molecalculator

Moles & Molar Mass

Density of Ethanol in mL: g/mL Values & How to Measure

Calculator No. 01-8944 · Updated · Formula and assumptions shown below

Density 0.7893 g/mL
Specific gravity (water = 1)
0.7907
= Density ÷ 0.9982
Mass of ethanol
100 g
Set in the form below
Volume of ethanol
126.7 mL
Set in the form below
You enter
Mass of ethanol (g), Volume of ethanol (mL)
You get
Density (g/mL), Specific gravity (water = 1)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The density of ethanol is 0.789 g/mL at 20 °C (68 °F). This means 1 milliliter of pure (absolute) ethanol weighs 0.789 grams. The value changes slightly with temperature, so you will often see it listed as 0.789 g/mL at 20 °C or 0.785 g/mL at 25 °C.

Formula

Density (ρ) is mass divided by volume:

ρ = m / V

  • ρ = density in grams per milliliter (g/mL)
  • m = mass in grams (g)
  • V = volume in milliliters (mL)

For ethanol, the standard reference value is 0.789 g/mL at 20 °C. This is the density of absolute (100%) ethanol. If you have a water-ethanol mixture, the density is different and depends on the alcohol percentage.

Worked Example

Using the default values from the calculator above: you have 100 g of ethanol and a volume of 126.7 mL.

Step 1: Write the formula.

ρ = m / V

Step 2: Plug in the numbers.

ρ = 100 g / 126.7 mL

Step 3: Divide.

ρ = 0.7893 g/mL

The calculator rounds to 4 decimal places, giving 0.7893 g/mL. This matches the accepted density of ethanol at 20 °C.

Assumptions

  • Pure (absolute) ethanol, not a mixture with water or other solvents.
  • Temperature is 20 °C (standard room temperature).
  • Pressure is 1 atm (density of liquids is nearly independent of pressure).
  • The ethanol contains no dissolved solids or additives.

Why Density Changes with Temperature

Like most liquids, ethanol expands when heated and contracts when cooled. As temperature rises, the same mass occupies more volume, so density decreases. The change is about 0.0008 g/mL per °C near room temperature. For example:

  • At 15 °C: density ≈ 0.794 g/mL
  • At 20 °C: density ≈ 0.789 g/mL
  • At 25 °C: density ≈ 0.785 g/mL
  • At 30 °C: density ≈ 0.781 g/mL

This is why laboratory measurements always report the temperature. If you need high accuracy, you must control or measure the temperature.

How to Measure Density of Ethanol

There are three common methods to measure the density of ethanol in a lab or at home:

  1. Hydrometer: A glass float that sinks to a level determined by the liquid density. Read the scale at the liquid surface. For ethanol, use an alcoholometer (a type of hydrometer calibrated for ethanol-water mixtures).
  2. Pycnometer: A precisely calibrated glass bottle. Weigh the empty bottle, fill with ethanol, weigh again, and divide the mass difference by the known volume.
  3. Electronic density meter: Uses the oscillation frequency of a U-shaped tube. It gives the most precise readings and automatically corrects for temperature.

For a quick estimate, you can also weigh a known volume with a graduated cylinder and an analytical balance.

Ethanol Density vs. Water Density

Water has a density of 0.9982 g/mL at 20 °C, which is higher than ethanol’s 0.789 g/mL. This difference is why:

  • Ethanol floats on water (if carefully layered).
  • Adding ethanol to water reduces the overall density of the mixture.
  • Alcohol-water mixtures have a lower density than pure water, which is how alcoholometers work.

The specific gravity of ethanol is 0.789 / 0.9982 = 0.7905 at 20 °C (relative to water at the same temperature). Specific gravity is unitless.

Common Mistakes and Misconceptions

Mistake 1: Using the density of ethanol for a 70% solution. A 70% (v/v) ethanol solution has a density of about 0.868 g/mL, not 0.789. The density of a mixture is not a linear average; it depends on the exact concentration and temperature.

Mistake 2: Confusing mL with cm³. 1 mL = 1 cm³, so the density in g/mL is numerically identical to g/cm³. No conversion is needed.

Mistake 3: Ignoring temperature. If you measure at 25 °C but use the 20 °C value, you’ll get a small error (about 0.5%). For precise work, always note the temperature.

Mistake 4: Assuming density is constant with concentration. Ethanol is hygroscopic and absorbs water from air. Even “absolute” ethanol can contain up to 0.5% water, slightly lowering its density.

Why Density Matters in Practice

Knowing the density of ethanol is essential in several real-world contexts:

  • Preparing solutions: To make a known molarity, you often need to measure volume rather than mass. Density lets you convert between them.
  • Quality control in beverages: The alcohol content of spirits is determined by measuring density before and after distillation.
  • Fuel blending: Ethanol-gasoline blends (like E10) are mixed by volume, but the energy content is often expressed per mass. Density helps convert.
  • Chemical synthesis: When a procedure says “add 10 g of ethanol,” you can measure 12.7 mL instead if you know the density.

Safety and Handling

Ethanol is flammable and volatile. Keep it away from open flames and sparks. Work in a well-ventilated area. If you spill it, clean up immediately. For laboratory work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

Q: What is the density of ethanol in g/mL at 25 °C?
At 25 °C, the density of pure ethanol is about 0.785 g/mL. The difference from 20 °C is about 0.004 g/mL.

Q: How do I convert ethanol density to specific gravity?
Divide the density of ethanol by the density of water at the same temperature. For 20 °C: 0.789 / 0.9982 = 0.7905.

Q: Is the density of 95% ethanol the same as pure ethanol?
No. 95% (v/v) ethanol has a density of about 0.805 g/mL, because the water content increases density. Always use the density that matches your exact concentration.

Q: Why is ethanol less dense than water?
Ethanol molecules are longer and have a smaller proportion of polar -OH groups per molecule, so they pack less efficiently and have weaker hydrogen bonding per unit volume compared to water.

Q: Can I use a hydrometer to measure ethanol density?
Yes, but use an alcoholometer calibrated for ethanol-water mixtures. A regular hydrometer for general liquids will work only if you calibrate it with known solutions.

Q: What is the density of ethanol vapor?
Ethanol vapor is about 1.59 g/L at 20 °C and 1 atm, which is about 1.5 times denser than air. This is why ethanol vapors can sink and travel along surfaces.

Related

Formula used
in m | Mass of ethanol | g | 100 | 0
in v | Volume of ethanol | mL | 126.7 | 0
out d | Density | g/mL | m / v | 4
out spgr | Specific gravity (water = 1) | - | d / 0.9982 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →