molecalculator

Moles & Molar Mass

Centrifugal Force Calculator: RPM to G-Force

Calculator No. 01-7359 · Updated · Formula and assumptions shown below

Relative centrifugal force (×g) 1,006.2 ×g
Acceleration (m/s²)
9,867.45 m/s²
= Relative centrifugal force (×g) × 9.80665
Rotor radius (cm)
10 cm
Set in the form below
Rotational speed
3000 RPM
Set in the form below
You enter
Rotor radius (cm) (cm), Rotational speed (RPM)
You get
Relative centrifugal force (×g) (×g), Acceleration (m/s²) (m/s²)
Rounding
1 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts RPM (revolutions per minute) into relative centrifugal force (RCF), commonly called g-force, for a centrifuge rotor. You enter the rotor radius (in centimeters) and the speed in RPM, and the calculator returns the g-force (×g) and the equivalent acceleration in m/s². The standard formula used is RCF = 1.118 × 10⁻⁵ × r × RPM², where r is the radius in centimeters.

Formula

The relationship between RPM and g-force is quadratic: doubling the speed quadruples the force. The standard formula used in centrifugation is:

RCF (×g) = 1.118 × 10⁻⁵ × r × (RPM)²

  • RCF – relative centrifugal force, expressed as multiples of Earth’s gravity (×g).
  • r – rotor radius in centimeters (cm). This is the distance from the center of the rotor to the sample.
  • RPM – rotational speed in revolutions per minute.

The constant 1.118 × 10⁻⁵ comes from converting RPM to radians per second and dividing by the standard gravity (9.80665 m/s²). If you prefer to work with the radius in millimeters, use RCF = 1.118 × 10⁻⁶ × r(mm) × RPM².

Worked Example

Using the default values from the calculator: radius = 10 cm, speed = 3000 RPM.

  1. Square the RPM: 3000² = 9,000,000.
  2. Multiply by the radius: 9,000,000 × 10 = 90,000,000.
  3. Multiply by the constant: 1.118 × 10⁻⁵ × 90,000,000 = 1006.2.
  4. The RCF is approximately 1006 ×g.

The calculator shows 1006.2 ×g, which rounds to 1006 ×g. To get m/s², multiply by 9.80665: 1006.2 × 9.80665 = 9867.5 m/s².

Assumptions

  • The radius is measured from the center of rotation to the sample’s position in the tube (often the midpoint or the bottom, depending on the rotor).
  • The rotor is spinning at a constant speed.
  • The formula assumes a fixed-angle or swing-bucket rotor where the sample’s radial distance is well-defined.
  • Gravity is taken as 9.80665 m/s² (standard).

Why RPM Alone Is Not Enough

A common mistake is comparing centrifugation runs by RPM only. Because g-force depends on the rotor radius, two centrifuges spinning at the same RPM can produce very different forces if their rotors have different diameters. For example, a microcentrifuge rotor with a 7 cm radius at 10,000 RPM gives 7826 ×g, while a large-capacity rotor with a 15 cm radius at the same speed gives 16,770 ×g. Protocols that specify g-force (e.g., “pellet at 10,000 ×g for 10 min”) are transferable between machines; RPM values are not.

For this reason, most centrifuge manuals provide a conversion chart or a rotor-specific table. When you read a protocol that says “spin at 5000 RPM,” you must check your rotor’s radius and convert to g-force if you want to reproduce the conditions on a different instrument.

How to Choose the Right Radius

The rotor radius is not a single fixed number for a centrifuge – it varies with the rotor type and the position of the sample. Here are the typical choices:

  • Maximum radius (rmax) – the distance from the center to the bottom of the tube when the tube is at its farthest position. This gives the highest g-force and is often used for pelleting.
  • Minimum radius (rmin) – the distance to the top of the tube (or the sample surface). This gives the lowest g-force.
  • Average radius (ravg) – the midpoint between rmin and rmax. Many protocols use this for calculations involving gradients or when the exact position is not critical.

If you are pelleting cells or debris, use rmax because the pellet forms at the bottom. For density gradient separations, the force varies across the tube, so you may need to calculate g at both extremes. Check your rotor’s manual – it usually lists rmin and rmax in cm or mm.

Common Mistakes and Misconceptions

  • Using diameter instead of radius – the formula needs the radius (half the diameter). If you measure the diameter, divide by 2 first.
  • Mixing units – if you enter the radius in millimeters but the formula expects centimeters, your result will be off by a factor of 10. Use the same unit throughout.
  • Forgetting that RPM is squared – a small increase in RPM causes a large increase in g-force. Going from 3000 to 6000 RPM quadruples the force.
  • Assuming g-force is linear with speed – it is quadratic, as shown in the formula.
  • Using the rotor radius instead of the sample’s radius – in a fixed-angle rotor, the sample may not be at the outer edge; the effective radius depends on the tube position and fill volume.

Practical Applications

This conversion is used in virtually every lab that performs centrifugation:

  • Cell pelleting – typical forces range from 300 ×g for gentle pelleting of mammalian cells to 10,000–20,000 ×g for bacterial cells.
  • Subcellular fractionation – differential centrifugation uses increasing g-forces to separate organelles (e.g., nuclei at 1,000 ×g, mitochondria at 10,000 ×g).
  • DNA/RNA precipitation – often requires 12,000–16,000 ×g for 10–15 minutes.
  • Protein precipitation – 10,000–15,000 ×g is common.
  • Blood processing – serum or plasma separation typically uses 1,000–2,000 ×g for 10–15 minutes.

When a protocol gives a g-force, you can use this calculator to find the RPM needed for your rotor. If the protocol gives RPM, convert to g-force to compare with your instrument’s capabilities.

Safety and Limits of the Formula

Never exceed the maximum speed rating of your rotor. The formula itself is purely mathematical, but real rotors have mechanical limits – exceeding them can cause catastrophic failure. Always check the rotor’s maximum RPM and the manufacturer’s guidelines. Also, the formula assumes a rigid rotor and constant speed; it does not account for acceleration/deceleration time, which can affect separations that are time-sensitive. For most protocols, the effect is negligible, but for delicate gradients, you should consider the actual run time including ramping.

Follow your lab method, the safety data sheet (SDS) and your supervisor when performing any centrifugation. Always balance the rotor properly – an unbalanced rotor can cause vibration, damage the centrifuge, and lead to sample loss or injury.

Frequently Asked Questions

How do I convert g-force to RPM?

Rearrange the formula: RPM = sqrt(RCF / (1.118 × 10⁻⁵ × r)). For example, to get 10,000 ×g with a radius of 10 cm, RPM = sqrt(10000 / (1.118 × 10⁻⁵ × 10)) = sqrt(10000 / 0.0001118) = sqrt(89,445,000) ≈ 9458 RPM. Use this calculator by entering the desired g-force and adjusting the RPM until the output matches.

What is the difference between RCF and g-force?

None – they are the same thing. RCF (relative centrifugal force) is expressed as multiples of Earth’s gravity, so 1 RCF = 1 ×g. The terms are used interchangeably in protocols.

Why does my centrifuge have a max RPM but also a max g-force?

Because the g-force depends on the rotor radius. A rotor with a larger radius will produce a higher g-force at the same RPM. The centrifuge’s maximum g-force is usually specified for the largest rotor that fits, or for the rotor with the largest radius. Always check the rotor-specific limits.

Can I use this calculator for a swinging-bucket rotor?

Yes, but note that the radius changes as the bucket swings out. At rest, the sample is near the top of the tube; during rotation, the bucket swings horizontal, so the sample moves to the bottom. Use the maximum radius (rmax) for the fully swung-out position, which is what most protocols assume.

What if my rotor radius is in millimeters?

Convert to centimeters by dividing by 10. For example, 50 mm = 5 cm. If you prefer to use millimeters directly, use the formula RCF = 1.118 × 10⁻⁶ × r(mm) × RPM². The calculator on this page accepts centimeters only.

Is the constant 1.118 × 10⁻⁵ always the same?

Yes, for the standard definition of g = 9.80665 m/s². Some older references use 1.12 × 10⁻⁵, which gives a slightly different result (about 0.2% difference). The difference is negligible for most lab work, but for precise calculations, use the exact constant.

Related

Formula used
in r | Rotor radius (cm) | cm | 10 | 0.1 | 100
in rpm | Rotational speed | RPM | 3000 | 1 | 100000
out g | Relative centrifugal force (×g) | ×g | 1.118e-5 * r * rpm^2 | 1
out a | Acceleration (m/s²) | m/s² | g * 9.80665 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →