molecalculator

Moles & Molar Mass

Density Units in kg: How to Calculate and Convert

Calculator No. 01-1736 · Updated · Formula and assumptions shown below

Density 1,000.000 kg/m³
Density
1.000 g/cm³
= Density ÷ 1000
Mass
1 kg
Set in the form below
Volume
0.001 m³
Set in the form below
You enter
Mass (kg), Volume (m³)
You get
Density (kg/m³), Density (g/cm³)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Density is mass per unit volume, so its SI unit is kilograms per cubic metre (kg/m³), not kilograms (kg) alone. This calculator uses an object’s mass and volume to find its density in kg/m³ and, when useful, converts that value to g/cm³.

Formula

Density equals mass divided by volume:

ρ = m / V

  • ρ (rho) is density, in kilograms per cubic metre (kg/m³).
  • m is mass, in kilograms (kg).
  • V is volume, in cubic metres (m³).

The conversion used for the second result is 1 g/cm³ = 1000 kg/m³, so density in g/cm³ equals density in kg/m³ divided by 1000. The calculator assumes the mass and volume describe the same material or object and that the volume is greater than zero.

Worked Example

Using the calculator’s default values, the mass is 1 kg and the volume is 0.001 m³.

  1. Apply the density formula: ρ = m / V.
  2. Substitute the values: ρ = 1 kg / 0.001 m³.
  3. Calculate: ρ = 1000 kg/m³.
  4. Convert to grams per cubic centimetre: 1000 / 1000 = 1 g/cm³.

The results are 1000 kg/m³ and 1 g/cm³, respectively.

Assumptions

  • Mass and volume refer to the same sample.
  • Volume is the material’s volume, not the volume of empty space around it.
  • The calculator reports an average density; it does not account for changes with temperature, pressure, composition, or location within a nonuniform object.

What Density Units Mean

A kilogram measures mass, while a cubic metre measures volume. Density combines the two as a ratio: how many kilograms of matter are present in each cubic metre. Writing a density simply as “kg” leaves out the volume and therefore does not specify a density.

In the International System of Units (SI), kg/m³ is the standard unit. Other units are common in particular fields and for particular scales:

  • g/cm³ is convenient for solids and liquids. Water near ordinary room temperature has a density close to 1 g/cm³, or about 1000 kg/m³.
  • g/mL is often used for liquids. Since 1 mL equals 1 cm³, 1 g/mL equals 1 g/cm³.
  • kg/L is another practical liquid unit. Numerically, 1 kg/L equals 1 g/cm³ and 1000 kg/m³.
  • g/L is common for dilute mixtures. For example, 1 g/L equals 1 kg/m³.

These equivalent units describe the same physical property. The number changes when the unit changes, so always include the unit with a reported value.

How to Convert Density to kg/m³

Convert the mass and volume units into kilograms and cubic metres before dividing, or apply the appropriate density conversion factor. Useful equalities include:

  • 1 g/cm³ = 1000 kg/m³
  • 1 g/mL = 1000 kg/m³
  • 1 kg/L = 1000 kg/m³
  • 1 g/L = 1 kg/m³

For example, a liquid with density 0.8 g/mL has density 800 kg/m³: multiply 0.8 by 1000. In the other direction, divide kg/m³ by 1000 to get g/cm³. A frequent mistake is multiplying when converting from kg/m³ to g/cm³; because a cubic centimetre is much smaller than a cubic metre, the numerical value in g/cm³ is smaller.

Using Mass and Volume Correctly

Choose measurements that match the sample. Mass can be measured on a balance, while volume may be determined from dimensions, displacement, or a suitable volume measurement. The method depends on whether the sample is a regular solid, an irregular object, a liquid, or a porous material. When calculating from dimensions, make sure all lengths are converted to metres before finding volume in m³.

For a rectangular block, volume is length × width × height. If its sides are 0.10 m, 0.05 m, and 0.02 m, its volume is 0.0001 m³. If its mass is 0.25 kg, its average density is 0.25 / 0.0001 = 2500 kg/m³. Small errors in a dimension can noticeably affect the result because volume depends on multiple measurements.

For an irregular object that does not dissolve or absorb the liquid used for measurement, volume can be found from the rise in liquid level. Subtract the initial reading from the final reading, then convert the resulting volume to m³ if using this calculator. Avoid including a container’s mass in the object’s mass; if needed, subtract the empty container’s mass first.

Why Density Values Vary

Density is not always a fixed number for a named substance. Temperature changes can cause expansion or contraction, changing volume and therefore density. Pressure has a larger effect on gases than on most liquids and solids. Mixtures and porous materials can also have different densities depending on their composition and on whether the measured volume includes pores or gaps.

Distinguish bulk density from the density of the material itself. Bulk density includes the spaces between particles in a packed powder or granular sample, while a particle’s material density does not. Similarly, an object with cavities may have a lower average density based on its external dimensions than the density of the solid material making up its walls.

Frequently Asked Questions

Is kg a unit of density?
No. A kilogram is a unit of mass. Density needs both mass and volume, such as kg/m³ or g/cm³.

What is the SI unit of density?
The SI unit is kilogram per cubic metre, written kg/m³.

How many kg/m³ are in 1 g/cm³?
There are 1000 kg/m³ in 1 g/cm³. Multiply a value in g/cm³ by 1000 to convert it to kg/m³.

Is g/mL the same as g/cm³?
Yes. One millilitre is exactly one cubic centimetre, so the units are equivalent.

How do I calculate density if I know mass and volume?
Divide the mass by the volume, using compatible units. For a result in kg/m³, enter mass in kg and volume in m³.

Does water always have a density of 1000 kg/m³?
No. That is a useful approximation, not an exact value under all conditions. Water density varies with temperature and pressure.

Related

Formula used
in m | Mass | kg | 1 | 0
in v | Volume | m³ | 0.001 | 0
out d | Density | kg/m³ | m / v | 3
out dg | Density | g/cm³ | d / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →