molecalculator

Moles & Molar Mass

Copper Sulfate Hydrate Molar Mass Explained

Calculator No. 01-7386 · Updated · Formula and assumptions shown below

Molarity 0.0468 mol/L
Concentration in millimolar
46.81 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
249.69 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The molar mass of copper(II) sulfate pentahydrate (CuSO4·5H2O) is 249.69 g/mol. This value includes the mass of five water molecules bound in the crystal structure; the anhydrous form (CuSO4) has a molar mass of 159.61 g/mol. This page provides a calculator to determine the molar mass from a formula you enter, plus a detailed breakdown of how the value is calculated and why the hydrate form matters in the lab.

Formula

The molar mass of a hydrate is the sum of the atomic masses of all atoms in the chemical formula, including the water molecules. For copper(II) sulfate pentahydrate, the formula is:

M(CuSO4·5H2O) = M(Cu) + M(S) + 4·M(O) + 5·[2·M(H) + M(O)]

Using IUPAC standard atomic weights (rounded to two decimals):

  • Cu: 63.55 g/mol
  • S: 32.06 g/mol
  • O: 16.00 g/mol (4 in sulfate + 5 in water = 9 total)
  • H: 1.008 g/mol (10 in water)

So: 63.55 + 32.06 + 9×16.00 + 10×1.008 = 63.55 + 32.06 + 144.00 + 10.08 = 249.69 g/mol.

Worked Example

Using the calculator defaults, suppose you weigh out 2.922 g of CuSO4·5H2O and dissolve it in water to make 250 mL of solution. What is the molarity?

  1. Convert volume to liters: 250 mL = 0.250 L.
  2. Calculate moles of solute: moles = mass / molar mass = 2.922 g / 249.69 g/mol = 0.01170 mol.
  3. Molarity = moles / volume = 0.01170 mol / 0.250 L = 0.04680 mol/L (or 46.80 mM).

The calculator gives the same result: 0.0468 mol/L (rounded to 4 decimals).

Assumptions

  • The compound is pure copper(II) sulfate pentahydrate with the exact formula CuSO4·5H2O.
  • Atomic weights are the IUPAC abridged values; commercial reagent purity may vary slightly.
  • When preparing a solution, the final volume is used (not the volume of solvent added).
  • The solution is at room temperature; molarity is temperature-dependent (volume changes with temperature).

Why the Hydrate Form Matters

Copper sulfate is commonly sold as the pentahydrate because it is stable and easy to crystallize. The water molecules are part of the crystal lattice, not just surface moisture. If you weigh the hydrate but assume the anhydrous mass, your molarity will be off by about 56% (because 249.69 vs 159.61). For precise lab work, always check the label: “CuSO4·5H2O” or “pentahydrate” means you must use 249.69 g/mol; “anhydrous” or “dried” means 159.61 g/mol.

When you dissolve the hydrate, the water molecules become part of the solvent, so the effective solute is just CuSO4. The molarity calculation uses the hydrate’s molar mass to find moles of CuSO4 (since one mole of hydrate gives one mole of CuSO4).

Common Mistakes

  • Forgetting the water: Using 159.61 instead of 249.69 leads to a concentration that is too high.
  • Miscounting oxygen atoms: There are 4 in the sulfate plus 5 in water = 9, not 4.
  • Unit mix-ups: Volume in mL must be converted to L (divide by 1000) before calculating molarity.
  • Rounding too early: Round atomic weights only at the end; using 64 for Cu gives 250.1, a small but avoidable error.

How to Use the Calculator

Enter the mass of your copper sulfate hydrate sample (in grams), the molar mass (adjust if you have a different hydrate, e.g., trihydrate or anhydrous), and the final solution volume in mL. The calculator returns molarity in mol/L and millimolar. For example, to make a 0.1 M solution, you would need 24.969 g of pentahydrate per liter of final solution.

The calculator is for study and lab planning only. Always follow your lab method, the safety data sheet (SDS) and your supervisor.

Safety and Handling

Copper sulfate is an irritant to eyes and skin, and harmful if swallowed. Wear gloves and goggles when handling the powder. Avoid inhaling dust. Store in a tightly closed container in a dry place; the hydrate can lose water if heated above 150 °C, turning into the anhydrous form. Dispose of solutions according to local regulations—copper is a heavy metal and should not go down the drain in large amounts.

Frequently Asked Questions

What is the molar mass of anhydrous copper sulfate?

Anhydrous CuSO4 has a molar mass of 159.61 g/mol (63.55 + 32.06 + 4×16.00). It is a white powder, while the pentahydrate is blue.

How do I convert from grams of hydrate to moles of copper sulfate?

Divide the mass of the hydrate by 249.69 g/mol. The result is the number of moles of CuSO4 because each formula unit of the hydrate contains one CuSO4 unit.

Why is the hydrate blue but the anhydrous form white?

The blue color comes from the water molecules coordinated to the copper ion in the crystal. When water is removed, the coordination changes and the color disappears.

Can I use the molar mass of the hydrate to prepare a solution of known copper ion concentration?

Yes. Since each mole of hydrate gives one mole of Cu2+, the molarity of copper ions equals the molarity of the hydrate you dissolved (assuming complete dissociation).

Does the molar mass change if the hydrate is partially dehydrated?

Yes. If some water is lost (e.g., by heating or exposure to dry air), the effective molar mass will be between 159.61 and 249.69. For accurate work, use a freshly opened bottle and store it tightly closed.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 249.69 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →