Acetone’s density is about 784 kg/m³ at 20 °C (equivalent to 0.784 kg/L or 0.784 g/cm³). This calculator converts a measured acetone mass and volume into density; enter both values and it returns density in kg/m³, with the converted mass and volume shown as supporting results.
Formula
Density is mass divided by volume:
ρ = m / V
- ρ is density in kilograms per cubic metre (kg/m³).
- m is mass in kilograms (kg). This calculator accepts grams and converts them to kilograms by dividing by 1,000.
- V is volume in cubic metres (m³). This calculator accepts millilitres and converts them to cubic metres by dividing by 1,000,000.
Therefore, with the calculator’s inputs, ρ = (m in g / 1,000) / (V in mL / 1,000,000). The first output is density, as requested. The other outputs display the converted mass and volume used in the calculation. Density is a ratio of mass to volume; it is not the same as mass, nor does it specify how much acetone is in a container unless the volume is also known.
Worked Example
Using the default inputs, the mass is 196 g and the volume is 250 mL.
- Convert mass: 196 g / 1,000 = 0.196 kg.
- Convert volume: 250 mL / 1,000,000 = 0.000250 m³.
- Divide mass by volume: 0.196 kg / 0.000250 m³ = 784 kg/m³.
The calculator displays 784 kg/m³. This agrees with the approximate reference density of acetone at 20 °C. A measured sample may differ slightly because of temperature, purity, measurement uncertainty, or contamination.
Assumptions
- The inputs describe the mass and volume of the same sample.
- Mass is entered in grams and volume in millilitres; the formula converts both to SI units.
- The result is the sample’s measured density. The calculator does not assume a reference temperature or correct for temperature.
- The reference value of about 784 kg/m³ applies to acetone near 20 °C and is not a universal value at every temperature or purity.
Why Acetone’s Density Depends on Temperature
Density changes when a liquid expands or contracts. For most liquids, warming increases volume while mass stays the same, so density decreases. Cooling generally has the opposite effect. Thus, a density quoted without a temperature is incomplete for precise work. The commonly cited value near 784 kg/m³ is a useful room-temperature reference, not a promise that every acetone sample will measure exactly that number.
Purity also matters. Acetone mixed with water or another solvent does not necessarily have the density of pure acetone; the mixture’s density depends on its composition and temperature. A reference table for pure acetone should not be used to identify or quantify an unknown mixture by density alone. Other liquids can have similar densities, and measurement errors can mask small differences.
Putting the Value in Context
A cubic metre of acetone at the reference condition would have a mass of about 784 kg. A litre would have a mass of about 0.784 kg, or 784 g. Conversely, one kilogram of acetone occupies approximately 1.28 L near 20 °C, since 1 kg / 0.784 kg/L ≈ 1.28 L. These are conversions from the same approximate density, not separate fixed properties.
Acetone is less dense than water near room temperature: water is close to 1,000 kg/m³ at ordinary laboratory temperatures. That difference helps explain why a separate layer of pure acetone tends to sit above water. However, acetone and water are miscible, meaning they mix rather than remaining as stable, separate layers. The comparison should not be taken to mean acetone floats as a persistent layer after mixing.
Measurement and Common Errors
To calculate a sample’s density, measure the mass and the volume of that same sample, then use consistent units or convert them correctly. For a bench measurement, use a suitable method and equipment for the sample and volume. Follow your lab method, the safety data sheet (SDS) and your supervisor.
- Mixing units: Dividing grams by millilitres gives g/mL, not kg/m³. The numerical values happen to match—1 g/mL equals 1,000 kg/m³, not 1 kg/m³. For example, 0.784 g/mL equals 784 kg/m³.
- Using container volume as sample volume: A container’s stated capacity does not guarantee it holds that exact volume. Use the actual volume of the measured sample.
- Ignoring temperature: Record the temperature when comparing results to a reference value, especially when precision matters.
- Rounding too early: Keep unrounded measurements through the calculation and round the final result to a precision justified by the instruments and method.
- Assuming an unknown liquid is acetone: Density alone is not a reliable identification test. Never infer identity or purity from one approximate density measurement.
Safety and Scope
Acetone is a highly flammable, volatile solvent. Its vapour can ignite, so keep it away from flames, sparks, hot surfaces, and other ignition sources. Avoid breathing vapour and avoid skin and eye contact; consult the current SDS for suitable handling, protective equipment, storage, spill response, and disposal guidance. Use appropriate ventilation and follow local rules. The density calculation itself does not determine whether a sample is safe to handle.
This calculator is for general measurement and study. It does not account for evaporation during handling, dissolved substances, temperature correction, or instrument calibration. If the result must meet a formal specification, use the applicable validated method and reference conditions rather than relying on a rounded general value.
Frequently Asked Questions
What is the density of acetone in kg/m³?
About 784 kg/m³ at 20 °C. The value varies with temperature and sample composition.
What is acetone’s density in g/mL?
Approximately 0.784 g/mL near 20 °C. Multiply g/mL by 1,000 to convert to kg/m³.
Is acetone denser than water?
No. Near room temperature, acetone is less dense than water. Acetone and water nevertheless mix readily, so they do not remain as separate layers.
Does acetone density change with temperature?
Yes. Like most liquids, acetone expands as it warms, so its density generally falls; cooling generally increases it.
How much does one litre of acetone weigh?
At the approximate density of 0.784 kg/L, one litre has a mass of about 0.784 kg, or 784 g. The actual mass depends on temperature and purity.
Can density identify pure acetone?
Not by itself. Measurement conditions and mixtures affect density, and different substances can have similar values. Use an appropriate validated identification or purity method.
Related
Formula used
in m | Acetone mass | g | 196 | 0 in v | Acetone volume | mL | 250 | 0 out d | Density | kg/m³ | (m / 1000) / (v / 1000000) | 0 out ml | Mass | kg | m / 1000 | 3 out vl | Volume | m³ | v / 1000000 | 6
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol