molecalculator

Moles & Molar Mass

Converting Molarity to Molality: Formula and Calculator

Calculator No. 01-2328 · Updated · Formula and assumptions shown below

Molality 1.009 mol/kg
Solvent mass per liter of solution
0.000992 kg/L
= (Solution density − Molarity × Solute molar mass ÷ 1000) ÷ 1000
Molarity
1 mol/L
Set in the form below
Solution density
1.05 g/mL
Set in the form below
You enter
Molarity (mol/L), Solution density (g/mL), Solute molar mass (g/mol)
You get
Molality (mol/kg), Solvent mass per liter of solution (kg/L)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts molarity to molality using the solution’s density and the solute’s molar mass. Enter molarity in mol/L, density in g/mL, and molar mass in g/mol; the result is molality in mol/kg of solvent.

Formula

Molarity describes moles of solute per liter of solution, while molality describes moles of solute per kilogram of solvent. To convert between them, account for the mass of one liter of solution and subtract the mass of solute in that liter:

m = C / [ρ − (C × M) / 1000]

  • m is molality in mol/kg.
  • C is molarity in mol/L.
  • ρ is solution density in g/mL. One liter of solution has a mass of 1000ρ grams.
  • M is the solute’s molar mass in g/mol. At molarity C, one liter contains C moles, with a solute mass of CM grams.

The denominator is the mass of solvent, in kilograms, in one liter of solution: (1000ρ − CM) / 1000. The calculator’s first result is molality. Its second result, (ρ − CM/1000)/1000, is the solvent mass in kg per liter of solution and provides a useful check. The factor 1000 converts milliliters to liters and grams to kilograms where needed.

Worked Example

Using the calculator’s default values, convert a 1 mol/L solution with density 1.05 g/mL and a solute molar mass of 58.44 g/mol:

  1. Mass of one liter of solution: 1.05 g/mL × 1000 mL/L = 1050 g.
  2. Solute mass in that liter: 1 mol/L × 58.44 g/mol = 58.44 g.
  3. Solvent mass: 1050 g − 58.44 g = 991.56 g = 0.99156 kg.
  4. Molality: 1 mol ÷ 0.99156 kg = 1.0085 mol/kg, which rounds to 1.009 mol/kg.

The solvent-mass output is 0.992 kg/L when rounded to three decimal places. The unrounded value, 0.99156 kg/L, is used in the molality calculation.

Assumptions

  • The density applies to the complete solution at the same temperature and pressure relevant to the stated molarity.
  • The molar mass corresponds to the solute formula and chemical form used to define the concentration.
  • The solution contains a physically meaningful positive mass of solvent. The denominator must be greater than zero.
  • Molarity is based on final solution volume, not the volume of solvent added.

When and Why to Convert

Molarity is convenient for preparing and describing solutions by volume. It is temperature-dependent because a liquid’s volume can expand or contract as temperature changes. Molality is based on solvent mass, which ordinarily does not change with temperature, so it is useful in calculations involving boiling-point elevation, freezing-point depression, and other colligative properties.

Conversion requires density because molarity alone does not tell you how much a liter of solution weighs. It also requires molar mass because the solute’s mass must be removed from the total solution mass to find the solvent mass. Without density and molar mass, there is not enough information to determine molality from molarity alone.

Use density for the actual solution composition and conditions whenever possible. A density listed for pure water, a different concentration, or a different temperature may not be suitable. For dilute aqueous solutions, density may be close to 1 g/mL, but treating it as exactly 1 can introduce error, especially for concentrated solutions or precision work.

How to Use and Check the Result

  • Enter molarity in mol/L, not mmol/L or mM. For example, 25 mM is 0.025 mol/L.
  • Enter solution density in g/mL and molar mass in g/mol. Check that the molar mass matches the compound and its stated chemical form.
  • Confirm that ρ − CM/1000 is positive. This quantity represents solvent mass per milliliter of solution; a zero or negative value is not physically valid for this calculation.
  • Read molality as moles of solute per kilogram of solvent, not per kilogram of solution.

Retain extra digits through intermediate calculations and round only the final answer to a precision justified by the inputs. A calculator’s displayed result cannot be more reliable than uncertain density or concentration data. If a density is reported with only a few significant figures, reporting many decimal places in molality implies unjustified precision.

Molarity and Molality Compared

The difference is what appears in the denominator: molarity uses liters of the entire solution; molality uses kilograms of solvent alone. They are not interchangeable units, and a value in mol/L does not become a value in mol/kg merely by changing the unit label. The solute contributes to solution mass, while solvent volume is not generally equal to final solution volume.

For dilute water-based solutions, the two numerical values can be similar because the density is often near 1 g/mL and the solute mass may be small relative to the water mass. Similar does not mean identical. At higher concentrations, or when the solvent has a substantially different density, the difference can be significant. In nonaqueous mixtures, use the density of the actual solution rather than relying on water-based approximations.

Common Errors and Limits

  • Using solvent volume instead of final solution volume: Molarity is defined using the final volume after solute and solvent are combined.
  • Subtracting the wrong mass: Subtract the solute mass, CM, from the total mass of one liter of solution. Do not subtract the mass of one liter of solvent.
  • Mixing units: The formula as written expects C in mol/L, ρ in g/mL, and M in g/mol. Convert inputs before using it if they are supplied in other units.
  • Using an unsuitable density: Density can vary with composition and temperature. A reference value for pure solvent is not automatically the solution density.
  • Ignoring chemical form: Hydrates, salts, and other specified forms have different molar masses. Use the value for the species whose moles define the stated molarity.

The calculation converts stated concentrations; it does not correct for non-ideal solution behavior, chemical reaction, dissociation, or uncertainty in measured values. If molarity itself was measured or calculated at a particular temperature, keep that context with the result. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

Can I convert molarity to molality without density?
No. Molarity and molar mass give the mass of solute in a chosen solution volume, but density is needed to find the total mass of that solution and therefore the remaining solvent mass.

Is molarity the same as molality?
No. Molarity is moles of solute per liter of solution; molality is moles of solute per kilogram of solvent. Their numerical values may be close in some dilute solutions, but they are different quantities.

Why does temperature matter for this conversion?
Molarity depends on solution volume, which can change with temperature. Density also depends on temperature. Use density consistent with the solution’s conditions and the molarity’s temperature basis.

What if I know molality and want molarity?
You need density and molar mass as well. For molality m, one kilogram of solvent contains m moles of solute; the solute mass is mM grams. Combine that with the solvent mass to get solution mass, use density to obtain solution volume, then calculate moles per liter.

Does the formula work for any solute?
It works as a mass-balance conversion when the inputs describe the same solution and the molar mass matches the solute definition. It does not by itself account for reactions, changing chemical species, or measurement uncertainty.

Related

Formula used
in c | Molarity | mol/L | 1 | 0
in d | Solution density | g/mL | 1.05 | 0.000001
in mm | Solute molar mass | g/mol | 58.44 | 0.000001
out b | Molality | mol/kg | c / (d - c * mm / 1000) | 3
out n | Solvent mass per liter of solution | kg/L | (d - c * mm / 1000) / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →