molecalculator

Moles & Molar Mass

Chemical Reaction Rate Equation Explained

Calculator No. 01-10558 · Updated · Formula and assumptions shown below

Reaction rate 0.00100 mol/(L·s)
Rate constant k
0.05 (units vary)
Set in the form below
Concentration of A
0.1 mol/L
Set in the form below
Concentration of B
0.2 mol/L
Set in the form below
Order in A
1
Set in the form below
You enter
Rate constant k ((units vary)), Concentration of A (mol/L), Concentration of B (mol/L), Order in A, Order in B
You get
Reaction rate (mol/(L·s))
Rounding
5 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The chemical reaction rate equation, also called the rate law, relates the reaction speed to the concentrations of reactants, each raised to a power. You enter the rate constant and reactant concentrations, and the calculator returns the reaction rate in mol/(L·s).

Formula

The general rate equation for a reaction aA + bB → products is written as:

rate = k [A]m [B]n

where:

  • rate = reaction rate in mol/(L·s) (or mol L−1 s−1)
  • k = rate constant, units depend on the overall order (e.g., s−1 for first order, L/(mol·s) for second order)
  • [A] and [B] = molar concentrations of reactants A and B in mol/L
  • m and n = reaction orders with respect to A and B (often 0, 1, or 2, but can be fractional or negative)

The overall order of the reaction is m + n. The exponents m and n are not the stoichiometric coefficients from the balanced equation; they must be determined experimentally (or from a proposed mechanism).

Worked Example

Using the default values from the calculator: k = 0.05 (units depend on order), [A] = 0.10 mol/L, [B] = 0.20 mol/L, m = 1, n = 1.

Step 1: Write the rate law: rate = k [A]1 [B]1

Step 2: Substitute the numbers: rate = 0.05 × (0.10)1 × (0.20)1

Step 3: Multiply: 0.05 × 0.10 = 0.005; then 0.005 × 0.20 = 0.001

Step 4: The rate is 0.001 mol/(L·s). The calculator shows 0.00100 with 5 decimal places.

Assumptions

  • The reaction is in a homogeneous phase (gas or solution), not heterogeneous (solid surface).
  • Temperature is constant; k changes with temperature according to the Arrhenius equation.
  • The rate law is a simple power law; some reactions have more complex forms (e.g., with inhibition terms).
  • Concentrations are in mol/L and time in seconds; other units require conversion.

How to Determine the Rate Law Experimentally

You cannot read the orders from the balanced equation. Instead, chemists use the method of initial rates:

  1. Run the reaction with known initial concentrations of each reactant.
  2. Measure the initial rate (the slope of concentration vs. time at t = 0).
  3. Repeat with one reactant concentration changed while holding others constant.
  4. Compare the rates to find the exponent for each reactant.

For example, if doubling [A] doubles the rate while [B] is constant, then m = 1. If doubling [A] quadruples the rate, then m = 2. If changing [A] has no effect, m = 0.

Another method is the integrated rate law: plot concentration vs. time, ln[A] vs. time, or 1/[A] vs. time. The plot that gives a straight line tells you the order (zero, first, or second respectively).

Common Mistakes and Misconceptions

A frequent error is using the stoichiometric coefficients as the exponents. For the reaction 2NO + O2 → 2NO2, the experimentally determined rate law is rate = k[NO]2[O2], which happens to match the coefficients here, but that is coincidence. For many reactions, such as 2N2O5 → 4NO2 + O2, the rate law is first order in N2O5, not second order.

Another mistake is mixing up units. The rate constant k has units that depend on the overall order:

  • Zero order: k has units mol/(L·s)
  • First order: k has units s−1
  • Second order: k has units L/(mol·s)
  • Third order: k has units L2/(mol2·s)

If you use the wrong k units, your calculated rate will be off by orders of magnitude.

How Temperature Affects the Rate Constant

The rate constant k is not truly constant—it changes with temperature. The Arrhenius equation describes this:

k = A e−Ea/(RT)

where A is the pre-exponential factor (same units as k), Ea is the activation energy in J/mol, R is the gas constant (8.314 J/(mol·K)), and T is the absolute temperature in kelvin. A rule of thumb is that the rate roughly doubles for every 10 °C rise, but this is only approximate and depends on Ea.

When reporting a rate, always state the temperature. This calculator assumes a fixed k at a given temperature; if you change temperature, you need a new k.

Reaction Rate vs. Rate Constant

These two terms are often confused. The reaction rate is the actual speed of the reaction at a given moment, with units of concentration per time. The rate constant k is a proportionality factor that is independent of concentration but depends on temperature and the presence of a catalyst.

For a first-order reaction, the rate is directly proportional to [A]. If you double [A], the rate doubles, but k stays the same. For a second-order reaction, doubling [A] quadruples the rate, again with k unchanged. The calculator lets you see this relationship by changing concentrations while keeping k fixed.

Limitations of the Simple Rate Law

The power-law rate equation works for many elementary reactions, but not all. Some reactions have rate laws with denominators, such as enzyme kinetics (Michaelis–Menten) or reactions with inhibitors. For example, the rate of an enzyme-catalyzed reaction is:

rate = Vmax [S] / (Km + [S])

This does not fit the simple form. Also, for reversible reactions, the net rate is the difference between forward and reverse rates. For reactions at equilibrium, the forward rate equals the reverse rate, so the net rate is zero.

Additionally, the rate law assumes the reaction is not diffusion-limited and that the concentrations are uniform. In real systems, mixing and transport can affect observed rates.

Frequently Asked Questions

What is the difference between rate law and rate equation? They are the same thing. Both refer to the mathematical expression that relates the reaction rate to the concentrations of reactants and the rate constant. Some textbooks use “rate law” for the experimental form and “rate equation” for the general form, but in practice they are interchangeable.

Can the order of a reaction be negative? Yes. A negative order means that increasing the concentration of that reactant slows the reaction. This can happen when a reactant binds to a catalyst site and blocks it, or when a product inhibits the reaction. For example, rate = k[A]−1 means doubling [A] halves the rate.

How do I find the units of the rate constant? The units of k are chosen so that the rate has units of mol/(L·s). For overall order n, the units are (mol/L)1−n·s−1. For n = 1, that is s−1; for n = 2, that is L/(mol·s).

Why is the rate law not based on the balanced equation? Because the balanced equation shows the stoichiometry, not the mechanism. Most reactions occur in a series of elementary steps, and the slowest step (the rate-determining step) controls the rate. The exponents in the rate law come from the molecularity of that slow step, which may not match the overall stoichiometry.

What is a pseudo-first-order reaction? If one reactant is in large excess, its concentration barely changes during the reaction, so it can be treated as constant. The rate law then appears first order in the other reactant, even if the true order is second. This is common in hydrolysis reactions where water is the solvent.

Does the rate equation apply to gases? Yes, but for gases you often use partial pressures instead of concentrations. The ideal gas law relates them: concentration = P/(RT). The rate law form is the same, but the rate constant will have different units if you use pressure.

Related

Formula used
in k | Rate constant k | (units vary) | 0.05 | 0
in a | Concentration of A | mol/L | 0.10 | 0
in b | Concentration of B | mol/L | 0.20 | 0
in m | Order in A | - | 1 | 0
in n | Order in B | - | 1 | 0
out rate | Reaction rate | mol/(L·s) | k * a^m * b^n | 5

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →