The molar mass of anhydrous copper sulphate (CuSO4) is 159.61 g/mol. For the common pentahydrate form (CuSO4·5H2O), the molar mass is 249.69 g/mol. This article explains how these values are derived, why the hydrated form is heavier, and how to use molar mass in real laboratory calculations.
Formula
The molar mass (M) of a compound is the sum of the atomic masses of each element multiplied by its subscript in the chemical formula. For copper sulphate:
M(CuSO4) = Ar(Cu) + Ar(S) + 4 × Ar(O)
Where Ar is the relative atomic mass (IUPAC standard): Cu = 63.546, S = 32.06, O = 15.999 g/mol.
For the pentahydrate, add the mass of five water molecules: M(CuSO4·5H2O) = M(CuSO4) + 5 × M(H2O), with M(H2O) = 18.015 g/mol.
Worked Example
Calculate the mass of anhydrous copper sulphate needed to prepare 250 mL of a 0.200 mol/L solution.
- Convert volume to litres: 250 mL ÷ 1000 = 0.250 L
- Moles required = molarity × volume = 0.200 mol/L × 0.250 L = 0.0500 mol
- Mass = moles × molar mass = 0.0500 mol × 159.61 g/mol = 7.9805 g
For the pentahydrate, use 249.69 g/mol: 0.0500 mol × 249.69 g/mol = 12.4845 g. The calculator above gives the same result when you enter the mass and molar mass.
Assumptions
- The atomic weights used are the IUPAC standard values.
- The anhydrous form is pure and dry (no absorbed water).
- The pentahydrate has exactly five water molecules per formula unit.
- Solution volume is the final volume, not the volume of solvent added.
Why Two Molar Masses?
Copper sulphate commonly appears as the blue pentahydrate crystal, which contains five water molecules trapped in the crystal lattice. When heated, it loses this water and becomes the white anhydrous powder. The two forms have different molar masses because the water contributes to the mass of the hydrate. Always check the label: if it says “CuSO4” use 159.61; if it says “CuSO4·5H2O” use 249.69. Using the wrong value changes the concentration by about 56%.
How to Use Molar Mass in Solution Prep
To make a solution of known molarity, you need to weigh the correct mass of solute. The steps are:
- Decide the final volume (in litres) and desired concentration (mol/L).
- Calculate moles: moles = concentration × volume.
- Multiply moles by the molar mass to get the mass in grams.
- Dissolve that mass in a small amount of solvent, then top up to the final volume.
For example, to prepare 500 mL of 0.100 mol/L CuSO4 (anhydrous): moles = 0.100 × 0.500 = 0.0500 mol; mass = 0.0500 × 159.61 = 7.98 g. For the pentahydrate, use 12.48 g.
Common Mistakes and Misconceptions
- Confusing hydrate and anhydrous: The most common error is using the wrong molar mass. Always verify the formula on the container.
- Ignoring water of hydration: If you weigh the pentahydrate but use the anhydrous molar mass, your solution will be too dilute.
- Volume error: The molarity formula uses final volume, not the volume of solvent added. Always top up to the mark in a volumetric flask.
- Rounding too early: Round only at the end; intermediate rounding can shift the final concentration.
Safety and Handling
Copper sulphate is an irritant to skin and eyes. Wear gloves and safety goggles, and avoid inhaling dust. It is toxic to aquatic life, so do not pour it down the drain. Follow your lab method, the safety data sheet (SDS) and your supervisor. For disposal, consult local regulations.
Frequently Asked Questions
What is the molar mass of CuSO4?
Anhydrous copper sulphate has a molar mass of 159.61 g/mol. This is the sum of copper (63.546), sulfur (32.06), and four oxygens (4 × 15.999 = 63.996).
What is the molar mass of CuSO4·5H2O?
The pentahydrate has a molar mass of 249.69 g/mol. It includes five water molecules (5 × 18.015 = 90.075 g/mol) added to the anhydrous mass.
Which form should I use for making a 1 M solution?
It depends on what you have in the lab. If you have the blue crystals, use 249.69 g/mol and weigh 249.69 g per litre. If you have the white anhydrous powder, use 159.61 g/mol and weigh 159.61 g per litre.
Why does the pentahydrate weigh more?
Because it contains water molecules that are chemically bound in the crystal. These water molecules add mass without changing the copper sulphate content.
How do I convert between moles and grams of copper sulphate?
Use the formula: mass (g) = moles × molar mass (g/mol). For example, 0.5 mol of anhydrous CuSO4 weighs 0.5 × 159.61 = 79.805 g.
Does the molar mass change with temperature?
No. Molar mass is a fixed property of the substance. However, the hydrate can lose water if heated, so the effective molar mass of a sample may change if it is not stored properly.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Volume Calculator in Chemistry: How to Use It0.2000 mol/L
- Volume Calculator in mm: Convert & Calculate100,000 mm³
- Volume Calculator Feet and Inches: How to Use It3.12 ft³
- Volume Calculator: Convert ft to Yards1.00 yd³
- Surfboard Volume Calculator JS: How It Works32.4 L
- Volume Calculator cm to Litres: How to Convert2.500 L