Nitric acid does not have one density: it depends mainly on the acid’s concentration and temperature. For a common concentrated reagent containing about 68% nitric acid by mass at 20 °C, the density is approximately 1.41 g/mL; use the product’s stated concentration and density when precision matters.
Formula
This calculator reports the density supplied for the nitric acid solution: ρ = d. Here, ρ is density in grams per millilitre (g/mL), and d is the reference density in g/mL for the selected solution concentration and temperature. The other inputs identify the solution conditions; they do not independently determine density. Nitric acid density is a measured, condition-dependent property, so a concentration and temperature alone are not enough for an accurate calculation without a reliable density table or measurement.
The supporting volume calculation is V = m / ρ. For the example output, V is the volume in millilitres, m is a chosen solution mass of 100 g, and ρ is density in g/mL. The mass percentage p means grams of pure HNO3 per 100 g of solution. Temperature t is in degrees Celsius. The default density is a conventional approximate value for a roughly 68% by-mass solution near 20 °C, not a universal constant.
Worked Example
Using the defaults—68% nitric acid by mass, 20 °C, and density 1.41 g/mL—the density result is:
ρ = d = 1.41 g/mL.
For a 100 g sample, its approximate volume is:
V = m / ρ = 100 g / (1.41 g/mL) = 70.921… mL ≈ 70.92 mL.
This example shows why density is useful for converting between a solution’s mass and volume. The displayed density has three decimal places, but the source value is approximate; extra digits in the calculated volume do not make the original density more precise.
Assumptions
- The default represents a typical concentrated aqueous nitric acid solution near 68% by mass at about 20 °C; actual grades and measured values can differ.
- The solution is treated as homogeneous, and the density is supplied as an input rather than predicted from concentration.
- The example’s 100 g is total solution mass, not 100 g of pure nitric acid.
Why Nitric Acid Density Varies
Nitric acid, HNO3, is commonly sold as an aqueous solution. Adding dissolved acid changes the mass and volume in a way that is not simply additive, so density changes with composition. Temperature also matters: most liquids expand as they warm, lowering density, although the size of the change depends on the solution.
Concentration is often given as mass percent. A label reading 68% by mass means 68 g of HNO3 in every 100 g of solution; it does not mean 68 g in 100 mL. The remaining mass is principally water, subject to the grade’s specifications. Commercial concentrated nitric acid is often around 68–70% by mass, but grades and specifications vary. A density close to 1.41 g/mL is a useful approximate reference near room temperature, not a substitute for the certificate or technical data for a particular product.
Converting Between Mass and Volume
Density links mass and volume through ρ = m/V. Rearranging gives m = ρV and V = m/ρ. For example, at 1.41 g/mL, 10 mL of solution has an approximate mass of 14.1 g. Conversely, 100 g occupies about 70.9 mL. These conversions apply to the whole solution. To estimate the pure-acid mass in a sample, multiply the solution mass by the mass fraction: 0.68 × 100 g = 68 g HNO3.
Keep units consistent. If density is in g/mL, use mass in grams and volume in millilitres. Since 1 mL = 1 cm3, a density of 1.41 g/mL is also 1.41 g/cm3. It is not 1.41 g/L; converting to g/L gives approximately 1,410 g/L.
Choosing the Right Density Value
For a quick estimate, use a reference value that matches both the concentration and temperature as closely as possible. For calculations tied to a specific reagent, consult the product label, safety data sheet (SDS), certificate of analysis, or a recognized density table. Check whether concentration is stated by mass, volume, or as a molarity; these are not interchangeable without additional information.
- Concentration: distinguish, for example, 68% by mass from 68% by volume.
- Temperature: a tabulated density at 20 °C may not match a warmer or colder sample.
- Product grade: impurities, stabilizers, and permitted specification ranges can produce small differences.
- Precision: use only as many significant figures as the source value supports.
A density measurement can be useful when an exact sample value is required, but it must be made with an appropriate method and suitable equipment. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Common Misunderstandings and Limits
A frequent mistake is treating nitric acid’s density as a fixed constant. The familiar approximate figure of 1.41 g/mL applies to a particular concentrated aqueous range near a stated temperature; dilute nitric acid has a different density. Another mistake is assuming that 1 mL always contains 1 g. That is approximately true for water near ordinary room temperature, not for concentrated nitric acid solution.
This calculator does not infer density from the concentration or temperature fields. That would require a validated density-versus-concentration-and-temperature relationship or an appropriate table. Do not use the default for high-accuracy analytical work, an unknown sample, or a material whose concentration differs materially from the reference. Density also does not by itself establish purity or concentration.
Safety
Nitric acid is corrosive and can cause severe burns and eye damage; concentrated solutions can also release hazardous fumes and act as strong oxidizers. Density arithmetic is not a handling instruction. Consult the current SDS and approved institutional procedures, use the required engineering controls and protective equipment, and do not handle the material outside an appropriately equipped, supervised setting. Never identify an unknown acid by smell or by an improvised test.
Frequently Asked Questions
What is the density of concentrated nitric acid in g/mL?
For a common solution around 68% by mass at approximately 20 °C, it is about 1.41 g/mL. Check the specific product data because concentration and temperature affect the value.
Is nitric acid density always 1.41 g/mL?
No. That is an approximate reference for a concentrated aqueous solution. More dilute solutions, different grades, and different temperatures can have different densities.
How many grams are in 1 mL of nitric acid?
At a density of 1.41 g/mL, 1 mL of that solution has a mass of about 1.41 g. The amount of pure HNO3 in that volume also depends on the solution’s mass concentration.
Is 68% nitric acid the same as 68 g per 100 mL?
Not when the label means 68% by mass. It means 68 g of HNO3 per 100 g of solution. Converting that to a volume basis requires density.
Does temperature change nitric acid density?
Yes. Temperature affects a liquid’s volume and therefore its density. Use a value tabulated or specified at the sample’s temperature when accuracy is important.
Related
Formula used
in p | Nitric acid mass percentage | % | 68 | 0 | 100 in t | Temperature | °C | 20 | -273.15 in d | Density at stated concentration and temperature | g/mL | 1.41 | 0 out rho | Nitric acid solution density | g/mL | d | 3 out ml | Volume of 100 g of solution | mL | 100 / d | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %