Convert absorbance to concentration by using a calibration curve or the Beer–Lambert law, provided you know the substance’s response at the measurement wavelength. Enter absorbance, molar absorptivity, and path length below to calculate concentration in mol/L; the calculator also reports millimolar concentration.
Formula
For a homogeneous, sufficiently dilute absorbing solution, the Beer–Lambert law is A = εlc. Rearranged to solve for concentration: c = A / (εl).
- A is absorbance, dimensionless and usually reported without a unit.
- ε is molar absorptivity, in L/(mol·cm), for the particular substance, wavelength, solvent, and conditions.
- l is the optical path length through the sample, in cm.
- c is concentration, in mol/L. To convert mol/L to mmol/L (mM), multiply by 1000.
The calculator assumes the entered absorbance is the sample’s corrected absorbance, such as sample absorbance minus an appropriate blank, and that the entered ε applies to the exact measurement conditions. Its default ε is an illustrative conventional value, not a universal property: consult a reliable value for your analyte or determine the response with standards.
Worked Example
Using the calculator’s defaults—absorbance 0.500, molar absorptivity 10,000 L/(mol·cm), and path length 1 cm:
- Apply the Beer–Lambert rearrangement: c = A / (εl).
- Substitute the values: c = 0.500 / (10,000 × 1) = 0.000050000 mol/L.
- Convert to millimolar: 0.000050000 mol/L × 1000 = 0.050 mM.
The calculator therefore returns 0.000050 mol/L (to six decimal places) and 0.050 mM. The molar result is rounded for display; its unrounded value is 5.0000 × 10−5 mol/L.
Assumptions
- The sample is sufficiently dilute and homogeneous for absorbance to be proportional to concentration over the measured range.
- The analyte’s molar absorptivity is known and valid at the selected wavelength and under the sample’s solvent and chemical conditions.
- The path length is the distance light travels through the sample, not necessarily the container’s external width.
- The absorbance has been blank-corrected, and the instrument is functioning within its usable measurement range.
When to Use a Calibration Curve
The direct calculation is convenient when a dependable molar absorptivity is available and Beer–Lambert behavior is suitable. In many practical analyses, however, a calibration curve is more reliable. Measure a blank and several standards with known concentrations under the same conditions as the unknown, then plot corrected absorbance against standard concentration. If the response is linear, fit a line, commonly written A = mc + b, where m is the slope and b is the intercept. For the unknown, calculate c = (A − b)/m.
A calibration curve empirically accounts for the instrument, cuvette, wavelength, and method used. It can also reveal a nonzero baseline or departures from linearity. The standards should cover the unknown’s response; do not assume a line remains valid well beyond the measured range. If the unknown’s absorbance falls outside the standards, dilute it by a known factor or prepare a more appropriate calibration range, then account for the dilution in the final concentration.
What Absorbance Tells You
Absorbance describes how much light a sample removes from a beam at a specified wavelength. It is defined as A = log10(I0/I), where I0 is incident light intensity and I is transmitted intensity. Since it is a logarithmic ratio, absorbance is not itself a concentration and has no concentration unit. A value of 1 means the transmitted intensity is one tenth of the incident intensity, after the measurement’s reference and blank conventions are applied.
Concentration follows only when absorbance is connected to the analyte through an appropriate response factor or calibration. A colored sample may contain multiple absorbing substances, and scattering particles can also reduce transmitted light. In either case, treating all observed absorbance as if it came from one pure analyte can give a misleading result.
Common Errors and Limits
- Using the wrong ε: Molar absorptivity varies with wavelength and can depend on solvent, pH, chemical form, and temperature. A literature value measured under different conditions may not apply.
- Mixing units: This calculator expects ε in L/(mol·cm) and path length in cm. For example, if a path length is supplied in mm, convert it to cm by dividing by 10 before entering it. Do not enter a path length in mm as if it were cm.
- Forgetting dilution: If a sample was diluted before measurement, the calculated concentration is the concentration in the measured solution. Multiply by the total dilution factor to recover the original sample concentration.
- Skipping a suitable blank: Solvent, reagents, and cuvette effects can contribute to the reading. Use a blank that matches the sample matrix as closely as the method requires.
- Trusting extreme readings: Very low signals are vulnerable to baseline noise; high absorbance can exceed an instrument’s reliable range or stray-light limits. Check the method’s validated range rather than assuming the equation corrects these problems.
- Ignoring chemistry or scattering: Changes in analyte form, mixtures, turbidity, or suspended particles can break the simple proportional relationship.
Beer–Lambert calculations are study and lab-planning arithmetic, not a substitute for a validated analytical method. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
Can I convert absorbance to concentration without molar absorptivity?
Yes, if you have a calibration curve made from standards of known concentration. Without ε or a suitable calibration, absorbance alone does not determine a unique concentration.
What if the cuvette path length is not 1 cm?
Use the actual optical path length in cm. At the same absorbance and ε, a longer path length corresponds to a lower calculated concentration in the Beer–Lambert equation.
Do I need to subtract the blank?
Usually, use absorbance corrected with a suitable blank or the measurement procedure’s reference correction. Whether blank subtraction is already applied depends on the instrument and method, so avoid subtracting it twice.
How do I account for a diluted sample?
First calculate the concentration in the diluted solution. Multiply that result by the dilution factor—the original volume divided by the final diluted volume—to estimate the concentration before dilution.
Does absorbance have units?
No. It is a logarithmic ratio of light intensities, so it is dimensionless. Concentration units come from the calculation, ε, path length, and any required unit conversions.
Related
Formula used
in a | Absorbance | - | 0.500 | 0 in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0 in l | Path length | cm | 1 | 0 out c | Concentration | mol/L | a / (eps * l) | 6 out cm | Concentration | mM | c * 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Cell Culture Doubling Time Equation and Calculator24.00 h
- Cell Culture Doubling Time Calculator and Formula24.00 h
- Cell Culture Seeding Density Calculator and Formula4,000.00 cells/cm^2
- CFU From Dilution: Calculate Colony-Forming Units10,000,000 CFU/mL
- Cell Culture Doubling Time Calculator and Formula24.00 h
- Zero Order Release Kinetics Calculator and Explanation5.000 mg/h