molecalculator

Moles & Molar Mass

Dilution Calculator by Percentage: Mix Solutions

Calculator No. 01-6036 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A dilution calculator by percentage tells you how much stock solution and diluent to combine to reach a target concentration. Enter the stock percentage, desired percentage, and final volume; the calculator returns the stock volume and the amount of diluent, assuming both percentages use the same concentration basis.

Formula

The standard dilution equation is C1V1 = C2V2. Solving for the stock volume gives V1 = C2V2 / C1. In the calculator, stock concentration is s (%), target concentration is t (%), and desired final solution volume is v (mL). The output a is stock volume (mL); diluent d is final volume minus stock volume (mL).

Because the percentage units cancel, the percentages can be entered as ordinary numbers such as 10 and 2, rather than 0.10 and 0.02. Their concentration bases must match: for example, percent by volume must be diluted to a target also expressed by volume. The formula assumes the final volume is the stated volume; it does not assume that adding the two measured volumes always produces an exact final volume.

Worked Example

Using the calculator defaults: s = 10%, t = 2%, and v = 100 mL.

  1. Stock volume: a = (v × t) / s = (100 mL × 2) / 10 = 20.00 mL.
  2. Diluent volume: d = v − a = 100 mL − 20.00 mL = 80.00 mL.

So, for a 100 mL final solution at 2% from a 10% stock, the calculation calls for 20.00 mL of stock and enough diluent to bring the mixture to a final volume of 100 mL.

Assumptions

  • Stock and target percentages describe the same kind of concentration and use compatible units.
  • The stock is uniform, and dilution does not cause a chemical reaction or loss of the solute.
  • “Final volume” means the volume of the completed solution, not the volume of diluent alone.
  • The arithmetic treats volumes as additive when it reports diluent as final volume minus stock volume. For precise preparation, bring the mixture to the specified final volume using the applicable method.

What Percentage Dilution Means

A percentage describes a proportion, but the meaning depends on the convention used. Common forms include percent by volume (mL per 100 mL of solution), percent by mass (g per 100 g of solution), and mass per volume (often g per 100 mL). These are not interchangeable. A label or protocol should specify the basis, and the stock and target values must use the same basis for this simple dilution equation to apply directly.

For instance, a 10% v/v solution and a 2% v/v target can be related with the calculator. A 10% w/w stock and a 2% w/v target cannot be treated as equivalent merely because both use the number 10 or 2; density and unit conversions may be needed. If a product label gives a concentration in different units, convert it to a compatible basis before calculating.

How to Use the Calculator

  • Read the stock concentration and identify its percentage basis.
  • Choose a target concentration on that same basis. The target cannot exceed the stock concentration for an ordinary dilution.
  • Enter the desired final volume, not just the amount of diluent you plan to add.
  • Use the stock-volume result to measure the stock, then add diluent until the mixture reaches the intended final volume when accurate final-volume preparation matters.

The calculator rejects a target greater than the stock concentration because the required stock volume would exceed the final volume; dilution cannot make a solution more concentrated. A target of zero gives zero stock by the equation, while a zero stock concentration cannot produce a nonzero target and is not a valid divisor.

Reading the Result and Avoiding Errors

The first result is the calculated amount of stock. The second is the arithmetic difference between the target final volume and that stock amount. Do not mistake the diluent result for a direction to combine two volumes and assume their sum is exact. When volumes change on mixing, or when a specified concentration and final volume must be accurate, use the stock amount and bring the solution to the final volume rather than adding a premeasured full amount of diluent.

  • Mixing percentage bases: Confirm whether each percentage is w/w, v/v, or w/v.
  • Entering a fraction instead of a percent: Enter 2 for 2%, not 0.02, because the calculator expects percentage points.
  • Using the wrong volume: The input is final solution volume. If you need 100 mL final, do not enter 100 mL as the diluent amount.
  • Rounding too early: Keep extra digits during intermediate calculations and round measured amounts to a precision your equipment and method can support.
  • Trying to concentrate by dilution: If the target exceeds the stock, choose a more concentrated stock or use a separate concentration method.

Limits and Practical Context

The equation conserves the amount of solute during dilution: the amount present in the measured stock portion equals the amount in the final solution. It does not determine whether a particular substance is soluble, stable, compatible with the diluent, or safe to handle. It also does not account for evaporation, reaction, adsorption, temperature effects, or density changes. Those may matter for a real preparation and must be addressed by the relevant method.

For a stock reported in molarity, mass concentration, or another non-percentage unit, use a dilution calculation with compatible concentration units rather than relabeling the value as a percentage. If converting between mass-based and volume-based concentrations, the substance’s density may be required. Bench work should follow the applicable lab method, safety data sheet (SDS), and supervisor’s instructions.

Frequently Asked Questions

How do I calculate a dilution percentage?
Use C1V1 = C2V2. Rearrange to V1 = C2V2 / C1, with stock and target concentrations expressed on the same basis.

How much 10% stock makes 100 mL of 2% solution?
The calculation gives 20 mL of 10% stock. Add diluent to make a final volume of 100 mL; the simple volume difference is 80 mL.

Do I add the calculated diluent to the stock?
The calculator’s diluent value is a volume difference. For a precise final volume, add less than that amount initially if appropriate, mix, then bring the solution to the specified final volume using the relevant method.

Can I dilute a 2% solution to 10%?
No. Dilution lowers concentration. A target above the stock concentration requires a stronger starting stock or a different concentration process.

Can I use this for percent by weight and percent by volume?
Only when the stock and target use the same percentage basis. Converting between w/w, v/v, and w/v can require density or other information not included in this calculator.

Related

Formula used
in s | Stock concentration | % | 10 | 0 | 100
in t | Target concentration | % | 2 | 0 | 100
in v | Final solution volume | mL | 100 | 0 |
out a | Stock solution to use | mL | v * t / s | 2
out d | Diluent to add | mL | v - a | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →