molecalculator

Moles & Molar Mass

Linear Thermal Expansion Calculator and Formula

Calculator No. 01-3334 · Updated · Formula and assumptions shown below

Change in length 0.000600 m
Final length
1.000600 m
= Original length + Change in length
Linear expansion coefficient
0.000012 1/K
Set in the form below
Original length
1 m
Set in the form below
You enter
Linear expansion coefficient (1/K), Original length (m), Temperature change (K)
You get
Change in length (m), Final length (m)
Rounding
6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate linear thermal expansion with ΔL = αL₀ΔT: multiply a material’s linear expansion coefficient by its original length and its temperature change. Enter those three values to get the change in length, plus the estimated final length; the result assumes the coefficient is constant across the temperature range.

Formula

The linear thermal expansion equation is ΔL = αL₀ΔT, and the estimated final length is Lf = L₀ + ΔL.

  • ΔL is the change in length, in metres (m).
  • α is the material’s linear expansion coefficient, in inverse kelvins (K−1). Its numerical value is the same when expressed per degree Celsius (°C−1).
  • L₀ is the original length, in metres (m).
  • ΔT is the temperature change, in kelvins (K), calculated as final temperature minus starting temperature.
  • Lf is the estimated final length, in metres (m).

The calculator’s coefficient default, 0.000012 K−1, is a representative approximate value for steel, not a universal value for all steels or conditions. Replace it with a reliable value for the specific material when accuracy matters. The expression uses SI units directly: coefficient × metres × kelvins produces metres.

Worked Example

Using the calculator’s default values, take α = 0.000012 K−1, L₀ = 1 m, and ΔT = 50 K.

  1. Calculate the length change: ΔL = αL₀ΔT = 0.000012 × 1 × 50 = 0.000600 m.
  2. Convert the change to millimetres: 0.000600 m × 1000 mm/m = 0.600 mm.
  3. Calculate the estimated final length: Lf = L₀ + ΔL = 1 + 0.000600 = 1.000600 m.

The calculator displays ΔL as 0.000600 m and Lf as 1.000600 m. These are idealized values based on the entered coefficient and temperature change.

Assumptions

  • The object is made of one uniform material and its measured length is the dimension of interest.
  • The coefficient α is treated as constant over the entire temperature change.
  • The material expands freely, without restraints, and remains intact; the calculation does not estimate stress, warping, or failure.
  • The temperature is uniform throughout the object and ΔT means final temperature minus initial temperature.

What Linear Thermal Expansion Means

Most solid materials change dimensions when their temperature changes. Heating generally increases the average spacing between atoms, making a solid longer; cooling generally reduces that spacing. The change is often small relative to the original dimension, which is why the equation uses the original length rather than repeatedly recalculating expansion at each step.

Linear expansion describes change along one dimension, such as the length of a rod, rail, pipe, or structural span. It does not directly calculate the change in area or volume. For an isotropic solid—a material with similar properties in every direction—and a modest temperature interval, approximate relationships are β ≈ 2α for area expansion and γ ≈ 3α for volume expansion. Those approximations are not substitutes for the appropriate coefficient and model when precision is required.

Choosing a Coefficient and Temperature Change

The coefficient depends on the material and can also vary with temperature, composition, processing, and direction. A value listed for one alloy, polymer, or ceramic should not automatically be applied to another. For anisotropic materials, including some crystals and composites, expansion can differ by direction; one scalar coefficient may then be inadequate.

Use a coefficient from a dependable materials reference or technical specification that matches the material and relevant temperature range. Check whether the source reports a linear coefficient and whether it is an average over a range or a value at a particular temperature. A coefficient quoted in µm/(m·K) can be entered as a number in K−1 after multiplying by 10−6; for example, 12 µm/(m·K) equals 0.000012 K−1.

For the temperature change, subtract the starting temperature from the ending temperature. A rise from 20 °C to 70 °C is ΔT = 50 °C, equivalent to 50 K. Temperature differences have the same numerical value in kelvins and degrees Celsius; do not add 273.15 to a temperature difference. That conversion applies when converting an absolute temperature between Celsius and kelvins, not when calculating ΔT.

How to Interpret the Result

A positive ΔL indicates lengthening under the entered conditions; a negative ΔL indicates shortening. The final length is the original length plus that signed change. For instance, the example predicts a 0.600 mm increase in a 1 m steel-like length for a 50 K rise. The result is not a statement that every steel part will change by exactly that amount: the chosen coefficient, actual temperature distribution, and constraints matter.

Real components may be held by fasteners, joined to other materials, or exposed to temperature gradients. Restraint can prevent free expansion and create thermal stress; different materials joined together can expand by different amounts and bend or load their connection. The length-change calculation alone does not determine those forces or deformation patterns. Engineering designs may need a structural or thermomechanical analysis.

Common Errors and Limits

  • Mixing units: use a coefficient in K−1 or °C−1, length in metres for this calculator, and a temperature difference in K or °C. Convert other units before entering them.
  • Using absolute temperature instead of a difference: enter the temperature rise or fall, not a temperature such as 70 °C by itself.
  • Choosing a generic coefficient: published values are material-dependent and often approximate. The calculator does not identify a material or verify a coefficient.
  • Overinterpreting precision: six displayed decimal places do not make the material data exact. Report only precision supported by the coefficient and measurements.
  • Assuming every material expands when heated: most common solids do over ordinary ranges, but some materials and temperature ranges behave unusually. Use verified data rather than assuming the sign or magnitude of α.

The equation is a first-order engineering approximation. If α changes substantially with temperature, a more accurate calculation integrates the temperature-dependent coefficient over the interval. Phase changes, large deformations, cracking, moisture changes, and nonuniform heating can also make this simple model unsuitable.

Frequently Asked Questions

What is the formula for linear thermal expansion?
Use ΔL = αL₀ΔT, where α is the linear expansion coefficient, L₀ is original length, and ΔT is the temperature change. Add ΔL to L₀ to estimate the final length.

Should I use Celsius or kelvins?
Either is suitable for a temperature difference: a change of 1 °C equals a change of 1 K. The coefficient must be expressed per matching temperature interval, and you should not convert a temperature difference by adding 273.15.

Can the expansion result be negative?
Yes. If the object cools, ΔT is negative, so a positive coefficient gives a negative ΔL: the length decreases. A material with a negative coefficient over a particular range can behave differently, so confirm the coefficient’s sign.

How do I calculate expansion in millimetres?
Calculate ΔL in metres using SI units, then multiply by 1000 to convert metres to millimetres. Alternatively, convert the original length to millimetres and keep the coefficient and temperature difference consistent.

Does this formula calculate thermal stress?
No. It estimates the free change in length. Stress depends on restraint, geometry, elastic properties, temperature distribution, and how the part is connected to other components.

Related

Formula used
in a | Linear expansion coefficient | 1/K | 0.000012 | 0
in l | Original length | m | 1 | 0
in t | Temperature change | K | 50 | 0
out dl | Change in length | m | a * l * t | 6
out lf | Final length | m | l + dl | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →