molecalculator

Moles & Molar Mass

Brix to Concentration: Convert °Bx to Sugar Content

Calculator No. 01-5368 · Updated · Formula and assumptions shown below

Sucrose-equivalent concentration 125.5 g/L
Sucrose-equivalent concentration
120.0 g/kg
= Brix reading × 10
Brix reading
12 °Bx
Set in the form below
Solution density
1.046 g/mL
Set in the form below
You enter
Brix reading (°Bx), Solution density (g/mL)
You get
Sucrose-equivalent concentration (g/L), Sucrose-equivalent concentration (g/kg)
Rounding
1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A Brix-to-concentration calculator estimates the mass concentration of sucrose in a solution from its °Bx reading: for a pure sucrose–water solution, °Bx is approximately grams of sucrose per 100 grams of solution. Enter a Brix value and the solution’s density to calculate sucrose-equivalent concentration in g/L; the result is not a universal measurement of every dissolved substance.

Formula

For a sucrose solution, °Bx is the mass percentage of sucrose: °Bx = 100 × mass of sucrose ÷ mass of solution. To convert that mass fraction to a volume-based concentration, multiply by the solution density:

Concentration (g/L) = (°Bx ÷ 100) × density (g/mL) × 1000 mL/L.

Here, °Bx is the refractometer reading expressed on the sucrose scale, density is the solution’s mass per volume in g/mL, and 1000 mL/L converts milliliters to liters. The calculator also reports g/kg, calculated as °Bx × 10, because a mass percentage gives grams of sucrose-equivalent material per 100 grams of solution.

Worked Example

Using the defaults, the reading is 12 °Bx and density is 1.046 g/mL.

  1. Convert the Brix percentage to a mass fraction: 12 ÷ 100 = 0.12.
  2. Multiply by density and convert mL to L: 0.12 × 1.046 g/mL × 1000 mL/L = 125.52 g/L.
  3. Round to the calculator’s one decimal place: 125.5 g/L.
  4. For the mass-based result: 12 × 10 = 120.0 g/kg.

Assumptions

  • The sample is a sucrose–water solution, or the result is understood as sucrose-equivalent rather than the actual concentration of another solute.
  • The entered density applies to the same sample and measurement temperature as the Brix reading.
  • Density is expressed in g/mL; the factor of 1000 converts mL to L.
  • This is a calculation for study and lab planning, not a substitute for a validated method when composition or accuracy matters.

What °Brix Measures

Degrees Brix originated as a way to describe the sucrose content of aqueous solutions by mass. A reading of 12 °Bx corresponds, under the sucrose calibration, to 12 g sucrose per 100 g of solution. It is a mass fraction, not automatically grams per liter, grams per milliliter, or grams of sugar per 100 mL.

That distinction explains why density is needed for the g/L conversion. One liter of a solution generally weighs more than one kilogram if its density is above 1 g/mL. At 12 °Bx and 1.046 g/mL, the solution contains 120 g sucrose-equivalent per kilogram, and each liter weighs 1.046 kg; multiplying the mass fraction by that liter’s mass gives 125.52 g/L.

Refractometers infer Brix from how a sample bends light. The instrument typically displays a sucrose-equivalent value based on a calibration relationship. A Brix reading is therefore strongest as a direct sucrose estimate in a mostly sucrose-and-water mixture, not as a universal assay for any liquid.

When a Brix Conversion Is Useful

Converting °Bx to g/L can help compare concentration values reported in different units, estimate the amount of sucrose-equivalent material in a known volume, or prepare a calculation that requires mass per volume. It is useful only when the Brix reading and density refer to the same sample and conditions.

  • Use °Bx directly when the question concerns mass percent or a sucrose-calibrated refractometer reading.
  • Use g/kg when the desired basis is mass of solution. For example, 12 °Bx corresponds to 120 g/kg on the sucrose scale.
  • Use g/L when the desired basis is volume. Include density rather than assuming that one liter weighs exactly one kilogram.
  • Use an appropriate analytical method when you need the actual concentration of a specific non-sugar compound or a mixture with important interfering components.

Limits and Common Conversion Mistakes

The main limitation is that Brix is not a direct measurement of total dissolved solids for every possible sample. Acids, salts, alcohols, and other dissolved substances can change refractive index. In a mixed liquid, a refractometer may still show a °Bx value, but it is generally an apparent or sucrose-equivalent reading. The calculator cannot identify which substances caused the reading or separate their contributions.

Another common error is treating °Bx as g/L. A value of 12 °Bx means approximately 12 g sucrose per 100 g solution, not 12 g per 100 mL. The volume-based concentration depends on density. Assuming density is exactly 1.000 g/mL gives 120 g/L in this example, whereas the supplied density of 1.046 g/mL gives 125.5 g/L.

Temperature also matters. Refractive index and liquid density vary with temperature, and instruments may apply their own temperature compensation. Use density at a compatible temperature and follow the instrument’s correction guidance. Avoid reporting more precision than the reading, density measurement, and calibration support.

For fruit juice, syrups, fermentation samples, and other mixtures, Brix may be useful for process monitoring, but it should not automatically be called the true sugar concentration. A specific method—such as a validated chemical assay or a method designed for that sample type—may be needed for an accurate composition measurement. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

How do I convert Brix to g/L?
Multiply the Brix value divided by 100 by the solution density in g/mL, then multiply by 1000. For example, 12 °Bx at 1.046 g/mL gives 125.52 g/L sucrose-equivalent.

Is 1 °Bx equal to 10 g/L?
Not exactly. One °Bx corresponds to about 10 g sucrose per kilogram of solution. The g/L value depends on density; at 1.000 g/mL it is about 10 g/L, but a denser solution gives a higher value per liter.

Does Brix equal sugar concentration?
It is a good approximation for sucrose dissolved in water. In liquids containing other sugars or dissolved compounds, Brix is a sucrose-equivalent refractive reading and may not equal the actual total sugar concentration.

Can I convert Brix to molarity?
Not from Brix alone. A molarity calculation needs the identity and molar mass of the solute, plus a valid concentration estimate and solution volume basis. For a mixed sample, Brix does not reveal the amount of each compound.

Do I need density to convert °Bx to g/kg?
No. On the sucrose mass-percent scale, multiply °Bx by 10 to get g/kg. Density is needed to convert that mass-based concentration to g/L.

Related

Formula used
in bx | Brix reading | °Bx | 12 | 0 | 100
in rho | Solution density | g/mL | 1.046 | 0.001
out c | Sucrose-equivalent concentration | g/L | (bx / 100) * rho * 1000 | 1
out g | Sucrose-equivalent concentration | g/kg | bx * 10 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →