molecalculator

Moles & Molar Mass

Cubic Meters per Hour to Liters per Second

Calculator No. 01-6478 · Updated · Formula and assumptions shown below

Flow rate 0.2778 L/s
Flow rate
16.6667 L/min
= Flow rate × 60
Flow rate
1 m³/h
Set in the form below
You enter
Flow rate (m³/h)
You get
Flow rate (L/s), Flow rate (L/min)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a volumetric flow rate from cubic meters per hour (m³/h) to liters per second (L/s). Enter the flow rate in m³/h to get the equivalent L/s value, with the conversion factor and a worked example below.

Formula

To convert cubic meters per hour to liters per second, multiply the numerical flow rate by 1,000 liters per cubic meter, then divide by 3,600 seconds per hour:

Q (L/s) = Q (m³/h) × 1,000 ÷ 3,600, or equivalently Q (L/s) = Q (m³/h) ÷ 3.6.

  • Q (m³/h) is the input volumetric flow rate, in cubic meters per hour.
  • Q (L/s) is the converted flow rate, in liters per second.
  • 1,000 L/m³ converts cubic meters to liters.
  • 3,600 s/h converts hours to seconds.

The calculator also reports liters per minute using Q (L/min) = Q (L/s) × 60. These are unit conversions, not estimates: the factors are exact because a cubic meter contains 1,000 liters and an hour contains 3,600 seconds.

Worked Example

Using the calculator’s default input of 1 m³/h:

  1. Convert the volume unit: 1 m³/h × 1,000 L/m³ = 1,000 L/h.
  2. Convert the time unit: 1,000 L/h ÷ 3,600 s/h = 0.277777… L/s.
  3. Rounded to the calculator’s four decimal places, the result is 0.2778 L/s.
  4. For the additional output, 0.277777… L/s × 60 s/min = 16.6666… L/min, or 16.6667 L/min to four decimal places.

As a quick check, 0.277777… liters each second sustained for 3,600 seconds totals 1,000 liters, which is exactly 1 cubic meter.

What the Units Mean

A volumetric flow rate describes how much volume passes a point during a period of time. Cubic meters per hour is often used for larger flows or for equipment specifications stated over an hour; liters per second is convenient when considering flow over short intervals. The conversion changes only the units. It does not change the actual flow or say anything by itself about pressure, fluid speed, or the capacity of a pipe.

For example, a flow of 7.2 m³/h is 2 L/s, because 7.2 ÷ 3.6 = 2. Conversely, converting from L/s back to m³/h requires multiplying by 3.6. The direction matters: dividing by 3.6 makes the numerical value smaller when converting m³/h to L/s, while multiplying makes it larger in the reverse conversion.

When to Use This Conversion

This conversion is useful whenever two specifications describe the same volumetric flow in different units. It can help compare a measured flow with a design value, interpret a technical datasheet, or put a rate into units that suit a calculation. Check that both figures refer to the same fluid, operating conditions, and definition of flow before comparing them; a unit conversion cannot reconcile differences in those underlying conditions.

For a steady rate, volume over a period is found by multiplying flow rate by elapsed time, after making the time units consistent. At 2 L/s, for instance, the volume passing in 10 seconds is 20 L. If the flow changes over time, multiplying one instantaneous rate by the full duration may not give the total volume; the changing rate must be accounted for, such as by using an average rate when that average is appropriate.

Common Conversion Mistakes

  • Using 60 instead of 3,600: there are 3,600 seconds in an hour, not 60. The factor 60 applies to minutes per hour or seconds per minute, depending on the conversion.
  • Reversing the conversion: divide m³/h by 3.6 to get L/s; multiply L/s by 3.6 to get m³/h.
  • Mixing volume and flow units: m³ is a volume, while m³/h is a volume per time. Converting m³ alone does not produce a flow rate.
  • Rounding too early: keep extra digits during intermediate calculations and round the final result to the precision needed. The calculator displays four decimal places, but that does not mean the original measurement is accurate to four decimal places.
  • Assuming the rate is constant: a calculated volume over time is valid only when the rate is constant or when the chosen rate represents a suitable average.

Precision and Practical Interpretation

The mathematical conversion is exact, but a measured flow rate may have uncertainty. If a meter reports 1.0 m³/h, its measurement resolution and calibration determine how many digits are meaningful; displaying 0.2778 L/s does not remove that uncertainty. When comparing values, preserve the precision justified by the source measurement and note whether a value is measured, nominal, or a maximum rating.

Flow rate also differs from velocity. Velocity describes distance traveled per unit time, such as meters per second. For a full pipe with a known cross-sectional area, average velocity can be related to volumetric flow by Q = A × v, where Q is volume per time, A is area, and v is average velocity. A flow rate alone is therefore insufficient to calculate velocity unless the relevant area and flow conditions are known.

Frequently Asked Questions

How many liters per second is 1 m³/h?
1 m³/h equals 1,000 ÷ 3,600, or approximately 0.2778 L/s.

What is the fastest way to convert m³/h to L/s?
Divide the value in m³/h by 3.6. For example, 18 m³/h ÷ 3.6 = 5 L/s.

How do I convert liters per second to cubic meters per hour?
Multiply the L/s value by 3.6. For example, 5 L/s × 3.6 = 18 m³/h.

Is m³/h the same as m³ per hour?
Yes. The slash means “per,” so m³/h and m³ per hour express the same volume flow unit.

Does this conversion depend on the liquid or gas?
No. The unit conversion is the same for any fluid. However, the actual flow measurement or a flow stated at particular temperature and pressure may depend on the fluid and measurement conditions.

Related

Formula used
in q | Flow rate | m³/h | 1 | 0
out lps | Flow rate | L/s | q * 1000 / 3600 | 4
out lpm | Flow rate | L/min | lps * 60 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →