The gas valve flow coefficient, Cv, is a measure of how much gas can pass through a control valve under specified conditions. This calculator estimates Cv from gas flow, upstream pressure, temperature, specific gravity, and pressure drop; its result is a screening estimate, not a substitute for a valve manufacturer’s sizing method.
Formula
This calculator uses a simplified, subcritical gas-flow relationship:
Cv = Q × √[Gg × T / (ΔP × (P1 + ΔP))]
- Cv is the estimated valve flow coefficient, a dimensionless valve-capacity rating.
- Q is gas flow in standard cubic feet per hour (SCFH).
- Gg is gas specific gravity relative to air, which is assigned a value of 1.
- T is absolute gas temperature in degrees Rankine (°R). Convert Fahrenheit using T = °F + 459.67.
- ΔP is pressure drop across the valve in psi.
- P1 is upstream pressure in psia, an absolute pressure.
In this equation, P1 + ΔP represents the downstream absolute pressure because ΔP is defined as upstream minus downstream pressure. The equation is an approximate, non-choked-flow form and omits factors used in formal sizing standards, including gas expansion and valve pressure-recovery factors. Its units and standard-flow convention must match the equation’s assumptions.
Worked Example
Using the calculator defaults—Q = 100 SCFH, P1 = 30 psia, ΔP = 5 psi, temperature = 60 °F, and Gg = 0.6—first convert temperature:
T = 60 + 459.67 = 519.67 °R
Then substitute into the equation:
Cv = 100 × √[(0.6 × 519.67) / (5 × (30 + 5))]
Cv = 100 × √[311.802 / 175] ≈ 100 × 1.3346 = 133.46
Rounded to two decimal places, the calculator result is Cv = 133.46. This is an approximate coefficient for the stated conditions, not a final valve selection.
Assumptions
- The gas behaves approximately as an ideal gas, and the specified specific gravity adequately represents its molecular-weight relationship to air.
- Flow is subcritical and the simplified equation’s pressure and standard-flow conventions apply.
- Pressures are entered in psi, with upstream pressure absolute; temperature is converted from °F to °R.
- The calculation does not include valve geometry, piping effects, compressibility corrections, or manufacturer-specific sizing factors.
What Cv Means for Gas
Cv originated as a practical capacity rating for valves. In its conventional liquid definition, Cv is the water flow in US gallons per minute that produces a pressure drop of 1 psi across a valve under specified reference conditions. Gas flow is compressible, so a liquid Cv definition cannot be applied to gas by simply treating gas like water. Instead, gas-sizing equations use Cv together with pressure, temperature, gas properties, and correction factors.
A larger Cv generally indicates greater flow capacity for a given valve style and conditions. It does not mean that the valve will always deliver a particular flow: actual flow also depends on the pressure ratio, gas composition, temperature, valve opening, and whether flow becomes choked. Cv is a capacity parameter, not a direct measurement of a valve’s position or a universal flow rate.
How to Use and Interpret the Estimate
Enter flow in SCFH, pressure in psi, temperature in °F, and specific gravity relative to air. Use upstream absolute pressure, not gauge pressure. If you have gauge pressure, add local atmospheric pressure to convert it to absolute pressure; near sea level, atmospheric pressure is approximately 14.7 psi, though actual pressure varies with elevation and weather. Use the pressure drop across the valve itself, not the total pressure loss of an entire system unless that is what the calculation is intended to represent.
Specific gravity is the gas density divided by air density at the same reference conditions; equivalently, for ideal gases, it is approximately the gas molecular weight divided by the molecular weight of air. For a gas mixture, use a value appropriate to the actual mixture. Do not assume 0.6 for every fuel gas or process gas.
- For a proposed valve, compare the required Cv with the valve’s published capacity at the intended opening and operating conditions.
- For an existing valve, a calculated Cv can help frame a capacity check, but measured flow and pressure conditions are needed to diagnose performance.
- Check that the flow value uses the same standard temperature and pressure convention as the source data. SCFH conventions are not universal.
Limits, Choked Flow, and Common Errors
The main limitation is that the displayed equation is a simplified estimate. Gas-flow standards and manufacturer methods use additional parameters, commonly including a gas expansion factor, a valve pressure-drop ratio factor, and a critical pressure ratio. These account for real valve behavior and the reduction in gas density as pressure falls. When the downstream-to-upstream pressure ratio is sufficiently low, gas flow can become choked: lowering downstream pressure further no longer increases flow in the way a simple subcritical equation predicts. Do not use this calculator to establish a safety-critical capacity, relief-device size, or final control-valve selection.
Several input mistakes can produce a plausible-looking but misleading result:
- Gauge instead of absolute pressure: using psig as psia understates upstream absolute pressure and distorts the estimate.
- Wrong temperature scale: gas equations require absolute temperature. Fahrenheit must be converted to Rankine; Celsius must first be converted to Kelvin for equations written in SI units.
- Mixed flow units: entering actual cubic feet per hour where the equation expects standard cubic feet per hour changes the meaning of the result.
- Ignoring pressure ratio: a large pressure drop can make choked-flow and expansion corrections essential.
- Overinterpreting precision: two decimal places are a display choice, not evidence that the estimate is accurate to that precision.
For engineering selection, use an applicable recognized gas-valve sizing standard or the valve manufacturer’s documented calculation method, with the actual gas composition and operating envelope. A qualified engineer should review designs where loss of containment, unstable control, or inadequate capacity could create a hazard. Follow your lab method, the safety data sheet (SDS) and your supervisor where bench work is involved.
Frequently Asked Questions
What is the Cv equation for gas?
The simplified subcritical estimate shown here is Cv = Q × √[Gg × T / (ΔP × (P1 + ΔP))], using SCFH, psi, Rankine, and specific gravity relative to air. Formal sizing equations include additional correction factors.
Is gas Cv the same as liquid Cv?
Cv is the same kind of valve-capacity rating, but gas flow is compressible. Gas calculations must account for pressure ratio, temperature, gas properties, and potentially choking; a liquid-flow equation alone is not adequate.
Should I use psig or psia in a gas Cv calculation?
Use the absolute pressure required by the equation. Convert gauge pressure to absolute pressure by adding local atmospheric pressure. Pressure drop remains a difference, so it can be expressed in psi.
What does a higher Cv mean?
It generally means the valve can pass more flow at a given pressure drop under comparable conditions. It does not specify actual flow without the operating pressures, temperature, gas properties, and valve state.
Can this estimate size a gas valve?
It can provide an initial screening value, but not a final selection. Use the applicable sizing standard or manufacturer method, especially when pressure ratios may cause choked flow or when the application is safety-critical.
Related
Formula used
in q | Gas flow | SCFH | 100 | 0 in p1 | Upstream absolute pressure | psia | 30 | 0 in dp | Pressure drop | psi | 5 | 0 in t | Gas temperature | °F | 60 | -459.67 in sg | Gas specific gravity (air=1) | - | 0.6 | 0 out cv | Estimated gas valve coefficient Cv | - | q * sqrt(sg * (t + 459.67) / (dp * (p1 + dp))) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol