Copper sulfate molecular mass is 159.61 g/mol for the anhydrous form (CuSO4) and 249.69 g/mol for the common pentahydrate (CuSO4·5H2O). You enter the chemical formula or hydrate form, and the calculator below returns the molar mass in grams per mole, which you then use to convert between mass and moles in solutions or reactions.
Formula
The molar mass (M) is the sum of the atomic weights of every atom in the formula unit, multiplied by the number of times that atom appears. For copper sulfate pentahydrate:
M(CuSO4·5H2O) = M(Cu) + M(S) + 4×M(O) + 5×[2×M(H) + M(O)]
Using IUPAC standard atomic weights (Cu 63.546, S 32.06, O 15.999, H 1.008):
- Cu: 63.546 g/mol
- S: 32.06 g/mol
- O (in sulfate): 4 × 15.999 = 63.996 g/mol
- 5 H2O: 5 × (2×1.008 + 15.999) = 5 × 18.015 = 90.075 g/mol
Total = 63.546 + 32.06 + 63.996 + 90.075 = 249.677 g/mol ≈ 249.68 g/mol. For the anhydrous form, omit the water part: 63.546 + 32.06 + 63.996 = 159.602 ≈ 159.60 g/mol.
Worked Example
Suppose you need 250 mL of a 0.0468 mol/L solution of copper sulfate pentahydrate. Using the default mass of 2.922 g:
- Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
- Calculate moles of hydrate: 2.922 g ÷ 249.69 g/mol = 0.011703 mol
- Divide by volume: 0.011703 mol ÷ 0.250 L = 0.04681 mol/L ≈ 0.0468 M
- Convert to millimolar: 0.04681 × 1000 = 46.81 mM
The calculator returns 0.0468 mol/L and 46.81 mM, matching the steps.
Assumptions
- The hydrate is the pure pentahydrate (CuSO4·5H2O) with no surface moisture or efflorescence.
- Atomic weights are IUPAC standard values; real reagent purity may vary slightly.
- The final solution volume is exactly the volume you measure after dissolving, not the volume of solvent added.
- Dissolution is complete and no water is lost during preparation.
When to Use This Calculator
You use molar mass whenever you need to convert between grams and moles. This calculator is set up for the most common lab task: preparing a solution of copper sulfate pentahydrate at a target molarity. You enter the mass you weighed out, the molar mass (default is the hydrate), and the final volume; the calculator gives the molarity. If you want to prepare a specific concentration, you can adjust the mass and volume until the molarity matches your target.
Copper sulfate appears in many contexts: as a fungicide in agriculture, an algicide in pools, a reagent in analytical chemistry, and a common example in general chemistry textbooks for hydrate calculations. In every case, the molar mass is the bridge between the solid you measure and the moles that react or dissolve.
Common Mistakes and Misconceptions
- Forgetting the water of hydration: The blue crystals are almost always the pentahydrate. Using 159.61 instead of 249.69 will give a molarity about 56% too high.
- Adding solvent to a volume: You must dissolve the solid in less than the final volume, then add water up to the mark. Adding 250 mL of water to 2.922 g gives a slightly lower concentration because the final volume is larger.
- Confusing mass and moles: Molarity is moles per liter, not grams per liter. Always divide by the molar mass first.
- Rounding too early: If you round the molar mass to 250 g/mol, your result changes by about 0.1%. That is usually fine, but for precise work keep at least four significant figures.
- Assuming anhydrous when the label says hydrate: Always check the reagent bottle. If it says CuSO4 (anhydrous, white powder), use 159.61; if it says pentahydrate (blue crystals), use 249.69.
Anhydrous vs. Hydrate: Why the Difference Matters
The pentahydrate contains five water molecules trapped in the crystal lattice. When you heat it above about 150 °C, it loses water and becomes the white anhydrous powder. The molar mass difference is significant: 159.61 vs. 249.69 g/mol. In a recipe that calls for “copper sulfate,” you must know which form is meant. Many commercial products list the hydrate because it is the stable, common form. If you use the wrong molar mass, your concentration will be off by a factor of 249.69/159.61 = 1.564, which is a 56% error.
For stoichiometry in reactions (e.g., preparing copper hydroxide or copper complexes), you should always write the formula with the water of hydration explicitly, then use the corresponding molar mass.
Safety and Handling
Copper sulfate is a skin and eye irritant and is harmful if swallowed. It can cause severe eye damage. Wear gloves and goggles when handling the powder or solution. Avoid inhaling dust. Do not dispose of copper sulfate solutions down the drain without checking local regulations—copper is a heavy metal and can harm aquatic life. In case of contact, rinse skin with water and eyes with plenty of water for at least 15 minutes and seek medical advice. Always follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What is the molecular mass of copper sulfate pentahydrate?
It is 249.68 g/mol. This includes the five water molecules: 63.546 (Cu) + 32.06 (S) + 63.996 (four O) + 90.075 (five H2O) = 249.677 g/mol.
What is the difference between molecular mass and molar mass?
Molecular mass is the mass of one molecule in atomic mass units (u), numerically equal to the molar mass in grams per mole. Molar mass is the mass of one mole of substance. For copper sulfate, both are 159.61 (anhydrous) or 249.68 (hydrate) depending on the unit.
How do I convert grams of copper sulfate to moles?
Divide the mass by the molar mass. For example, 10.0 g of CuSO4·5H2O ÷ 249.68 g/mol = 0.04005 mol.
Why is the anhydrous form sometimes used instead of the hydrate?
Anhydrous copper sulfate is used when you need exact stoichiometry without water interference, or when the hydrate would introduce extra water mass. It is also used as a desiccant to absorb moisture. However, it is less common in general lab work because it is hygroscopic—it will absorb water from air and slowly become the hydrate again.
Does copper sulfate have a molecular formula or an empirical formula?
It is an ionic compound, so strictly it has a formula unit, not a molecule. The formula CuSO4 represents the ratio of ions. The term “molecular mass” is often used loosely for ionic compounds; the correct term is “formula mass” or “molar mass.”
How many atoms are in one formula unit of CuSO4·5H2O?
One formula unit contains 1 Cu, 1 S, 4 O (sulfate), and 5 H2O (which gives 10 H and 5 O). Total atoms = 1+1+4+10+5 = 21 atoms. In one mole, there are 6.022 × 1023 formula units, so about 1.26 × 1025 atoms.
Related
Formula used
in m | Mass of CuSO4·5H2O | g | 2.922 | 0 in mm | Molar mass (hydrate) | g/mol | 249.69 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Volume Calculator in Chemistry: How to Use It0.2000 mol/L
- Volume Calculator in mm: Convert & Calculate100,000 mm³
- Volume Calculator Feet and Inches: How to Use It3.12 ft³
- Volume Calculator: Convert ft to Yards1.00 yd³
- Surfboard Volume Calculator JS: How It Works32.4 L
- Volume Calculator cm to Litres: How to Convert2.500 L