molecalculator

Moles & Molar Mass

Calculate Weak Acid pH: Formula and Example

Calculator No. 01-6031 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To calculate the pH of a weak acid, use its acid dissociation constant, Ka, and its starting concentration, C. For a monoprotic acid at 25 °C, the usual approximation is pH ≈ −log₁₀(√(Ka × C)); enter Ka and concentration in mol/L to get an estimated pH.

Formula

For a monoprotic weak acid, HA ⇌ H⁺ + A⁻. Its acid dissociation constant is Ka = [H⁺][A⁻]/[HA], and pH = −log₁₀[H⁺]. If the initial acid concentration is C and x dissociates, then [H⁺] = x, [A⁻] = x, and [HA] = C − x. Substitution gives Ka = x²/(C − x), or x² + Ka x − Ka C = 0. The positive root is x = (−Ka + √(Ka² + 4KaC))/2.

  • Ka is the dimensionless equilibrium constant for the acid dissociation reaction at a specified temperature.
  • C is the analytical starting concentration of the acid, in mol/L.
  • x is the equilibrium concentration of H⁺, in mol/L, under the model’s assumptions.
  • pH is −log₁₀(x), with x expressed as a concentration relative to the 1 mol/L standard state. In dilute introductory calculations, concentration is used as an approximation to activity.

When dissociation is small compared with C, C − x ≈ C. This gives x ≈ √(KaC), and pH ≈ −log₁₀(√(KaC)). The calculator uses the quadratic solution for its result, rather than relying on that approximation; the square-root expression is a useful quick estimate.

Worked Example

Using the calculator defaults, Ka = 1.8 × 10⁻⁵ and C = 0.1 mol/L:

  1. Calculate the discriminant: Ka² + 4KaC = (1.8 × 10⁻⁵)² + 4(1.8 × 10⁻⁵)(0.1) = 7.2324 × 10⁻⁶.
  2. Take its square root: √(7.2324 × 10⁻⁶) ≈ 0.002689312.
  3. Find x: (−0.000018 + 0.002689312)/2 ≈ 0.001335656 mol/L.
  4. Calculate pH: −log₁₀(0.001335656) ≈ 2.874.

The calculator therefore reports pH 2.874 to three decimal places. The quick approximation gives x ≈ √(1.8 × 10⁻⁵ × 0.1) ≈ 0.001341641 mol/L and pH ≈ 2.872, close to the quadratic result here.

Assumptions

  • The acid is monoprotic, and its initial solution contains the acid in water without other acids, bases, salts, or buffers affecting the equilibrium.
  • Ka is for the relevant acid at 25 °C; the default 1.8 × 10⁻⁵ is a conventional approximate value for acetic acid, not a universal weak-acid constant.
  • The solution is dilute enough that concentration approximates activity. Real pH depends on hydrogen-ion activity, temperature, and ionic strength.
  • The calculation is an equilibrium estimate, not a substitute for measurement. A pH meter reading is the real check; temperature and ionic strength can shift pH.

How to Use the Result

Choose the Ka for the particular acid and temperature, then enter the acid’s initial analytical concentration in mol/L. Do not enter pKa in the Ka field: pKa = −log₁₀(Ka), so convert with Ka = 10−pKa. For example, pKa 4.76 corresponds to Ka about 1.74 × 10⁻⁵. A larger Ka means a stronger acid and, at the same starting concentration, generally a lower pH.

Concentration means moles of acid per litre of final solution, not per litre of solvent before dissolving. If a value is supplied in millimolar, divide it by 1000 to obtain mol/L; for example, 25 mM = 0.025 mol/L. The output is an estimate for the equilibrium solution, not the pH of the undissolved acid or a guaranteed meter reading.

Check the Approximation

A common shortcut is x ≈ √(KaC). It is convenient, but should be checked against the small-dissociation assumption. Calculate the estimated fraction ionized, x/C. If it is no more than about 5%, the approximation is generally adequate for many classroom calculations; if it is larger, use the quadratic result. The 5% criterion is a practical rule of thumb, not a fundamental boundary.

For the example, x/C ≈ 0.001335656/0.1 ≈ 0.01336, or 1.34%, so the shortcut is reasonable. For a much more dilute solution, the acid can ionize to a substantial fraction of its starting amount, making C − x ≈ C inaccurate. The calculator’s quadratic expression accounts for that equilibrium depletion, but it still omits water autoionization and activity corrections.

Polyprotic Acids and Limits

Some acids can donate more than one proton. Their dissociation stages have separate constants, usually written Ka₁, Ka₂, and so on. For such acids, pH may be controlled mostly by the first dissociation, but not always: concentration, the relative Ka values, and later dissociations matter. Do not treat the total number of acidic hydrogens as one Ka or apply this monoprotic calculator unchanged to every polyprotic system.

Water also contributes a small hydrogen-ion concentration through its own equilibrium. It is usually negligible for a moderately concentrated weak-acid solution, but can matter when the acid is extremely dilute. Likewise, salts containing the conjugate base, added strong acid or base, and other dissolved electrolytes change the solution’s composition and may change the pH. Buffer mixtures require a calculation that includes both acid and conjugate base, often using the Henderson–Hasselbalch relation within its appropriate range.

Common Mistakes

  • Entering pKa as Ka: convert using Ka = 10−pKa; Ka values are often small decimals.
  • Mixing units: the concentration input must be mol/L, not mM, g/L, or mol/mL.
  • Using concentration as pH: pH is a negative logarithm, so a tenfold change in hydrogen-ion concentration changes pH by one unit.
  • Assuming weak means harmless or nearly neutral: “weak” describes incomplete dissociation, not necessarily a high pH or low hazard.
  • Rounding too early: retain several digits through the equilibrium calculation, then round the final pH to a precision justified by the input data.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. Handle acids with appropriate protective equipment and disposal practices; this calculation is for chemistry study and lab-planning arithmetic, not a safety assessment.

Frequently Asked Questions

What is the formula for the pH of a weak acid?
For a monoprotic acid with initial concentration C and Ka, solve x = (−Ka + √(Ka² + 4KaC))/2, then calculate pH = −log₁₀(x). If dissociation is small, x ≈ √(KaC) is a useful approximation.

Can I calculate weak-acid pH from pKa?
Yes. Convert pKa to Ka with Ka = 10−pKa, then use the acid concentration in mol/L. pKa and Ka are different forms of the same equilibrium information.

Does a weak acid always have a pH above 7?
No. A weak acid solution is generally acidic and can have a pH below 7. “Weak” means only that the acid dissociates partially in water; pH also depends on its concentration.

When should I use the quadratic equation instead of the square-root shortcut?
Use the quadratic when the estimated ionized fraction is not small compared with the initial concentration, or when you want the more accurate result under the monoprotic model. The shortcut is usually acceptable when x/C is about 5% or less.

Why does my measured pH differ from the calculation?
The model assumes an ideal dilute solution and a specified temperature. Activity effects, ionic strength, temperature, additional dissolved substances, contamination, and electrode calibration can all cause a difference. The pH meter reading is the practical check.

Related

Formula used
in ka | Acid dissociation constant Ka | - | 1.8e-5 | 0
in c | Initial acid concentration | mol/L | 0.1 | 0
out ph | Estimated pH | - | -log10((-ka + sqrt(ka^2 + 4 * ka * c)) / 2) | 3
out h | Equilibrium hydrogen ion concentration | mol/L | (-ka + sqrt(ka^2 + 4 * ka * c)) / 2 | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →