molecalculator

Moles & Molar Mass

Mass/Volume Concentration Calculator and Formula

Calculator No. 01-5381 · Updated · Formula and assumptions shown below

Mass/volume concentration 11.6880 g/L
Molarity
0.2000 mol/L
= (Mass of solute ÷ Molar mass) ÷ (Final solution volume ÷ 1000)
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Mass/volume concentration (g/L), Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Mass/volume concentration is the mass of a dissolved substance divided by the final volume of the solution, commonly written in g/L or mg/mL. Enter the solute mass, its molar mass, and the final solution volume below to calculate the mass/volume concentration in g/L and the equivalent molarity and millimolar concentration.

Formula

Mass/volume concentration is solute mass divided by final solution volume:

cm/v = m / V

  • cm/v is mass/volume concentration in g/L.
  • m is the mass of solute in grams (g).
  • V is the final volume of solution in liters (L).

The calculator accepts volume in milliliters, so it converts mL to L by dividing by 1000: V = v / 1000. It also calculates molarity using c = (m / M) / V, where M is molar mass in g/mol and c is in mol/L. Millimolar concentration is molarity multiplied by 1000: cmM = c × 1000. These calculations assume the entered mass is the solute mass and the entered volume is the final solution volume.

Worked Example

Using the calculator’s defaults, the solute mass is 2.922 g, molar mass is 58.44 g/mol, and final volume is 250 mL.

  1. Convert final volume to liters: 250 mL / 1000 = 0.25 L.
  2. Calculate mass/volume concentration: 2.922 g / 0.25 L = 11.688 g/L.
  3. Calculate moles of solute: 2.922 g / 58.44 g/mol = 0.05 mol.
  4. Calculate molarity: 0.05 mol / 0.25 L = 0.2 mol/L.
  5. Convert to millimolar: 0.2 mol/L × 1000 = 200 mM.

The displayed results are 11.6880 g/L, 0.2000 mol/L, and 200.00 mM, respectively.

Assumptions

  • The volume entered is the solution’s final volume, not the amount of solvent used.
  • The solute mass and molar mass refer to the same substance and chemical form.
  • The solution is treated as a mixture for concentration arithmetic; no density or volume-change correction is applied.

What Mass/Volume Concentration Means

Concentration describes how much solute is present relative to a specified amount of solution. In mass/volume concentration, the numerator is a mass and the denominator is a volume. For example, 11.688 g/L means that each liter of solution contains 11.688 g of the specified solute, assuming the mixture is uniform.

Units communicate which kind of concentration is meant. A value in g/L is mass per volume; mol/L is amount of substance per volume; and percent mass/volume, often written % (m/v) or % w/v, conventionally means grams of solute per 100 mL of final solution. These formats can be converted when their definitions and units are clear. For example, 1 g/100 mL equals 10 g/L.

Mass/volume concentration is not the same as mass fraction, which compares solute mass with total solution mass, or volume fraction, which compares component volumes. Those quantities have different denominators and cannot be substituted without additional information.

When to Use Each Result

Use g/L when the question concerns a mass of solute per solution volume, such as comparing solution compositions or checking a stated mass concentration. Use molarity when chemical calculations require moles per liter, including stoichiometric comparisons in solution. The conversion needs the compound’s molar mass: different substances with the same g/L can have different molarities because their molecules have different masses.

For the example, 11.688 g/L corresponds to 0.2000 mol/L only because the entered molar mass is 58.44 g/mol. The output in mM is simply molarity expressed in thousandths of a mole per liter: 0.2000 mol/L is 200.00 mmol/L, or 200.00 mM.

If a recipe or specification uses g/100 mL, multiply that numerical value by 10 to express it in g/L. If it uses mg/mL, the numerical value is the same as g/L: 1 mg/mL equals 1 g/L, because both numerator and denominator scale by 1000.

Inputs, Units, and Common Mistakes

  • Enter the final solution volume. If a solute is added to solvent, the final volume may not equal the starting solvent volume. Use the volume after the solution has been made up to its intended mark or otherwise measured.
  • Keep units consistent. This calculator expects mass in grams, molar mass in g/mol, and volume in milliliters. Convert other units before entering them: 1 mg = 0.001 g, and 1 L = 1000 mL.
  • Choose the right molar mass. Molar mass depends on the chemical formula and, where relevant, the specified form, such as a hydrate or salt. A wrong value changes molarity even when mass/volume concentration is unaffected.
  • Do not confuse a concentration with a quantity. A concentration such as g/L does not by itself say how many grams are present in a particular sample. Multiply by that sample’s volume in liters to obtain its solute mass.
  • Retain sensible precision. A calculator can display several decimal places, but the result cannot be more reliable than the measurements and stated molar mass. Round only after completing the calculation.

A common misconception is that adding a certain volume of solvent produces that same final solution volume. Dissolving a solid can change volume, so the denominator in the formula must be the final volume specified for the solution, not automatically the solvent volume.

Scope and Practical Limits

This calculation gives a concentration from supplied values; it does not determine whether a substance dissolves, whether a mixture is stable, or whether the measured volume is accurate. It also does not account for purity, impurities, reaction during mixing, temperature-dependent volume changes, or uncertainty in measuring mass and volume. For an actual laboratory calculation, use the appropriate chemical form and measured final volume. Follow your lab method, the safety data sheet (SDS), and your supervisor.

Mass/volume concentration is a bookkeeping relationship, not a preparation procedure. The formula is useful for checking units and converting between mass concentration and molarity, but experimental conditions and the intended analytical method determine whether those values adequately describe a real sample.

Frequently Asked Questions

How do you calculate mass/volume concentration?
Divide the solute mass by the final solution volume, using compatible units. For g/L, divide grams by liters; if volume is in mL, first divide it by 1000 to convert it to liters.

Is mass/volume concentration the same as molarity?
No. Mass/volume concentration uses mass per volume, such as g/L. Molarity uses moles per volume, such as mol/L. Convert between them using the solute’s molar mass.

What does 1% mass/volume mean?
By the usual % (m/v) convention, 1% means 1 g of solute per 100 mL of final solution. That is equivalent to 10 g/L.

Should I use solvent volume or final solution volume?
Use final solution volume. The amount of solvent initially measured may differ from the total volume after the solute dissolves.

How do I convert mg/mL to g/L?
The numerical value is unchanged: 1 mg/mL equals 1 g/L. For example, 4 mg/mL is 4 g/L.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Mass/volume concentration | g/L | m / (v / 1000) | 4
out mol | Molarity | mol/L | (m / mm) / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | mol * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →