molecalculator

Moles & Molar Mass

Concentration M Formula: Calculate Molarity

Calculator No. 01-5379 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The concentration formula for molarity is M = n / V: divide the amount of solute in moles by the final solution volume in liters. This calculator instead accepts solute mass, molar mass, and final volume, then reports molarity in mol/L and millimolar concentration in mM.

Formula

Molarity, represented by M or c, is the amount of dissolved substance divided by the total volume of the solution:

M = n / V

  • M is molar concentration in moles per liter (mol/L), also written M.
  • n is the amount of solute in moles (mol).
  • V is the final solution volume in liters (L), not merely the volume of solvent added.

If the amount is given as a mass, first convert it to moles using n = m / MM, where m is solute mass in grams (g) and MM is molar mass in grams per mole (g/mol). If volume is entered in milliliters, convert it to liters by dividing by 1000. Combining these relationships gives the calculator’s formula: M = m / MM / (VmL / 1000). Millimolar concentration is mM = M × 1000.

Worked Example

Using the calculator’s defaults, find the molarity of 2.922 g of a solute with a molar mass of 58.44 g/mol in a final solution volume of 250 mL.

  1. Convert mass to amount: n = 2.922 g / (58.44 g/mol) = 0.050000 mol.
  2. Convert the final volume to liters: 250 mL / 1000 = 0.250 L.
  3. Divide moles by liters: M = 0.050000 mol / 0.250 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200 mM.

The result is 0.2000 M, or 200 mM. The example treats 250 mL as the final solution volume.

Assumptions

  • The mass is the mass of pure solute, and its entered molar mass applies to the substance and chemical form being used.
  • The entered volume is the final volume of the solution after solute is dissolved, not the starting volume of solvent.
  • The calculation reports analytical molarity from the quantities supplied; it does not account for chemical reactions, dissociation, or changes in volume beyond using the stated final volume.

What Molarity Measures

Molarity describes how many moles of a specified solute are present per liter of solution. A 0.20 M solution contains 0.20 mol of that solute per liter of final solution. It is a ratio, so the same amount of solute becomes less concentrated when distributed through a larger final volume.

The capital letter M is commonly used as shorthand for mol/L: 1 M means 1 mol/L. To avoid confusion between the symbol M for molarity and molar mass, equations often use c for concentration and MM for molar mass. The calculator uses those distinct labels in its calculation.

Using the Result and Choosing Units

Use molarity when a chemistry calculation or lab method specifies concentration in mol/L. The result is based on the exact compound represented by the molar-mass input. For example, a salt’s anhydrous form and hydrated form have different molar masses, so the same weighed mass does not contain the same number of moles.

  • mol/L to mM: multiply by 1000. For example, 0.200 M is 200 mM.
  • mM to mol/L: divide by 1000. For example, 75 mM is 0.075 mol/L.
  • Mass from target molarity: rearrange the equations to m = M × V × MM, with volume in liters.
  • Amount from concentration: rearrange to n = M × V, again using liters.

Keep units consistent. Dividing grams by g/mol gives moles; dividing moles by liters gives mol/L. The calculator converts mL to L explicitly. If you perform the calculation by hand, failing to convert milliliters to liters makes the answer wrong by a factor of 1000.

Common Mistakes and Limits

The most common conceptual mistake is using the solvent volume in place of the final solution volume. A solution made by dissolving a solid and then bringing the mixture to a 250 mL final volume has V = 0.250 L. It is not necessarily equivalent to adding the solid to 250 mL of solvent, because dissolving can change the volume.

Another frequent error is using a molar mass for the wrong chemical form. Check the formula, hydration state, and whether the stated mass refers to a pure substance or a mixture. If purity is less than 100%, the actual amount of solute may be lower than the mass-based calculation assumes; this calculator does not apply a purity correction.

Molarity is based on volume, and solution volume can change with temperature. A concentration prepared or measured at one temperature may therefore differ slightly at another. The calculator also does not predict activity, non-ideal behavior, solubility, or the concentration of individual ions after a substance dissociates. It computes the formal molar concentration from mass, molar mass, and final volume.

Related Concentration Measures

Molarity is not the only way to express concentration. Molality is moles of solute per kilogram of solvent; unlike molarity, it uses solvent mass rather than solution volume. Mass concentration may be given in g/L, while percent concentration may refer to mass per mass, volume per volume, or mass per volume. These measures are not interchangeable without the information needed for conversion, such as density and the precise percent convention.

For a dilution of the same solute, the relationship M1V1 = M2V2 follows from conserving the amount of solute, assuming no reaction or loss. Here, the initial and final concentrations and volumes must use compatible units. This dilution equation is different from the mass-based calculator formula, though both rely on the definition of molarity.

Frequently Asked Questions

What is the formula for concentration M?
Molarity is M = n/V, with moles of solute divided by final solution volume in liters. When mass is supplied, use M = m/(MM × V), with mass in grams, molar mass in g/mol, and volume in liters.

Does M mean molarity or molar mass?
In concentration notation, M usually means molarity, measured in mol/L. Molar mass is a different quantity, measured in g/mol, and is often written as MM to distinguish it.

How do I calculate molarity from grams?
Divide the solute mass in grams by its molar mass to get moles. Then divide those moles by the final solution volume in liters.

How do I convert M to mM?
Multiply mol/L by 1000. Thus, 0.025 M equals 25 mM; divide by 1000 to convert in the opposite direction.

Should I use the volume of solvent or solution?
Use the final volume of the complete solution. Solvent volume alone is not the denominator in the molarity definition.

For any bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →