molecalculator

Moles & Molar Mass

Cubic Meters per Second to Litres per Second

Calculator No. 01-6400 · Updated · Formula and assumptions shown below

Flow rate 1,000.000 L/s
Flow rate
3,600.000 m³/h
= Flow rate × 3600
Flow rate
60,000.000 L/min
= Flow rate × 60000
Flow rate
1 m³/s
Set in the form below
You enter
Flow rate (m³/s)
You get
Flow rate (L/s), Flow rate (m³/h), Flow rate (L/min)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a flow rate in cubic meters per second (m³/s) to litres per second (L/s): enter the value in m³/s and it returns the equivalent L/s. The conversion is exact: 1 m³/s equals 1,000 L/s.

Formula

Litres per second equal cubic meters per second multiplied by 1,000:

QL/s = Qm³/s × 1,000

  • Qm³/s is the volume flow rate in cubic meters per second (m³/s).
  • QL/s is the same flow rate in litres per second (L/s).

The factor follows from the volume relationship 1 m³ = 1,000 L. The calculator also shows equivalent rates in cubic meters per hour and litres per minute. It uses 3 decimal places for display; trailing zeros may be omitted by a calculator’s display, but they do not change the value.

Worked Example

Using the default input, Qm³/s = 1 m³/s:

  • Litres per second: 1 × 1,000 = 1,000 L/s.
  • Cubic meters per hour: 1 × 3,600 = 3,600 m³/h.
  • Litres per minute: 1 × 60,000 = 60,000 L/min.

These are three ways of expressing the same flow, not three different flows.

Assumptions

  • The entered number is a volume flow rate in m³/s, not a volume or a speed.
  • The conversion uses the exact metric relationship 1 m³ = 1,000 L and does not depend on the fluid or its temperature.
  • The input is nonnegative; reverse flow, if relevant, must be represented separately with a direction convention.

Why the Conversion Factor Is 1,000

A cubic meter is a cube one meter along each edge. Because one meter is 10 decimeters, the cube contains 10 × 10 × 10 = 1,000 cubic decimeters. A litre is exactly one cubic decimeter, so one cubic meter contains exactly 1,000 litres.

The time unit stays the same when converting m³/s to L/s. Only the volume unit changes, which is why you multiply by 1,000 rather than by 60 or 3,600. Those other factors apply when changing seconds to minutes or hours:

  • 1 m³/s = 1,000 L/s.
  • 1 m³/s = 3,600 m³/h, because an hour has 3,600 seconds.
  • 1 m³/s = 60,000 L/min, combining 1,000 L per cubic meter with 60 seconds per minute.

How to Convert a Flow Rate

Keep the conversion tied to both parts of the unit: volume and time. For a rate already given in cubic meters per second, multiply by 1,000 to get litres per second. To convert the other way, divide by 1,000.

  1. Check that the given value is in m³/s. If it is m³/h, convert the time unit too.
  2. Multiply the numerical value in m³/s by 1,000.
  3. Write the result with units of L/s and retain enough precision for the task.

For example, 0.025 m³/s × 1,000 = 25 L/s. Conversely, 8 L/s ÷ 1,000 = 0.008 m³/s. The numbers change by a factor of 1,000, while the physical flow represented remains the same.

Examples and Practical Context

Flow-rate units appear in water systems, drainage, process engineering, ventilation calculations and scientific measurements. A cubic meter per second is a large rate for many small pipes, so litres per second can be easier to read. In contrast, large rivers or major channels may be reported in m³/s because the larger unit keeps the numerical value manageable.

  • 0.003 m³/s is 3 L/s.
  • 0.4 m³/s is 400 L/s.
  • 2.75 m³/s is 2,750 L/s.

To put a steady rate into perspective, multiply flow by elapsed time to obtain volume. At 3 L/s for 10 seconds, the volume is 30 L. This assumes the rate remains constant for the full interval. If the flow varies, the total volume depends on the changing rate over time; multiplying one instantaneous reading by the duration may not give the actual total.

Common Unit Mistakes and Limits

The most common error is changing the volume unit but overlooking the time unit. For m³/s to L/s, multiply by 1,000. For m³/h to L/s, first account for the 3,600 seconds in an hour: multiply the m³/h value by 1,000 and divide by 3,600. For instance, 36 m³/h = 10 L/s, not 36,000 L/s.

  • Flow rate versus volume: L/s is a rate; L is a volume. A duration is needed to calculate total volume from a steady rate.
  • Flow rate versus velocity: m³/s measures volume passing per unit time; m/s measures distance per unit time. They cannot be converted directly without additional information, such as a cross-sectional area.
  • Rounding: keep useful digits through intermediate calculations, then round the final result to suit the measurement precision. A unit conversion does not create extra measurement accuracy.
  • Direction: a positive rate usually describes magnitude. Systems that distinguish forward from reverse flow need a stated sign or direction convention.

This conversion changes units only. It does not determine whether a pipe, channel or pump can deliver the stated rate, nor does it account for pressure, fluid properties, leakage or changing operating conditions.

Frequently Asked Questions

How many litres per second are in 1 cubic meter per second?
There are exactly 1,000 L/s in 1 m³/s.

How do I convert m³/s to L/s?
Multiply the value in m³/s by 1,000. For example, 0.12 m³/s is 120 L/s.

How do I convert litres per second back to cubic meters per second?
Divide the L/s value by 1,000. For example, 450 L/s is 0.45 m³/s.

Is m³/s the same as m/s?
No. m³/s is volumetric flow rate; m/s is speed. Converting between them requires a relevant cross-sectional area and suitable flow assumptions.

How many litres per second is 1 m³ per hour?
One cubic meter per hour is 1,000 ÷ 3,600 ≈ 0.2778 L/s.

Related

Formula used
in q | Flow rate | m³/s | 1 | 0
out lps | Flow rate | L/s | q * 1000 | 3
out m3h | Flow rate | m³/h | q * 3600 | 3
out lpm | Flow rate | L/min | q * 60000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →