m³
  • 8,000 m: approximately 0.525 kg/m³
  • 10,000 m: approximately 0.413 kg/m³
  • 11,000 m: approximately 0.364 kg/m³

These values are consistent with the standard-atmosphere model and show the general trend, not a fixed density for every place at that elevation. Density is mass per unit volume, so a cubic metre of air contains less mass as pressure falls with altitude. The decrease is not linear: each additional kilometre does not remove the same amount of density.

How Altitude, Temperature, and Pressure Affect Density

Altitude is a convenient way to estimate density only when a standard atmosphere is assumed. As altitude increases, the weight of the air above a location decreases, so pressure generally falls. At the same pressure, warmer air is less dense than colder air because the same gas occupies more volume at higher temperature. The ideal-gas relation captures both effects: density rises with pressure and falls with absolute temperature.

Humidity also affects real air density. At the same pressure and temperature, moist air is slightly less dense than dry air because water molecules have lower molar mass than the average molecules in dry air. This calculator omits humidity. For aviation, engineering, or scientific work requiring close accuracy, use the relevant measured pressure, temperature and humidity, and apply the applicable standard or correction method.

A common misconception is that a listed altitude gives a precise density. It does not: a high-pressure weather system can produce different conditions from a low-pressure system at the same elevation. Also, “density altitude” is a related aviation term describing the altitude in the standard atmosphere that corresponds to a given air density; it is not simply the physical height above sea level.

Using the Calculator and Reading the Result

Enter altitude above sea level in metres and the local air temperature in degrees Celsius. The calculator returns estimated density in kg/m³ and the ISA pressure used in pascals. At 0 m and 15 °C, the default result is 1.225 kg/m³. For a warmer day at the same altitude, density will be lower; for a higher altitude at a similar temperature, the model will generally return lower density because its estimated pressure falls.

To compare the result with a table, make sure both use the same assumptions. A standard-atmosphere table usually pairs standard pressure with standard temperature. If you enter a measured temperature while retaining ISA pressure, the output is a hybrid estimate, not the exact density of the current air mass. For greater accuracy, use measured local pressure rather than an altitude-derived standard pressure.

Limits, Units, and Common Errors

  • Temperature conversion: the formula requires kelvins, not Celsius. The calculator adds 273.15; do not add it again to the displayed input.
  • Pressure units: the pressure formula returns Pa. If using the ideal-gas equation yourself, keep pressure, gas constant and volume units consistent.
  • Altitude range: this model is restricted to 0–11,000 m, the ISA troposphere layer represented here. Do not extrapolate the formula above its stated range.
  • Weather variation: standard pressure at a given altitude is not necessarily the measured pressure. Weather and local conditions can noticeably change the estimate.
  • Humidity and composition: the calculation assumes dry air with a fixed gas constant; moist air and unusual gas mixtures need an appropriate model.
  • Rounding: table values are rounded and may differ in the last digits from a calculation using more precise constants.

Air density is useful in estimating aerodynamic forces, buoyancy, ventilation loads and gas behavior, but those applications may require additional factors such as wind, geometry, compressibility or humidity. Treat this result as a basic atmospheric estimate, not as a complete design or safety calculation.

Frequently Asked Questions

What is the density of air at sea level?
In the ISA standard atmosphere at 15 °C and 101325 Pa, dry-air density is about 1.225 kg/m³. Actual sea-level density changes with temperature, pressure and humidity.

How much does air density decrease with altitude?
It decreases nonlinearly as atmospheric pressure falls. In the ISA table, density is about 1.225 kg/m³ at sea level and 0.736 kg/m³ at 5,000 m; local conditions can differ.

Does temperature change air density at the same altitude?
Yes. At a fixed pressure, warmer air has lower density and colder air has higher density. Temperature must be expressed in kelvins in the ideal-gas equation.

Is this an actual air density table for every location?
No. It is an ISA reference estimate. Actual pressure, temperature and humidity vary, so a measured-condition calculation is needed when precision matters.

What is the difference between altitude and density altitude?
Altitude is physical height above a reference level, commonly sea level. Density altitude is the standard-atmosphere altitude corresponding to the current air density, and can differ from physical elevation.

Related

Formula used
in h | Altitude above sea level | m | 0 | 0 | 11000
in t | Air temperature | °C | 15 | -273.15
out rho | Air density | kg/m^3 | 101325 * (1 - 0.0065 * h / (288.15)) ^ 4.2558797 / (287.05287 * (t + 273.15)) | 3
out p | ISA pressure | Pa | 101325 * (1 - 0.0065 * h / 288.15) ^ 5.2558797 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →