molecalculator

Moles & Molar Mass

Density of Air at 293 K: Value and Calculation

Calculator No. 01-1707 · Updated · Formula and assumptions shown below

Air density 1.2047 kg/m^3
Air density
1.2047 g/L
= Air density
Air density
0.07521 lb/ft^3
= Air density × 0.06242796
Air temperature
293 K
Set in the form below
You enter
Air temperature (K), Absolute pressure (kPa), Relative humidity (%)
You get
Air density (kg/m^3), Air density (g/L), Air density (lb/ft^3)
Rounding
4 dp · 5 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

At 293 K (19.85 °C), dry air at standard atmospheric pressure of 101.325 kPa has a density of about 1.204 kg/m³. The exact value depends on pressure, humidity, and the composition of the air, so this calculator estimates density from temperature, pressure, and relative humidity using the ideal-gas model.

Formula

For moist air, the calculator treats dry air and water vapor as separate ideal gases occupying the same volume. It calculates their partial pressures, then adds their mass densities:

ρ = (p − e)/(RdT) + e/(RvT)

  • ρ is air density in kg/m³.
  • p is absolute total pressure in pascals. The calculator converts the input from kPa using 1 kPa = 1,000 Pa.
  • e is water-vapor partial pressure in pascals.
  • T is absolute temperature in kelvins.
  • Rd is the specific gas constant for dry air, 287.05 J/(kg·K).
  • Rv is the specific gas constant for water vapor, 461.495 J/(kg·K).

The vapor pressure is estimated as e = (RH/100) × es, where RH is relative humidity in percent and es = 610.94 × exp[17.625 × tC/(tC + 243.04)] Pa. Here, tC = T − 273.15 is temperature in °C. This saturation-vapor-pressure approximation is intended for ordinary near-surface temperatures, not extreme conditions.

Worked Example

Use the defaults: T = 293 K, p = 101.325 kPa, and RH = 0%. At zero humidity, e = 0, so the density reduces to the dry-air expression.

First, convert pressure: 101.325 × 1,000 = 101,325 Pa. Then:

ρ = 101,325 / (287.05 × 293) = 101,325 / 84,104.65 ≈ 1.20404 kg/m³.

Rounded to the calculator’s four decimal places, the result is 1.2040 kg/m³. Since 1 kg/m³ equals 1 g/L, the second output is 1.2040 g/L. For pounds per cubic foot, 1.20404 × 0.06242796 ≈ 0.07515 lb/ft³.

Assumptions

  • Air and water vapor behave as ideal gases.
  • The dry-air and water-vapor gas constants are treated as fixed.
  • Relative humidity is between 0% and 100%, and the vapor-pressure approximation is used at ordinary temperatures.
  • Pressure is absolute pressure, not gauge pressure.
  • Air composition is represented by the conventional dry-air gas constant; unusual gas mixtures are not covered.

What 293 K Means

Kelvin is an absolute temperature scale: 0 K is absolute zero, and a change of 1 K is the same size as a change of 1 °C. To convert kelvins to Celsius, subtract 273.15. Thus 293 K is 19.85 °C, commonly rounded to 20 °C in everyday descriptions.

Temperature alone does not fix air density. At a fixed pressure, warming air makes it less dense; at a fixed temperature, increasing pressure makes it denser. Humidity also matters because water molecules have a lower molar mass than the average molecules in dry air. Replacing some dry air with water vapor therefore slightly lowers the density at the same temperature and total pressure.

Why the Standard Answer Is About 1.2 kg/m³

The often-quoted value near 1.2 kg/m³ assumes air near room temperature and ordinary sea-level pressure. For dry air at 293 K and 101.325 kPa, the ideal-gas calculation gives about 1.204 kg/m³. It is a useful reference, not a universal constant: weather systems, altitude, indoor heating, and moisture can shift the actual value.

The underlying relation comes from the ideal gas law, PV = nRT. Expressing the amount of gas as mass and using the molar mass of air leads to density being proportional to pressure and inversely proportional to temperature. The calculator’s dry-air constant incorporates the average composition and molar mass of ordinary dry air.

How to Use the Result

Enter temperature in kelvins, absolute pressure in kPa, and relative humidity as a percentage. For example, enter 50 for 50% humidity, not 0.50. The first result is the estimated density in kg/m³; the next is the numerically equivalent value in g/L. The final output converts the result to lb/ft³.

  • Use local station pressure or another absolute pressure measurement. A weather report corrected to sea level may not equal the pressure at your location.
  • If you only need a rough room-temperature estimate, 1.2 kg/m³ is often adequate.
  • For a more exact engineering or scientific calculation, use a moist-air standard or equation of state suited to the relevant temperature and pressure range.

Common Mistakes and Limits

A frequent mistake is treating 293 K as 293 °C. It is approximately 20 °C; using the wrong temperature scale produces a seriously incorrect result. Another is entering gauge pressure as if it were absolute pressure. Gauge pressure is measured relative to ambient pressure, whereas the gas law requires pressure relative to a vacuum. Near sea level, a gauge reading of zero corresponds to roughly 101.3 kPa absolute, not zero.

The calculator uses an ideal-gas approximation and a simple saturation-vapor-pressure equation. It is suitable for ordinary atmospheric calculations, but it does not account for detailed changes in air composition, strong non-ideal behavior, or special high-accuracy meteorological conventions. Near saturation, humidity measurements and temperature uncertainty can also affect the estimate. Do not interpret the displayed digits as a guarantee of measurement precision.

Frequently Asked Questions

What is the density of dry air at 293 K?
At 101.325 kPa, the ideal-gas estimate is about 1.204 kg/m³, or 1.204 g/L.

Is 293 K the same as 20 °C?
Not exactly: 293 K equals 19.85 °C. It is commonly rounded to 20 °C.

Does humidity make air heavier?
At the same temperature and total pressure, higher humidity usually makes air less dense. Water vapor has a lower molar mass than the average dry-air mixture.

Does air density change with altitude?
Yes. Atmospheric pressure generally decreases with altitude, so air density usually decreases as well, though temperature and weather also influence it.

What pressure should I use?
Use absolute local pressure in kPa. Do not use a gauge-pressure value without adding the surrounding atmospheric pressure.

Related

Formula used
in t | Air temperature | K | 293 | 0
in p | Absolute pressure | kPa | 101.325 | 0
in rh | Relative humidity | % | 0 | 0 | 100
out rho | Air density | kg/m^3 | (p * 1000 - (rh / 100) * 610.94 * exp(17.625 * (t - 273.15) / ((t - 273.15) + 243.04))) / (287.05 * t) + ((rh / 100) * 610.94 * exp(17.625 * (t - 273.15) / ((t - 273.15) + 243.04))) / (461.495 * t) | 4
out rho_g | Air density | g/L | rho | 4
out rho_lb | Air density | lb/ft^3 | rho * 0.06242796 | 5

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →